For those of you not on the .org:
Last night's tuning session:
Weather: Very hot and humid - high 90's.
Dyno: older Dynojet
Engine: 2.4, 10.5:1 CR, Srt-4 rods, ARP hardware, Crower Stage IV cams, Bosch Red Top injectors (don't remember the specs), FastFab header, 1 MM oversize valves, moderate head porting. The CR is low, and the rings gaped loose for NO2 (future use). Fuel is E85.
We ran out of injector at 7,500 RPM, the duty cycle is waaaaay over 100% (130%+). With bigger injectors it may rev higher, we'll see.
Now that the excuses are noted:
That's the .org's own Jon Moore of Moorespeed Performance doing the tuning.
After initial adjustments:
Final:
I'm debating the whole NO2 idea, and going with higher compression, milling the head. Bigger injectors are an immediate need, and a return-type fuel system is a future mod.
Thanks to Jon for getting us to this point. There won't be a test and tune until Aug. 5th at my local track (National Trails). This was the first time on the Dyno, so no comparison to previous set-up (ModernCo street header, Crane 18's, 60 MM TB and an AMM intake)
Kinsler ITB's Dyno sheets
Kinsler ITB's Dyno sheets
'02 Dodge ES, Stone White, MTX, '01 Magnum swap, ACR sways, Tokiko blues, Mopar
2GN lowering springs, Comp 200 cam, PT Cruiser clutch, bolt-ons.
'02 Plymouth ES, Stone White, ATX, free project.
'00 Chrysler LE. ATX (Fiancee's) stock. '02 engine from above car. Mopar springs, Tokiko Blues.
-
- 2011 Silver Contributor
- Posts: 4829
- Joined: Mon Jul 14, 2008 6:09 pm
- Location: Uniontown, Pennsylvania
No, it's about right for the parts involved and there's nothing wrong with it. It really needs more cam and then good head work to match the cams. The 2.4s really like more duration than a 2.0.
BoogerMan
'95 Ply NYG ACR sedan 12.31 @ 111 all motor 2.4 swap - puked
'95 Ply NYG Sport Coupe 2.4 SOHC. Yes, 2.4 single cam.
'01 ACR Stone White
www.boogerbushings.com
'95 Ply NYG ACR sedan 12.31 @ 111 all motor 2.4 swap - puked
'95 Ply NYG Sport Coupe 2.4 SOHC. Yes, 2.4 single cam.
'01 ACR Stone White
www.boogerbushings.com
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Nice flat torque curve...
That is what makes it fun.
Still what, about 30 - 35 hp more at the stock redline? And gaining. Not too bad.
That is what makes it fun.
Still what, about 30 - 35 hp more at the stock redline? And gaining. Not too bad.
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester
for comparion, Crane 28s with NOT ENOUGH of the right kind of head work and Blackdog intake. I may take a swing at some ITBs this fall with Crane 24s. I'd like to have a set of Crane with lift of the 22s and duration of the 28s. I just need the spare cash to make it happen.
BoogerMan
'95 Ply NYG ACR sedan 12.31 @ 111 all motor 2.4 swap - puked
'95 Ply NYG Sport Coupe 2.4 SOHC. Yes, 2.4 single cam.
'01 ACR Stone White
www.boogerbushings.com
'95 Ply NYG ACR sedan 12.31 @ 111 all motor 2.4 swap - puked
'95 Ply NYG Sport Coupe 2.4 SOHC. Yes, 2.4 single cam.
'01 ACR Stone White
www.boogerbushings.com
Nice numbers Tom and Jeff. Jeff I think sometimes big cams are overrated. Dont get me wrong you have to have big cams to make power I know, but after building some pretty big N/A 2.4's I've had luck both ways. It seems to me that the engine combo makes all the difference. As an example I made 256whp/196tq with Crane 22's back in the day. Granted that was a race motor w/ about 13.5:1 CR and a VERY nice head from when I was running NDRA COMP4. Big numbers can be made from smaller cams but the combo has to be spot on. Tom love the ITB's! I am making a set now for a new 2.4 I am building and when I am done I will post the results. Hoping for the 240whp+ ish range, but we will see.
Last edited by dpuck153 on Thu Mar 15, 2012 12:38 am, edited 1 time in total.
Here is a dyno chart of my current 2.4 that I made from stuff laying around the shop. Stock PT bottom end, decent head w/ stock valves(not shaved), custom Crower cams w/ .420ish lift & Crane 20ish duration, box style intake w/24lb injectors,Fast Fab LTH, blah, blah, blah. Sorry about the speed being up there instead of RPM I messed it up somehow extracting the file with Dynojets software. Car has a MP PCM so where the rpm's fall of is 7600ish.