Finally got my rear bar on.... had to DIY - PICS!!!

Have some questions about how to achive better handling and stopping power using different springs, upgrading to coilovers, questions on swaybars, bushings, different rotors, pads, ect... Having any steering problems or questions about steering racks, tie rods, tie rod ends, ect... ask these questions here.
Post Reply
User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Finally got my rear bar on.... had to DIY - PICS!!!

Post by CA180 » Fri Aug 25, 2006 7:52 pm

Well, i got the rear bar strut tabs in from chrysler... but everything didnt go as planned.

The 2004 r/t rear bar and struts have the holes lined up for a vertical endlink. The tabs are built for a horizontal endlink... so i had to make my own endlinks that would finally join the two up. So heres what i did!

I built my own Heim Joint sway bar endlinks... alot easier than i would have thought. I'll post the pics i took later when i figure out how in the crap you use photobucket...

the endlinks basically consisted of: two really long bolts, four of the stock endlink bushings, two heim joints, and some various nuts, bolts, and washers.

Turned out pretty sweet if you ask me... like i said, i load up some pics of the links and the install later.




(edit...) PIX!!!
Image
Image
Image
Image
Image
Image
[/img]
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

User avatar
bigbird
2GN Member
Posts: 572
Joined: Thu Apr 06, 2006 5:00 pm
Location: Oklahoma City, Oklahoma

Post by bigbird » Sat Aug 26, 2006 12:11 am

This is what I will need to do. Where did you get the heim joints?
Image
Everytime it dings someone in your county does a ricer flyby.

Neons are just smart like that... heydockyle

User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Sat Aug 26, 2006 12:18 am

my local bearing shop supplied them for $6.50 a peice... i believe they were a 7/16 hole through the ball and a 7/16 fine thread bolt into the female end.


(edit) And just for the record, i did have to shorten the sleeves that space the bushings from the heim joint... but the flat caps on each end just pop off of the sleeve, then you cut to length, and then pop the cap back on.
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Sat Aug 26, 2006 12:34 am

nicely done, hows it handle now?
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Sat Aug 26, 2006 12:39 am

ummm. honestly i cant tell a whole lot of difference... but i did swap the front bar to a 24mm only last week. I do notice a little more rotation from the rear end under hard braking, but the front still likes to plow. At this moment i am a little unbiased as to wether or not i like it. But a little time on the asphalt will tell.

One thing i am happy with is that i can easily upgrade to a larger rear bar now. The long bolts i used are grade 8 and the heim joints are aircraft grade... so they should handle just about any bar


EDIT
Oh, and just so everyone knows.. in the pics above, the long bolts that go down into the heim joint arent all the way tight. These pics were an in-between install pic. The nut just above the joint is actually used as a lock nut against the joint
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Sat Aug 26, 2006 12:45 am

id suggest some good springs and struts (which eliminate the need for any custom work to mount the rear sway, btw). my suspension mods are starting to pile up, and id say that the drop made the biggest diff, and the rear sway addition was was very effective. my car's pretty stiff now, and the only thing its lacking is tires (which directly relates to what my wallet is lacking :lol: ). after that, its gonna be a beast!
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Sat Aug 26, 2006 12:48 am

i've got 1st gen acr springs on the way...
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Sat Aug 26, 2006 12:52 am

what kinda drop are those good for? not much huh? pick up some good struts and you'll be set bro.
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Sat Aug 26, 2006 1:08 am

i think everyone says around a 1.5 drop all around... i'm not sure. I'll get pics of those when they get in.

Not sure what struts i want, but i'll get to that later.
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

daaboots
2GN Member
Posts: 762
Joined: Wed Mar 22, 2006 8:22 am
Location: Ottawa, ON
Contact:

Post by daaboots » Tue Aug 29, 2006 9:05 pm

Nice! Where did you get those brackets and how much!!!
2005 SX 2.0 - http://www.cardomain.com/ride/2092484
Rear sway bar brackets on sale! - viewtopic.php?t=19840
My Feedback - viewtopic.php?t=10546
Image

User avatar
bigbird
2GN Member
Posts: 572
Joined: Thu Apr 06, 2006 5:00 pm
Location: Oklahoma City, Oklahoma

Post by bigbird » Wed Aug 30, 2006 7:11 am

daaboots wrote:Nice! Where did you get those brackets and how much!!!
http://forum.2gn.org/viewtopic.php?t=11669
Image
Everytime it dings someone in your county does a ricer flyby.

Neons are just smart like that... heydockyle

User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Wed Aug 30, 2006 8:54 am

yeah, the brackets are chrysler. the vitor units are the same shape, but seem to be thicker and don't have a nut already welded to them. This install was actually pretty straight forward after i werked out what parts i would be using.

I guess this would be my close to one week update, everything in the rear is still tight. I did use locktite blue on the bolts that go from the heim joint into the bracket. Just wanted that extra security that they wouldnt be wiggliing out. There is no noticeable noise in the rear, i had expected some because of solidness of the heim joint, but still there is none.

This upgrade made a nice difference in the feel of the car. And it also seems that my braking distance has reduced sine the add of the rear and the front upgrade. I would deffinatley recommend a rear bar for those who dont have one, and an upgrade for those who do.
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

ewetho
2GN Member
Posts: 694
Joined: Sat Jun 10, 2006 5:49 pm
Location: Kankakee, IL
Contact:

Post by ewetho » Fri Sep 08, 2006 11:30 pm

Might think of a larger rear bar to balance out that huge front one. It will make it understeer less.
2004 Neon SE -- Mods -- K&N CAI, R/T Muffler, Booger Bushings, Prothane Suspension & Race MM Inserts, Vitor's TM Inserts

User avatar
kc2005ptgt
Former Moderator
Posts: 6587
Joined: Wed Dec 14, 2005 7:39 pm
Location: Kansas City, MO
Contact:

Post by kc2005ptgt » Mon Feb 05, 2007 10:34 pm

OB wrote:what kinda drop are those good for? (ACR/RT 1gn springs) not much huh?
Actually, take a look at my WWW in my sig, and you will see the difference - was good for about 1-2in
SOLD 5/13- 2005 Chrysler PT Cruiser GT Convertible | 2.4L Turbo HO | Bright Silver Metallic
SOLD 7/09- 2002 Dodge Neon ACR | Flame Red
The Offical: Sold My Neon Even Though I Swore I Never Would Club | Member #777

Image

User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Tue Feb 06, 2007 12:30 am

i got mine put on back on the fall... and i honestly dont think i got 2 inches. Maybe 1.5" up front and 2" in the back.
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

neon2ner
2GN Member
Posts: 689
Joined: Fri Jan 12, 2007 10:24 am
Location: Halifax, NS

Post by neon2ner » Tue Apr 10, 2007 9:36 am

nice work.

lol dude, what movie is that from in your avatar? thats freaking hilarious.
Image
Scott Woodworth
2004 SRT-4
Halifax, Nova Scotia, Canada

Hudson_Neon
2GN Member
Posts: 3371
Joined: Wed Mar 14, 2007 4:50 pm

Post by Hudson_Neon » Tue Apr 10, 2007 4:33 pm

doesn't the heim joint kinda defeat the purpose? i mean isn't a sway bar suposed to stiffen it rear ind up?

User avatar
CA180
2GN Member
Posts: 1172
Joined: Thu Aug 17, 2006 8:51 am
Location: Tulsa, Oklahoma

Post by CA180 » Wed Apr 11, 2007 7:34 pm

Heim joints dont have much if any vertical play. They are stiffer than using stock rubber bushings. A sway bar keeps the car from leaning, not supposed to stiffen it up.

Neon2ner, i found that on another guys avatar on another site. I cant claim responsibility... I just think its funny :-)
Image

Current project... 81 C10 laying rockers
teamliviD wrote:I want another rim job!!!!

ewetho
2GN Member
Posts: 694
Joined: Sat Jun 10, 2006 5:49 pm
Location: Kankakee, IL
Contact:

Post by ewetho » Wed Apr 11, 2007 11:49 pm

Race cars use Heim joints for free motion in the moving parts with NO PLAY. But subject to wear. Polly is another good choice but not as free.
2004 Neon SE -- Mods -- K&N CAI, R/T Muffler, Booger Bushings, Prothane Suspension & Race MM Inserts, Vitor's TM Inserts

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12737
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Tue Jan 22, 2008 1:20 pm

Bump to the top:
4626764 - $13.60msrp NS1 as of Jan 2008 - 12 left in the country
4626725 - $13.60msrp
Those are the numbers for the brackets used in this topic....

neongirl87
2GN Member
Posts: 132
Joined: Sun Feb 23, 2014 9:57 pm

Post by neongirl87 » Sun Jun 29, 2014 9:05 pm

nice write up and pics! =)

i def want this upgrade on my car

valleyracer
n00b
Posts: 21
Joined: Thu Sep 11, 2014 1:23 am

Drooling over heim joint photos

Post by valleyracer » Sun Sep 21, 2014 6:40 am

ewetho wrote:Race cars use Heim joints for free motion in the moving parts with NO PLAY. But subject to wear. Polly is another good choice but not as free.
I know the thread is old, and I won't make anymore rear sway bar upgrades to my ACR, but I would have opted out of using the OEM bushings.

Image

WarnerTok
n00b
Posts: 4
Joined: Thu Dec 27, 2018 1:47 am

Finally got my rear bar on had to DIY PICS

Post by WarnerTok » Wed Jan 16, 2019 8:50 am

Am I right in thinking youve got the 22mm front bar?

Ive boxed in one side of the strut mount on my m.

I was not aware that the m5 had any reinforcement to the struts with its 25mm bar.

Post Reply

Return to “Suspension, Steering & Brakes”