2GN.ORG 2GN.ORG
The best source for the Second Generation Neon - Period.
 
 Watched TopicsWatched Topics   FAQFAQ   RulesBoard Rules   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks  :: Register
 ProfileProfile   GarageGarage   1/4 Mile Table1/4 Mile Table   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Part Number Request: subframe nut/bolt?


 
Post new topic   Reply to topic    2GN.ORG Forum Index -> Part Numbers -> PN Chassis
View previous topic :: View next topic  
Author Message
sidepipe87
boom! roasted!
2009 Silver Contributor


Age: 30
Joined: 30 May 2008
Posts: 9595
Location: Pittsburgh, PA

2003 Dodge Neon SXT

Post: #1   PostPosted: Thu Mar 01, 2012 9:25 am    Post subject: Part Number Request: subframe nut/bolt? Reply with quote

Not sure that there will be a PN for this since it is part of the frame it seems but it's worth a shot...

I took my K-frame off my silver car to get it PC'd, and when I did one of the 4 bolts that holds it up gave me a lot of grief. The rear driver's side bolt was rusted to oblivion and wouldn't come out without a fight. Now that nut is in the frame rail and there is a little opening in the frame where you can peek in. The nut was like the vertical LCA bolt in that it is welded to a tab so that it doesn't spin... Welll, with as rusty as it was that tab eventually sliced right through the frame rail and would now just spin. Long story short, I tried vice grips to hold the tab and work the bolt out... no dice. Ended up grinding the bolt head off.

I'm curious if I can buy that nut with the tab welded on (will easily slip through the hole in the frame now...) as well as the bolt for it. I can't seem to find the hardware from the SRT or I'd use it.

I guess my other options are fish it out, drill out the bolt, thread chase it, flatten it back out and reuse it or just use a nut and try to hold it with a wrench.

Hoping this is something I can just buy from the dealer
Back to top
View user's profile Send private message  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #2   PostPosted: Thu Mar 01, 2012 9:37 am    Post subject: Reply with quote

Yes the nut is available. I will try to get you a PN a little later.
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
sidepipe87
boom! roasted!
2009 Silver Contributor


Age: 30
Joined: 30 May 2008
Posts: 9595
Location: Pittsburgh, PA

2003 Dodge Neon SXT

Post: #3   PostPosted: Thu Mar 01, 2012 9:54 am    Post subject: Reply with quote

You're amazing... Maybe a number for the bolt as well? Laughing
_________________
PM me for your 03+ PCM SKIM/VIN flashing needs.
Back to top
View user's profile Send private message  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #4   PostPosted: Thu Mar 01, 2012 11:57 am    Post subject: Reply with quote

6505595AA NUT, M14X2

6506038AA SCREW, Hex Head, Cross Member To Side Rail

I replaced all of them when I did the replacement crossmemeber.

Just to complete the set...

6506039AA SCREW, Hex Head, Front Control Arm Rear Pivot Att M16x2.00x130.0
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
sidepipe87
boom! roasted!
2009 Silver Contributor


Age: 30
Joined: 30 May 2008
Posts: 9595
Location: Pittsburgh, PA

2003 Dodge Neon SXT

Post: #5   PostPosted: Thu Mar 01, 2012 2:02 pm    Post subject: Reply with quote

You're the man, OD! thumbup
_________________
PM me for your 03+ PCM SKIM/VIN flashing needs.
Back to top
View user's profile Send private message  
Midnight_Rider
2014 Platinum Contributor


Age: 58
Joined: 01 Aug 2006
Posts: 7991




Post: #6   PostPosted: Tue Mar 26, 2013 7:40 pm    Post subject: Reply with quote

I don't know how I missed this. I'll have to file this thread for future reference. thumbup
Back to top
View user's profile Send private message  
NickKo
2009 Gold Contributor


Age: 52
Joined: 11 Jun 2006
Posts: 2421
Location: IL./WI.border



Post: #7   PostPosted: Sat Mar 30, 2013 7:14 am    Post subject: Reply with quote

Midnight_Rider wrote:
I don't know how I missed this. I'll have to file this thread for future reference. thumbup

I don't know how I missed this, either. withstupid


- Nick
_________________
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-1999 4-dr DOHC ATX= UDP, Kirk Intake
-2000 Ply.LX with MTX = Maddog STS; CAI; 2.5 in. exhaust
-2001 Ddg. ES with ATX = UDP and Magnum header...Syked PCM 'pending'.

Official "I'm Going to Drive My Neon till it Dies" Club #000009
Back to top
View user's profile Send private message Send e-mail MSN Messenger AIM Address Yahoo Messenger
nerox
2011 Silver Contributor


Age: 29
Joined: 20 Dec 2009
Posts: 939
Location: United Kingdom

2001 Chrysler Neon R/T

Post: #8   PostPosted: Sat Jun 29, 2013 1:42 pm    Post subject: Reply with quote

I found the part number for the 2x bolts to hold the PS cooler to the subframe:

6505911AA

my dealer wants $5 each ??!!

does anyone know / can find out the thread size & length of these so i can get some from hardware store for $0.50 ?

thumbup
_________________
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Back to top
View user's profile Send private message Send e-mail MSN Messenger  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #9   PostPosted: Sun Jun 30, 2013 8:53 am    Post subject: Reply with quote

M6 x 1.00, 15 to 25 mm long should be adequate.

You are paying for the captive washer design of the screw. Even if you can find those at a hardware, you are going to pay a premium for them.

Heck most smaller hardware stores here rip you a buck or more over, for the equivalent metric screw over a standard one. (Say a 13mm size vs a 1/2" size)
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
nerox
2011 Silver Contributor


Age: 29
Joined: 20 Dec 2009
Posts: 939
Location: United Kingdom

2001 Chrysler Neon R/T

Post: #10   PostPosted: Sun Jun 30, 2013 11:19 am    Post subject: Reply with quote

occasional demons wrote:
M6 x 1.00, 15 to 25 mm long should be adequate.

You are paying for the captive washer design of the screw. Even if you can find those at a hardware, you are going to pay a premium for them.

Heck most smaller hardware stores here rip you a buck or more over, for the equivalent metric screw over a standard one. (Say a 13mm size vs a 1/2" size)


Thanks for that thumbup

they charge a premium for metric? hmm its pretty much impossible for us to find imperial in Europe.

just checked my local shop: M6x1.00x30 (a2) = 18c each
_________________
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Back to top
View user's profile Send private message Send e-mail MSN Messenger  
titansxt
Go post count!
2GN Registrant


Age: 31
Joined: 12 May 2004
Posts: 2861
Location: IL



Post: #11   PostPosted: Sun Jul 19, 2015 7:25 pm    Post subject: Reply with quote

occasional demons wrote:
6505595AA NUT, M14X2

6506038AA SCREW, Hex Head, Cross Member To Side Rail

I replaced all of them when I did the replacement crossmemeber.

Just to complete the set...

6506039AA SCREW, Hex Head, Front Control Arm Rear Pivot Att M16x2.00x130.0


Just to confirm, these are the only nuts and bolts that should be replaced if you're replacing the crossmember? I'm having a difficult time trying to decipher the parts catalog picture.
_________________

2003 SXT
2005 SRT-4
2gn.org member #26 tard
Lemon Neon member #1.
Any or all of the above statement(s) may be entirely fictional and a fabrication. Laughing
ram50rocket wrote:

I must had been mistaken in thinking that NEONS.ORG was just for neons.
Back to top
View user's profile Send private message  
Midnight_Rider
2014 Platinum Contributor


Age: 58
Joined: 01 Aug 2006
Posts: 7991




Post: #12   PostPosted: Sun Jul 19, 2015 9:43 pm    Post subject: Reply with quote

Here is what I bought for replacing my K-frame and front lower control arms (directly from the dealership invoice)- I hope that this helps.

Quantity Part No. Description List

2 6506038AA SCREW-HEX 6.50
2 6505595AA NUT 7.70
2 6506039AA SCREW-HEX 10.00
2 6505595AA NUT 7.70
2 6506038AA SCREW-HEX 6.50
2 6505595AA NUT 7.70
2 6504742 SCREW-HEX 7.70
2 6501248 BOLT-HEX F 4.95
2 6501247 NUT 4.45

I know that some parts are on the list twice but this is how my dealership ordered them.
Back to top
View user's profile Send private message  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #13   PostPosted: Mon Nov 06, 2017 5:02 am    Post subject: Reply with quote

6506039AA vertical LCA bolt now $34.00 each.
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
Display posts from previous:   
Post new topic   Reply to topic    2GN.ORG Forum Index -> Part Numbers -> PN Chassis All times are UTC - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by p h p B B © 2001, 2005 p h p B B Group
2GN.org Decals
East Coast Neons