2GN.ORG 2GN.ORG
The best source for the Second Generation Neon - Period.
 
 Watched TopicsWatched Topics   FAQFAQ   RulesBoard Rules   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   LinksLinks  :: Register
 ProfileProfile   GarageGarage   1/4 Mile Table1/4 Mile Table   Log in to check your private messagesLog in to check your private messages   Log inLog in 

00-02 Engine Codes

Goto page 1, 2  Next
 
Post new topic   Reply to topic    2GN.ORG Forum Index -> Engine
View previous topic :: View next topic  
Author Message
grindpunk16
Faster than Richard
2GN Registrant


Age: 32
Joined: 12 May 2004
Posts: 825
Location: St. Pete



Post: #1   PostPosted: Wed Jul 21, 2004 8:08 pm    Post subject: 00-02 Engine Codes Reply with quote

DIAGNOSTIC TROUBLE CODE DESCRIPTIONS P-code suffixes
(M) Check Engine Lamp (MIL) will illuminate during engine operation if this Diagnostic Trouble Code was recorded.
(G) Generator Lamp Illuminated within 5 seconds.
GENERIC SCAN TOOL CODE DRB SCAN TOOL DISPLAY DESCRIPTION OF DIAGNOSTIC TROUBLE CODE
P0030 1/1 02 Sensor Heater Relay Malfunction
P0036 112 02 Sensor Heater Relay Malfunction
P0106(M) Barometric Pressure Out of Range MAP sensor input voltage out of an acceptable range detected during reading of barometric pressure at key-on.
P0107(M) Map Sensor Voltage Too Low MAP sensor input below minimum acceptable voltage.
P0108(M) Map Sensor Voltage Too High MAP sensor input above maximum acceptable voltage.
P0112(M) Intake Air Temp Sensor Voltage Low Intake air (charge) temperature sensor input below the minimum acceptable voltage.
P0113(M) Intake Air Temp Sensor Voltage High Intake air (charge) temperature sensor input above the maximum acceptable voltage.
P0116 Coolant Temp. Sensor Performance A rationality error has been detected in the coolant temp sensor
P0117(M) ECT Sensor Voltage Too Low Engine coolant temperature sensor input below the minimum acceptable voltage
P0118(M) ECT Sensor Voltage Too High Engine coolant temperature sensor input above the maximum acceptable voltage
P0121(M) TPS Voltage Does Not Agree With MAP TPS signal does not correlate to MAP sensor signal.
P0122(M) Throttle Position Sensor Voltage Low Throttle position sensor input below the acceptable voltage range
P0123(M) Throttle Position Sensor Voltage Throttle position sensor input above the maximum High acceptable voltage
P0125(M) Closed Loop Temp Not Reached Time to enter Closed Loop Operation (Fuel Control) is excessive
P0130 1/1 02 Sensor Heater Relay Malfunction
P0131(M) 1/1 02 Sensor Shorted To Ground Oxygen sensor input voltage maintained below normal operating range
P0030 1/1 02 Sensor Heater Relay Malfunction
P0036 112 02 Sensor Heater Relay Malfunction
P0106(M) Barometric Pressure Out of Range MAP sensor input voltage out of an acceptable range detected during reading of barometric pressure at key-on.
P0107(M) Map Sensor Voltage Too Low MAP sensor input below minimum acceptable voltage.
P0108(M) Map Sensor Voltage Too High MAP sensor input above maximum acceptable voltage.
P0112(M) Intake Air Temp Sensor Voltage Low Intake air (charge) temperature sensor input below the minimum acceptable voltage.
P0113(M) Intake Air Temp Sensor Voltage High Intake air (charge) temperature sensor input above the maximum acceptable voltage.
P0116 Coolant Temp. Sensor Performance A rationality error has been detected in the coolant temp sensor
P0117(M) ECT Sensor Voltage Too Low Engine coolant temperature sensor input below the minimum acceptable voltage
P0118(M) ECT Sensor Voltage Too High Engine coolant temperature sensor input above the maximum acceptable voltage
P0121(M) TPS Voltage Does Not Agree With MAP TPS signal does not correlate to MAP sensor signal.
P0122(M) Throttle Position Sensor Voltage Low Throttle position sensor input below the acceptable voltage range
P0123(M) Throttle Position Sensor Voltage Throttle position sensor input above the maximum High acceptable voltage
P0125(M) Closed Loop Temp Not Reached Time to enter Closed Loop Operation (Fuel Control) is excessive
P0130 1/1 02 Sensor Heater Relay Malfunction
P0131(M) 1/1 02 Sensor Shorted To Ground Oxygen sensor input voltage maintained below normal operating range
P0141 1/1 02 Sensor Relay Oxygen sensor relay bad
P0147 1/3 02 Sensor Heater Failure Oxygen sensor heater element malfunction.
P0151(M) 2/1 02 Sensor Shorted To Ground Oxygen sensor input voltage maintained below normal operating range
P0152(M) 2/1 02 Sensor Shorted To Voltage Oxygen sensor input voltage sustained above normal operating range
P0153(M) 2/1 02 Sensor Slow Response Oxygen sensor response slower than minimum required switching frequency
P0154(M) 2/1 02 Sensor Stays at Center Neither rich or lean condition is detected from the oxygen sensor
P0155(M) 2/1 02 Sensor Heater Failure Oxygen sensor heater element malfunction.
P0157(M) 2/2 02 Sensor Shorted To Ground Oxygen sensor input voltage maintained below normal operating range
P0158(M) 2/2 02 Sensor Shorted To Voltage Oxygen sensor input voltage maintained above normal operating range
P0159 2/2 02 Sensor Slow Response Oxygen sensor response slower than minimum required switching frequency
P0160(M) 2/2 02 Sensor Stays at Center Neither rich nor lean condition is detected from the oxygen sensor.
P0161(M) 2/2 02 Sensor Heater Failure Oxygen sensor heater element malfunction.
P0171(M) 1/1 Fuel System Lean A lean air/fuel mixture has been indicated by an abnormally rich correction factor.
P0172(M) 1/1 Fuel System Rich A rich air/fuel mixture has been indicated by an abnormally lean correction factor.
P0174(M) 211 Fuel System Lean A lean air/fuel mixture has been indicated by an abnormally rich correction factor.
P0175(M) 211 Fuel System Rich A rich air/fuel mixture has been indicated by an abnormally lean correction factor.
P0176 Loss of Flex Fuel Calibration Signal No calibration voltage present from flex fuel sensor
P0178 Flex Fuel Sensor Volts Too Low Flex fuel sensor input below minimum acceptable voltage.
P0179 Flex Fuel Sensor Volts Too High Flex fuel sensor input above maximum acceptable voltage.
P0182 CNG Temp Sensor Voltage Too Low Compressed natural gas temperature sensor voltage below acceptable voltage.
P0183 CNG Temp Sensor Voltage Too High Compressed natural gas temperature sensor voltage above acceptable voltage.
P0201(M) Injector #1 Control Circuit An open or shorted condition detected in control circuit for injector #1 or the INJ 1 injector bank.
P0202(M) Injector #2 Control Circuit An open or shorted condition detected in control circuit for injector #2 or the INJ 2 injector bank.
P0203(M) Injector #3 Control Circuit An open or shorted condition detected in control circuit for injector #3 or the INJ 3 injector bank.
P0204(M) Injector #4 Control Circuit Injector #4 or INJ 4 injector bank output driver stage does not respond properly to the control signal.
P0205(M) Injector #5 Control Circuit Injector #5 output driver stage does not respond properly to the control signal.
P0206(M) Injector #6 Control Circuit Injector #6 output driver stage does not respond properly to the control signal.
P0207 Injector #7 Control Circuit Injector #7 output driver stage does not respond properly to the control signal.
P0208 Injector #8 Control Circuit Injector #8 output driver stage does not respond properly to the control signal.
P0209 Injector #9 Control Circuit Injector #9 output driver stage does not respond properly to the control signal.
P0210 Injector #10 Control Circuit Injector #10 output driver stage does not respond properly to the control signal.
P0300(M) Multiple Cylinder Misfire Misfire detected in multiple cylinders.
P0301(M) CYLINDER #1 MISFIRE Misfire detected in cylinder #1.
P0302(M) CYLINDER #2 MISFIRE Misfire detected in cylinder #2.
P0303(M) CYLINDER #3 MISFIRE Misfire detected in cylinder #3.
P0304(M) CYLINDER #4 MISFIRE Misfire detected in cylinder #4.
P0305(M) CYLINDER #5 MISFIRE Misfire detected in cylinder #5.
P0306(M) CYLINDER #6 MISFIRE Misfire detected in cylinder #6.
P0307(M) CYLINDER #7 MISFIRE Misfire detected in cylinder #7
P0308(M) CYLINDER #8 MISFIRE Misfire detected in cylinder #8.
P0309(M) CYLINDER #9 MISFIRE Misfire detected in cylinder #9.
P031 0(M) CYLINDER #10 MISFIRE Misfire detected in cylinder #10.
P0320 No Crank Reference Signal at PCM No reference signal (crankshaft position sensor) detected during engine cranking.
P0325 Knock Sensor #1 Circuit Knock sensor (#1) signal above or below minimum acceptable threshold voltage at particular engine speeds.
P0330 Knock Sensor #2 Circuit Knock sensor (#2) signal above or below minimum acceptable threshold voltage at particular engine speeds.
P0340(M) No Cam Signal At PCM No fuel sync
P0350 Ignition Coil Draws Too Much Current A coil (1 -5) is drawing too much current.
P0351(M) Ignition Coil # 1 Primary Circuit Peak primary circuit current not achieved with maximum dwell time.
P0352(M) Ignition Coil # 2 Primary Circuit Peak primary circuit current not achieved with maximum dwell time.
P0353(M) Ignition Coil # 3 Primary Circuit Peak primary circuit current not achieved with maximum dwell time.
P0354(M) Ignition Coil # 4 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High Impedance).
P0355(M) Ignition Coil # 5 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High Impedance).
P0356(M) Ignition Coil # 6 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High impedance).
P0357 Ignition Coil # 7 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High impedance).
P0358 Ignition Coil # 8 Primary Circuit Peak primary circuit current not achieved with maximum dwell time (High impedance).
P0401(M) EGR System Failure Required change in air/fuel ration not detected during diagnostic test.
P0403(M) EGR Solenoid Circuit An open or shorted condition detected in the EGR solenoid control circuit.
P0404(M) EGR Position Sensor Rationality EGR position sensor signal does not correlate to EGR duty cycle.
P0405(M) EGR Position Sensor Volts Too Low EGR position sensor input below the acceptable voltage range.
P0406(M) EGR Position Sensor Volts Too High EGR position sensor input above the acceptable voltage range.
P0412 Secondary Air Solenoid Circuit An open or shorted condition detected in the secondary air (air switching/aspirator) solenoid control circuit.
P0420(M) 1/1 Catalytic Converter Efficiency Catalyst 1/1 efficiency below required level.
P0432(M) 112 Catalytic Converter Efficiency Catalyst 211 efficiency below required level.
P0441(M) Evap Purge Flow Monitor Insufficient or excessive vapor flow detected during evaporative emission system operation.
P0442(M) Evap Leak Monitor Medium (0.040) Leak Detected A small leak has been detected in the evaporative system
P0443(M) Evap Purge Solenoid Circuit An open or shorted condition detected in the EVAP purge solenoid control circuit.
P0455(M) Evap Leak Monitor Large Leak Detected A large leak has been detected in the evaporative system.
P0456 Evap Leak Monitor Small (0.020) Leak Detected A small leak has been detected in the evaporative system
P0460 Fuel Level Unit No Change Over Miles No movement of fuel level sender detected.
P0461 Fuel Level Unit No Changeover Time No level of fuel level sender detected.
P0462 Fuel Level Sending Unit Volts Too Low Fuel level sensor input below acceptable voltage.
P0463 Fuel Level Sending Unit Volts Too High Fuel level sensor input above acceptable voltage.
P0500(M) No Vehicle Speed Sensor Signal No vehicle speed sensor signal detected during road load conditions.
P0505(M) Idle Air Control Motor Circuits Actual state of AIS motor not equal to desired state.
P0522 Oil Pressure Sens Low Oil pressure sensor input below acceptable voltage.
P0523 Oil Pressure Sens High Oil pressure sensor input above acceptable voltage.
P0551(M) Power Steering Switch Failure Incorrect input state detected for the power steering switch circuit. PL: High pressure seen at high speed.
P0600(M) PCM Failure SPI Communications No communication detected between co-processors in the control module.
P0601(M) PCM Internal Controller Failure Internal control module fault condition (check sum) detected.
P0604 RAM Check Failure Transmission control module RAM self test fault detected. -Aisin transmission.
P0605 ROM Check Failure Transmission control module ROM self-test fault detected -Aisin transmission.
P0615 Starter Relay Control Circuit An open or shorted condition detected in the starter relay control circuit.
P0622 (G) Generator Field Not Switching Properly An open or shorted condition detected in the generator field control circuit
P0645 A/C Clutch Relay Circuit An open or shorted condition detected in the A/C clutch relay control circuit.
P0700(M) EATX Controller DTC Present This SBEC III or JTEC DTC indicates that the EATX or Aisin controller has an active fault and has illuminated the MIL via a J1850 (EATX) or SCI (Aisin) message. The specific fault must be acquired from the EATX via J1850 or from the Aisin via ISO-9141.
P0703(M) Brake Switch Sense Circuit Incorrect input state detected in the brake switch circuit. (Changed from P1595).
P0711 Trans Temp Sensor, No Temp Rise After Start Relationship between the transmission temperature and overdrive operation and/or TCC operation indicates a failure of the Transmission Temperature Sensor. OBD 11 Rationality.
P0712 Trans Temp Sensor Voltage Too Low Transmission fluid temperature sensor input below acceptable voltage.
P0713 Trans Temp Sensor Voltage Too High Transmission fluid temperature sensor input above acceptable voltage.
P0720 Low Output SPD Sensor RPM, Above 15 MPH The relationship between the Output Shaft Speed Sensor and vehicle speed is not within acceptable limits.
P0740(M) Torq Con Clu, No RPM Drop at Lockup Relationship between engine and vehicle speeds indicated failure of torque convertor clutch lock-up system (TCC/PTU sol).
P0743 Torque Converter Clutch Solenoid/ Trans Relay Circuits An open or shorted condition detected in the torque converter clutch (part throttle unlock) solenoid control circuit. Shift solenoid C electrical fault - Aisin transmission
P0748 Governor Pressure Sol Control/Trans Relay Circuits An open or shorted condition detected in the Governor Pressure Solenoid circuit or Trans Relay Circuit in JTEC RE transmissions.
P0751 O/D Switch Pressed (Low) More Than 5 Minutes Overdrive override switch input is in a prolonged depressed state.
P0753 Trans 3-4 Shift Sol/Trans Relay Circuits An open or shorted condition detected in the overdrive solenoid control circuit or Trans Relay Circuit in JTEC RE transmissions.
P0756 AW4 Shift Sol B (2-3) Functional Failure Shift solenoid B (2-3) functional fault - Aisin transmission
P0783 3-4 Shift Sol, No RPM Drop at Lockup The overdrive solenoid is unable to engage the gear change from 3rd gear to the overdrive gear.
P0801 Reverse Gear Lockout Circuit Open or Short An open or shorted condition detected in the transmission reverse gear lockout solenoid control circuit.
P0833 Clutch Released Switch Circuit
P01192 Inlet Air Temp. Sensor Voltage Low Inlet Air Temp. sensor input below acceptable voltage
P01193 Inlet Air Temp. Voltage High Inlet Air Temp. sensor input above acceptable voltage
P1194 02 Heater Performance
P1195(M) 1/1 02 Sensor Slow During Catalyst Monitor A slow switching oxygen sensor has been detected in bank 1/1 during catalyst monitor test. (was P0133)
P1196(M) 2/1 02 Sensor Slow During Catalyst Monitor A slow switching oxygen sensor has been detected in bank 2/1 during catalyst monitor test. (was P0153)
P1197 1/2 02 Sensor Slow During Catalyst Monitor A slow switching oxygen sensor has been detected in bank 1/2 during catalyst monitor test. (was P0139)
P1198 Radiator Temperature Sensor Volts Too High Radiator coolant temperature sensor input above the maximum acceptable voltage.
P1199 Radiator Temperature Sensor Volts Too Low Radiator coolant temperature sensor input below the minimum acceptable voltage
P1281 Engine is Cold Too Long Engine coolant temperature remains below normal operating temperatures during vehicle travel (Thermostat).
P1282 Fuel Pump Relay Control Circuit An open or shorted condition detected in the fuel pump relay control circuit.
P1288 Intake Manifold Short Runner Solenoid Circuit An open or shorted condition detected in the short runner tuning valve circuit
P1289 Manifold Tune Valve Solenoid Circuit An open or shorted condition detected in the manifold tuning valve solenoid control circuit.
P1290 CNG Fuel System Pressure Too High Compressed natural gas system pressure above normal operating range
P1291 No Temp Rise Seen From Intake Heaters Energizing Heated Air Intake does not change intake air temperature sensor an acceptable amount.
P1292 CNG Pressure Sensor Voltage Too High Compressed natural gas pressure sensor reading above acceptable voltage
P1293 CNG Pressure Sensor Voltage Too Low Compressed natural gas pressure sensor reading below acceptable voltage
P1294(M) Target Idle Not Reached Target RPM not achieved during drive idle condition. Possible vacuum leak or IAC (AIS) lost steps.
P1295 No 5 Volts to TP Sensor Loss of a 5 volt feed to the Throttle Position Sensor has been detected.
P1296 No 5 Volts to MAP Sensor Loss of a 5 volt feed to the MAP Sensor has been detected.
P1297(M) No Change in MAP From Start To Run No difference is recognized between the MAP reading at engine idle and the stored barometric pressure reading.
P1298 Lean Operation at Wide Open Throttle A prolonged lean condition is detected during wide-open Throttle.
P1299(M) Vacuum Leak Found (IAC Fully Seated) MAP Sensor signal does not correlate to Throttle Position Sensor signal. Possible vacuum leak.
P1388 Auto Shutdown Relay Control Circuit An open or shorted condition detected in the ASD or CNG shutoff relay control circuit
P1389 No ASD Relay Output Voltage At PCM No Z1 or Z2 voltage sensed when the auto shutdown relay is energized.
P 1390(M) Timing Belt Skipped 1 Tooth or More Relationshipbetween Cam and Cranksignals notcorrect.
P1391(M) Intermittent Loss of CMP or CKP Loss of the Cam Position Sensor or Crank Position sensor has occurred.
P1398(M) Misfire Adaptive Numerator at Limit PCM is unable to learn the Crank Sensor's signal in preparation for Misfire Diagnostics. Probable defective Crank Sensor.
P1399 Wait To Start Lamp Circuit An open or shorted condition detected in the Wait to Start Lamp circuit.
P1403 No 5 Volts to EGR Sensor Loss of 5v feed to the EGR position sensor.
P1476 Too Little Secondary Air Insufficient flow of secondary air injection detected during aspirator test.(was P0411)
P1477 Too Much Secondary Air Excessive flow of secondary air injection detected during aspirator test (was P0411).
P1478(M) Battery Temp Sensor Volts Out of Limit Internal temperature sensor input voltage out of an acceptable range.
P1479 Transmission Fan Relay Circuit An open or shorted condition detected in the transmission fan relay circuit.
P1480 PCV Solenoid Circuit An open or shorted condition detected in the PCV solenoid circuit.
P1481 EATX Misfire RPM Signal out of Range EATX RPM pulse generator signal for misfire detection does not correlate with expected value.
P1482 Catalyst Temperature Sensor Circuit Shorted Low Catalyst temperature sensor circuit shorted low.
P1483 Catalyst Temperature Sensor Circuit Shorted High Catalyst temperature sensor circuit shorted high.
P1484 Catalytic Converter Overheat Detected A catalyst overheat condition has been detected by the catalyst temperature sensor.
P1485 Air Injection Solenoid Circuit An open or shorted condition detected in the air assist solenoid circuit.
P1486(M) Eva Leak Monitor Pinched Hose Found LDP has detected a pinched hose in the evaporative hose system.
P1487 Hi Speed Rad Fan CTRL Relay Circuit An open or shorted condition detected in the control circuit of the #2 high-speed radiator fan control relay.
P1488 Auxiliary 5 Volt Supply Output Too Low Auxiliary 5-volt sensor feed is sensed to be below an acceptable limit.
P1489(M) High Speed Fan CTRL Relay Circuit An open or shorted condition detected in the control circuit of the high-speed radiator fan control relay.
P1490(M) Low Speed Fan CTRL Relay Circuit An open or shorted condition detected in control circuit of the low speed radiator fan control relay.
P1491 Rad Fan Control Relay Circuit An open or shorted condition detected in the radiator fan control relay control circuit. This includes PWM solid state relays.
P1492 (M,G) Ambient/Batt Temp Sen Volts Too High External temperature sensor input above acceptable voltage
P1493 (M,G) Ambient/Batt Temp Sen Volts Too Low External temperature sensor input below acceptable voltage.
P1494(M) Leak Detection Pump Switch or Mechanical Fault Incorrect input state detected for the Leak Detection Pump (LDP) pressure switch.
P1495(M) Leak Detection Pump Solenoid Circuit An open or shorted condition detected in the Leak Detection Pump (LDP) solenoid circuit.
P1496(M) 5 Volt Supply, Output Too Low 5-volt sensor feed is sensed to be below an acceptable limit. (< 4v for 4 sec).
P1498 High Speed Rad Fan Ground CTRL Relay Circuit An open or shorted condition detected in the control circuit of the #3 high-speed radiator fan control relay.
P1594 (G) Charging System Voltage Too High Battery voltage sense input above target charging voltage during engine operation.
P1595 Speed Control Solenoid Circuits An open or shorted condition detected in either of the speed control vacuum or vent solenoid control circuits.
P1596 Speed Control Switch Always High Speed control switch input above maximum acceptable voltage.
P1597 Speed Control Switch Always Low Speed control switch input below minimum acceptable voltage.
P1598 A/C Pressure Sensor Volts Too High A/C pressure sensor input above maximum acceptable voltage.
P1599 A/C Pressure Sensor Volts Too Low A/C pressure sensor input below minimum acceptable voltage.
P1602 PCM Not Programmed For generic modules
P1681 No I/P Cluster CCD/J1850 Messages Received No J1850 messages received from the cluster control module.
P1682 (G) Charging System Voltage Too Low Battery voltage sense input below target charging voltage during engine operation and no significant change in voltage detected during active test of generator output circuit.
P1683 SPD CTRL PWR Relay; or S/C 12v Driver CKT An open or shorted condition detected in the speed control servo power control circuit. (SBECII: ext relay).
P1684 Battery Disconnected in the last 50 Starts The battery has been disconnected within the last 50 starts.
P1685 Skim Invalid Key The engine controller has received an invalid key from the SKIM.
P1686 No SKIM BUS Messages Received No J1850 messages received from the Smart Key Immobilizer Module (SKIM).
P1687 No Cluster BUS Message No J1850 messages received from the Mechanical Instrument Cluster (MIC) module.
P1 693 DTC Detected in Companion Module A fault has been generated in the companion engine control module.
P1694 No BUS Message Received from Companion Module No J1850 messages received from the powertrain control module-Aisin transmission.
P1695 No CCD/J1850 Messages from the Body Control Module. No J1850 messages received from the body control module.
P1696(M) PCM Failure EEPROM Write Denied Unsuccessful attempt to write to an EEPROM location by the control module.
P1697(M) PCM Failure SRI Mile Not Stored Unsuccessful attempt to update Service Reminder Indicator (SRI or EMR) mileage in the control module EEPROM.
P1698(M) No CCD/J1850 Message From TCM No J1850 messages received from the electronic transmission control module (EATX) or the Aisin transmission controller.
P1719 Skip Shift Solenoid Circuit An open or shorted condition detected in the transmission 2-3 gear lockout solenoid control circuit.
P1740 TCC or O/D Solenoid Performance A rationality error has been detected in either the tcc solenoid or overdrive solenoid systems.
P1756 GOV Press Not Equal to Target @ not15-20 PSI The requested pressure and the actual pressure are within a tolerance band for the Governor Control System which is used to regulate governor pressure to control shifts for 1st, 2nd, and 3rd gear. (Mid Pressure Malfunction)
P1757 GOV Press Above 3 PSI in gear with 0 MPH The requested pressure and the actual pressure are not within a tolerance band for the Governor Control System which is used to regulate governor pressure to control shifts for 1st, 2nd, and 3rd gear (Zero Pressure Malfunction)
P1762 Gov Press Sen Offset Volts Too Low or High The Governor Pressure Sensor input is greater than a calibration limit or is less than a calibration limit for 3 consecutive park/neutral calibrations.
P1763 Governor Pressure Sensor Volts Too High The Governor Pressure Sensor input is above an acceptable voltage level.
P1764 Governor Pressure Sensor Volts Too Low The Governor Pressure Sensor input is below an acceptable voltage level.
P1765 Trans 12 Volt Supply Relay CTRL Circuit An open or shorted condition is detected in the Transmission Relay control circuit. This relay supplies power to the TCC>
P1899(M) P/N Switch Stuck in Park or in Gear Incorrect input state detected for the Park/Neutral switch.
_________________


^^^^
Michael vs Prince fights

We all know who won

To slow for you Forum member #001

[quote="lambostealth"]Please ditch the lip, pretty please, makes baby jesus cry... Crying or Very sad [/quote]
Back to top
View user's profile Send private message Send e-mail AIM Address
SOLOW SXT
Team Elite Concepts
2GN Registrant


Age: 32
Joined: 23 Jun 2004
Posts: 61
Location: Orlando FL



Post: #2   PostPosted: Tue Aug 31, 2004 5:33 pm    Post subject: Reply with quote

what can be done to fix an P0700?
or can some one translate that to english for me hehe sry
-al
thanks!
_________________
02' Silver SXT
Skunk 2 lowering springs
Apexi N1 axle-back exhaust
Custom intake w breather
Ported n Polished intake Mani and TB
03-05 SXT rims/tires
mesh upper grille
Sunpro A/F ratio gauge/single pillar pod
Remote driving/fog lights
audio and more...
Sponsored by OFL-Motorsports
Ghost Roadsters and Wheels R Us
Back to top
View user's profile Send private message  
Kernel Panic
Got NAAAAWS?
2GN Registrant


Age: 54
Joined: 12 May 2004
Posts: 678
Location: Sunny Vale Trailer Park


ICQ Status:

Post: #3   PostPosted: Wed Sep 01, 2004 7:45 am    Post subject: Reply with quote

SOLOW SXT wrote:
what can be done to fix an P0700?
or can some one translate that to english for me hehe sry
-al
thanks!


Sounds like the TCM(Transmission control module) picked up a fault. You'll need the DRB-III tool to get the full fault code. Crying or Very sad
_________________
The weasels are closing in, I can smell the ugly brutes..
When the going gets wierd, the wierd turn pro.. - Dr. Hunter S. Thompson (1937-2005)

Greg
2001 Magnum equipped Neon ES
My website
Back to top
View user's profile Send private message Visit poster's website AIM Address
01neonrtblk
2GN Registrant


Age: 32
Joined: 08 Nov 2004
Posts: 360
Location: Hanover Park, Illinois



Post: #4   PostPosted: Sat Dec 25, 2004 3:55 pm    Post subject: Reply with quote

i couldnt find the meaning for a p0139 and p0140.

what do they mean???
_________________
2001 Dodge Neon SR/T-4
Back to top
View user's profile Send private message Send e-mail MSN Messenger  
MountainMan
n00b


Age: 44
Joined: 29 Mar 2005
Posts: 5




Post: #5   PostPosted: Tue Mar 29, 2005 1:40 pm    Post subject: Reset Reply with quote

How do you reset a code to blank after fixing it?

I installed a new throttle body and forgot to plug in one sensor. t sent a code and now my check engine light comes on. It is code P0508.

I want to clear it

Any ideas
Back to top
View user's profile Send private message  
Diablo0
Bird is the word
2GN.org Owner/Admin


Age: 33
Joined: 15 Apr 2004
Posts: 12432
Location: Greenville, SC

2002 Dodge Neon R/T

Post: #6   PostPosted: Tue Mar 29, 2005 1:42 pm    Post subject: Reply with quote

Disconnect the battery then reconnect it.
_________________
-Jason
Black '02 Neon R/T | White '02 Neon R/T - SRT-4 Engine Swap

^^^ no, that isn't what I look like haha
Try not to become a man of success but rather to become a man of value. - Albert Einstein
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger AIM Address Yahoo Messenger
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12711


2002 Dodge Neon R/T

Post: #7   PostPosted: Sun Oct 02, 2005 4:35 am    Post subject: Reply with quote

Disconnect battery AND remove the fuel pump and MTX relay, wait 15min and your set...
Back to top
View user's profile Send private message  
LOOINEY
n00b


Age: 30
Joined: 05 Sep 2005
Posts: 10
Location: Winona, MN



Post: #8   PostPosted: Sun Oct 02, 2005 5:56 am    Post subject: Reply with quote

you can just disconnect the positive and step on the brake for about 10sec. so all the power is drained out of the car then reconect and should be cleared. or if in a big rush try to turn over the engine and that drains it in 1 sec.
Back to top
View user's profile Send private message MSN Messenger  
dblsg
official lurkor-shhh
2GN Registrant


Age: 40
Joined: 02 Jun 2005
Posts: 10719
Location: Aurora, IL

2005 Dodge Neon SXT

Post: #9   PostPosted: Sun Oct 02, 2005 9:36 am    Post subject: Reply with quote

^^ you should always disconnect the negative first.
_________________
Sam-I-Am

Official "I'm Going to Drive My Neon till it Dies" Club #000046
Diablo0 wrote:
"eh... your opinion doesn't matter... I'm doing what I want..."
Back to top
View user's profile Send private message Send e-mail Visit poster's website AIM Address Yahoo Messenger
LOOINEY
n00b


Age: 30
Joined: 05 Sep 2005
Posts: 10
Location: Winona, MN



Post: #10   PostPosted: Mon Oct 03, 2005 2:28 am    Post subject: Reply with quote

Good Point! Kids dont lissen to me.... i live life on the edge Laughing
Back to top
View user's profile Send private message MSN Messenger  
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12711


2002 Dodge Neon R/T

Post: #11   PostPosted: Mon Oct 09, 2006 3:52 pm    Post subject: Reply with quote

LOOINEY wrote:
you can just disconnect the positive and step on the brake for about 10sec. so all the power is drained out of the car then reconect and should be cleared. or if in a big rush try to turn over the engine and that drains it in 1 sec.

For starters.....
I tried this last weekend and it kinda works but does not totally, I used a multi meter to test it...
The fastest result trying to clear codes over the weekend I tried was:
Disconnect the battery ground, turn the ignition on, hit the brake, wait 15sec and you should be fine....I tested this with a multi meter to make sure there was no voltage left and the best I could do was get it down to .01 volts.....

ok now for number 2:
After last weekend I came here to look up a code quick and this post does not have them all, so....


http://diablo.servehttp.com/neonstuff/org/brr/dtc.doc

***EDITED AS OF 11-3-06 PCODES LIST IS NOW A MICROSOFT WORD DOCUMENT TO MAKE DOWNLOADS EASIER***


Last edited by BlackRoseRacing on Fri Nov 03, 2006 1:51 am; edited 2 times in total
Back to top
View user's profile Send private message  
Diablo0
Bird is the word
2GN.org Owner/Admin


Age: 33
Joined: 15 Apr 2004
Posts: 12432
Location: Greenville, SC

2002 Dodge Neon R/T

Post: #12   PostPosted: Mon Oct 09, 2006 4:02 pm    Post subject: Reply with quote

Damn... I was wondering why my internet took a dump there for a sec Laughing
_________________
-Jason
Black '02 Neon R/T | White '02 Neon R/T - SRT-4 Engine Swap

^^^ no, that isn't what I look like haha
Try not to become a man of success but rather to become a man of value. - Albert Einstein
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger AIM Address Yahoo Messenger
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12711


2002 Dodge Neon R/T

Post: #13   PostPosted: Mon Oct 09, 2006 4:26 pm    Post subject: Reply with quote

Laughing
Your server kicked me the first time I was uplaoding the PDF too....

And by the looks of it, the code list covers 2000+ Very Happy


Last edited by BlackRoseRacing on Mon Oct 09, 2006 4:28 pm; edited 1 time in total
Back to top
View user's profile Send private message  
Diablo0
Bird is the word
2GN.org Owner/Admin


Age: 33
Joined: 15 Apr 2004
Posts: 12432
Location: Greenville, SC

2002 Dodge Neon R/T

Post: #14   PostPosted: Mon Oct 09, 2006 4:27 pm    Post subject: Reply with quote

If it wasn't my sever it was the crappy internet the apartment provides that goes down every 3 hours Laughing
_________________
-Jason
Black '02 Neon R/T | White '02 Neon R/T - SRT-4 Engine Swap

^^^ no, that isn't what I look like haha
Try not to become a man of success but rather to become a man of value. - Albert Einstein
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger AIM Address Yahoo Messenger
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12711


2002 Dodge Neon R/T

Post: #15   PostPosted: Mon Oct 09, 2006 4:30 pm    Post subject: Reply with quote

Diablo0 wrote:
If it wasn't my sever it was the crappy internet the apartment provides that goes down every 3 hours Laughing


Im still loving my verizon DSL, Never had a problem with it yet! and half my phone lines in my house are atleast 100years old Laughing
Back to top
View user's profile Send private message  
BlackRoseRacing
1st ever DD SC 2GN!
2009 Platinum Contributor


Age: 38
Joined: 25 Dec 2004
Posts: 12711


2002 Dodge Neon R/T

Post: #16   PostPosted: Fri Nov 03, 2006 1:52 am    Post subject: Reply with quote

A smaller easier to download link is posted above, its in microsoft word...
Back to top
View user's profile Send private message  
Seventhguest
Instigator neon
2GN Registrant


Age: 38
Joined: 19 Jun 2004
Posts: 91
Location: Ghent, Belgium



Post: #17   PostPosted: Wed Dec 06, 2006 9:29 am    Post subject: Reply with quote

P1685 Skim Invalid Key The engine controller has received an invalid key from the SKIM.


I have this one, what does it actually means?
_________________
Back to top
View user's profile Send private message Send e-mail Visit poster's website MSN Messenger  
Blacky
2GN Registrant


Age: 109
Joined: 05 Nov 2006
Posts: 75




Post: #18   PostPosted: Sat Dec 09, 2006 1:20 pm    Post subject: Reply with quote

I have this code on my 2000 neon , P1494(M) Leak Detection Pump Switch or Mechanical Fault Incorrect input state detected for the Leak Detection Pump (LDP) pressure switch , can anyone tell me where to locate this switch so I can get a new one & fix it , thanks ?
Back to top
View user's profile Send private message  
xSEED
2GN Registrant


Age: 33
Joined: 06 Oct 2006
Posts: 151


2001 Dodge Neon ES

Post: #19   PostPosted: Tue Nov 20, 2007 4:07 pm    Post subject: Reply with quote

i got this P0302(M) CYLINDER #2 MISFIRE Misfire detected in cylinder #2.

how do i repair it? it's in pending code section of scanner and it also hesitates alot. changing plugs worked for bout 2 weeks then condition returned
_________________
lo barato sale caro
Back to top
View user's profile Send private message  
Spanky
1gn Bomber Coupe
2GN Registrant


Age: 28
Joined: 01 Jul 2010
Posts: 191
Location: Franklinville,NJ

2001 Dodge Neon R/T

Post: #20   PostPosted: Thu Oct 28, 2010 7:16 pm    Post subject: Reply with quote

My 2001 R/T is now throwing code p 0140 and it is not listed.I am assuming its for an 02 and i am missing one since i hat a LTB Header and no cat.

The engine started ticking and a noise come the cams and i was thinking misfire but no code is thrown for that.

Any thoughts?
_________________


1998 Neon R/T
2005 Neon SRT-D
2010 SCCA Solo Rookie of the Year
Back to top
View user's profile Send private message Visit poster's website AIM Address
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #21   PostPosted: Thu Oct 28, 2010 7:57 pm    Post subject: Reply with quote

Your existing (upstream) is not switching, thus the "no activity" you are prolly not getting the bad catalyst code, because there is not a good signal from the upstream. Could be gong lean, and pinging. I would replace it, and go from there.
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
Spanky
1gn Bomber Coupe
2GN Registrant


Age: 28
Joined: 01 Jul 2010
Posts: 191
Location: Franklinville,NJ

2001 Dodge Neon R/T

Post: #22   PostPosted: Thu Oct 28, 2010 8:09 pm    Post subject: Reply with quote

Ill try that,thank you.The car is un-tuned and im sure it is running lean with all the mods it has currently.
_________________


1998 Neon R/T
2005 Neon SRT-D
2010 SCCA Solo Rookie of the Year
Back to top
View user's profile Send private message Visit poster's website AIM Address
tursh2010
2GN Registrant


Age: 25
Joined: 28 Feb 2012
Posts: 22
Location: Inwood



Post: #23   PostPosted: Thu Mar 08, 2012 7:50 am    Post subject: Reply with quote

I was getting code P0301(M) CYLINDER #1 MISFIRE Misfire detected in cylinder #1 so I replaced my plugs and wires about 2 months ago and it fixed the problem. Then my downstread o2 sensor went bad I fixed that the other day and no check engine light for 4 days, now the check engine light is back on with the code P0301(M) CYLINDER #1 MISFIRE Misfire detected in cylinder #1. What can I do to fix this? I am tired of seeing it.
Back to top
View user's profile Send private message  
Danteneon
Titanium Member
Moderator


Age: 48
Joined: 20 Dec 2007
Posts: 9591
Location: Manassas, VA

2002 Dodge Neon ACR

Post: #24   PostPosted: Thu Mar 08, 2012 8:07 am    Post subject: Reply with quote

What kind of plugs and wires did you replace them with? Is your coil stock? How many miles are on it? Look at the # 1 plug...what is its condition? Are the spark plug tubes not fully seated causing oil to accumulate and keeping the plug from firing correctly?
_________________
If I could just figure out how to meld the Outback and the Neon into one car...

Back to top
View user's profile Send private message Send e-mail  
tursh2010
2GN Registrant


Age: 25
Joined: 28 Feb 2012
Posts: 22
Location: Inwood



Post: #25   PostPosted: Thu Mar 08, 2012 10:12 am    Post subject: Reply with quote

duralast wires, and i cant remember the plugs off the top of my head i think they were autolite but not 100% sure. As far as I know the coil is stock. I was thinking of replacing that but wanted to get other opinions on it first. Everything is in correctly and the plug looks fine. Even when it was misfiring the first time it looked fine but I replaced them anyways to be on safe side.
Back to top
View user's profile Send private message  
Danteneon
Titanium Member
Moderator


Age: 48
Joined: 20 Dec 2007
Posts: 9591
Location: Manassas, VA

2002 Dodge Neon ACR

Post: #26   PostPosted: Thu Mar 08, 2012 10:23 am    Post subject: Reply with quote

FWIW, get a real brand of wires and switch to Champion plugs. Seriously. The Duralast brand is a crapshoot for quality and Autolite plugs are the worst thing to put into a Chrysler engine.

Beyond that, you will need to see if the coil is producing spark reliably to the #1 cylinder.
_________________
If I could just figure out how to meld the Outback and the Neon into one car...

Back to top
View user's profile Send private message Send e-mail  
tursh2010
2GN Registrant


Age: 25
Joined: 28 Feb 2012
Posts: 22
Location: Inwood



Post: #27   PostPosted: Thu Mar 08, 2012 10:31 am    Post subject: Reply with quote

what is a good cheaper brand of wires? and what type of champion plugs I know some places say get copper and others say don't.
Back to top
View user's profile Send private message  
Danteneon
Titanium Member
Moderator


Age: 48
Joined: 20 Dec 2007
Posts: 9591
Location: Manassas, VA

2002 Dodge Neon ACR

Post: #28   PostPosted: Thu Mar 08, 2012 10:45 am    Post subject: Reply with quote

Champion copper plugs are your best bet. As far as wires go, The Blue Streak line of Standard is good, Bosch, BWD/Niehoff, etc.

I may be jaded here, but I don't trust places like Autozone/PepBoys/Advance for car parts. I would rather deal with an actual Auto Parts Store (Napa, APA, Federated, etc.) for parts. Leave the other guys for oil and chemicals.

Totally my opinion BTW.
_________________
If I could just figure out how to meld the Outback and the Neon into one car...

Back to top
View user's profile Send private message Send e-mail  
occasional demons
Mr One World
Moderator


Age: 52
Joined: 03 May 2007
Posts: 19834
Location: Ashland, Ohio

2001 Dodge Neon ES

Post: #29   PostPosted: Thu Mar 08, 2012 12:29 pm    Post subject: Reply with quote

How did this get pulled out of the sticky? Or did it just end up that way when they were linked? Think

http://forum.2gn.org/viewtopic.php?t=57036
_________________
Bill


2001 neon ES MTX with '02 R/T PCM
1999 neon 2.4 EDZ MTX
Help support 2GN!
Back to top
View user's profile Send private message AIM Address
Danteneon
Titanium Member
Moderator


Age: 48
Joined: 20 Dec 2007
Posts: 9591
Location: Manassas, VA

2002 Dodge Neon ACR

Post: #30   PostPosted: Thu Mar 08, 2012 12:33 pm    Post subject: Reply with quote

I think just Quicksilver's post was stickied and not the linked topics. I needs to fix that.
_________________
If I could just figure out how to meld the Outback and the Neon into one car...

Back to top
View user's profile Send private message Send e-mail  
Display posts from previous:   
Post new topic   Reply to topic    2GN.ORG Forum Index -> Engine All times are UTC - 8 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by p h p B B © 2001, 2005 p h p B B Group
2GN.org Decals
East Coast Neons