2GN.ORG 2GN.ORG
The best source for the Second Generation Neon - Period.
 
 Watched TopicsWatched Topics   FAQFAQ   RulesBoard Rules   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks  :: Register
 ProfileProfile   GarageGarage   1/4 Mile Table1/4 Mile Table   Log in to check your private messagesLog in to check your private messages   Log inLog in 

How To: remove lash adjuster from SOHC rocker


 
Post new topic   Reply to topic    2GN.ORG Forum Index -> How-To's -> HT Engine
View previous topic :: View next topic  
Author Message
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19835
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #1   PostPosted: Thu Nov 02, 2017 8:06 am    Post subject: How To: remove lash adjuster from SOHC rocker Reply with quote

https://www.youtube.com/watch?time_continue=204&v=0nmZVueqHOs

http://www.rockauto.com/en/catalog/dodge,2002,neon,2.0l+l4,1432877,engine,valve+lifter,5548

Might save a few $$$ over new rockers.

Rock ON Pun intended...
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12712


2002 Dodge Neon R/T

Post: #2   PostPosted: Thu Nov 02, 2017 8:07 pm    Post subject: Reply with quote

After all these years there are finally replacements Rock ON

Nice find!
Back to top
View user's profile Send private message  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19835
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #3   PostPosted: Fri Nov 03, 2017 3:34 am    Post subject: Reply with quote

LOL, thank bcuda1 on neons.org.

They mentioned them on Rockauto. But the manufacturer offers no install instructions, so after searching, I cam across the video. Since the 3.5/4.0 rockers are very similar, and use the same cartridge....
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19835
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #4   PostPosted: Fri Nov 03, 2017 5:59 am    Post subject: Reply with quote

Neons don't have the top hole shown in the video, but Case on the .org may drill a hole in the top, to see if they can be driven out like shown.

The hole in the side is there to bleed air out. The top hole shown in the 3.5 rockers is to manually bleed them, a feature neons don't have. So drilling an added hole should not have an impact on operation.
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
Display posts from previous:   
Post new topic   Reply to topic    2GN.ORG Forum Index -> How-To's -> HT Engine All times are UTC - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by p h p B B © 2001, 2005 p h p B B Group
2GN.org Decals