Search found 1135 matches

by jrumann59
Fri Jun 06, 2014 2:28 pm
Forum: Engine
Topic: Strange hissing sounds in strange locations.
Replies: 6
Views: 762

Thanks for the quick response! Yes, you were right to assume that the right and left are as sitting in the driver's seat. EDIT: Scratch this Thanks for clarifying that there is no vacuum for the fuel pump, and that it could be the fuel pressure regulator or the leak detection cannister. Is there a ...
by jrumann59
Thu Jun 05, 2014 4:13 pm
Forum: Drivetrain
Topic: What can cause those leak
Replies: 11
Views: 1236

Isn't there a vent on the top that will puke out fluid if you overfill the trans? Hopefully it's not the rear main seal, but I think the clutch would be slipping if that was the case. If you over fill it will leak out the fill hole which is lower than the top of the tranny. Unless you're filling it...
by jrumann59
Thu Jun 05, 2014 4:09 pm
Forum: General 2nd Gen Discussion
Topic: Help!? Surprise in Srt4 oil pan.
Replies: 10
Views: 1043

remenants of a shitty oil filter.
by jrumann59
Thu Jun 05, 2014 3:49 pm
Forum: Naturally Aspirated
Topic: iceman issues
Replies: 13
Views: 1612

are you sure the tube is 100% inserted. Sounds like it maybe just shy of full insertion.
by jrumann59
Wed Jun 04, 2014 3:52 pm
Forum: Drivetrain
Topic: What can cause those leak
Replies: 11
Views: 1236

Donkeypuncher wrote:Isn't there a vent on the top that will puke out fluid if you overfill the trans?

Hopefully it's not the rear main seal, but I think the clutch would be slipping if that was the case.
If you over fill it will leak out the fill hole which is lower than the top of the tranny.
by jrumann59
Mon Jun 02, 2014 12:50 pm
Forum: Previous 2GN.org National Meet Discussions
Topic: 9th Annual 2GN.org National Meet/Chryslers at Carlisle 2014
Replies: 398
Views: 29423

I have been around lurking. I am mellowing as I get older, not nearly as much bravado as years past.
by jrumann59
Mon Jun 02, 2014 11:28 am
Forum: Wheels / Tires
Topic: Asian companies bring back old popular tread designs
Replies: 7
Views: 1524

IIRC Ohtsu always made Falken's budget line, I think Falken is trying to split their brand between higher end and budget.
by jrumann59
Mon Jun 02, 2014 10:23 am
Forum: Previous 2GN.org National Meet Discussions
Topic: 9th Annual 2GN.org National Meet/Chryslers at Carlisle 2014
Replies: 398
Views: 29423

registered and room reserved.
by jrumann59
Tue May 06, 2014 9:32 pm
Forum: Previous 2GN.org National Meet Discussions
Topic: 9th Annual 2GN.org National Meet/Chryslers at Carlisle 2014
Replies: 398
Views: 29423

Are we Sure HW is still good to go. I drove by there couple of weeks ago and looked pretty bad even for HW.
by jrumann59
Tue Aug 20, 2013 11:43 pm
Forum: Audio / Security / Electrical
Topic: Head unit
Replies: 5
Views: 678

what the hell is the remote wire going to?
by jrumann59
Wed Aug 14, 2013 9:52 am
Forum: Engine
Topic: Ebay exhaust
Replies: 9
Views: 914

I know i'm late on this but here's my .02... aside from thickness Stainless steel is stainless steel so the main concern should be the exhaust note. If you end up not liking it you can always change the muffler and / or add a resonator. the other thing is you need to realize that this is not a comp...
by jrumann59
Mon Aug 12, 2013 10:24 pm
Forum: Engine
Topic: Bad Fuel Pump
Replies: 2
Views: 424

sounds like a fuel pump. Whne the tank is above 1/4 tank their is enough fuel to cool the bearings when it below the bearings are seizing. Does it start back up after 15 minutes or so?
by jrumann59
Sat Aug 10, 2013 1:08 am
Forum: Vendors / Group Buys
Topic: ByVampDesign- Leds, T-shirts, Vinyl Graphics!
Replies: 5
Views: 1781

how much is the trunk LED kit?
by jrumann59
Tue Aug 06, 2013 3:17 pm
Forum: Engine
Topic: engine lag
Replies: 7
Views: 655

what spark plugs are you running?
by jrumann59
Mon Aug 05, 2013 10:00 pm
Forum: Engine
Topic: engine lag
Replies: 7
Views: 655

have you tried changing plugs and wires first. Without a wideband hard to say for sure if it is a fuel issue.
by jrumann59
Mon Aug 05, 2013 3:32 pm
Forum: Engine
Topic: Ignition parts
Replies: 9
Views: 806

maybe a small vacuum leak, it would explain the gas usage, the leak is small enough not to stall the engine but enough that the engine needs to add fuel to keep it running.
by jrumann59
Sat Aug 03, 2013 10:39 pm
Forum: Previous 2GN.org National Meet Discussions
Topic: 2013 All Chrysler Nationals/8th Annual 2GN.org National Meet
Replies: 649
Views: 38723

Good god, I just checked Carlise's page and you guys had 52 there? I may have to make a double trip to Carlisle next year. Performance and Style and the Chrysler nats...... That doesn't count most of the SRTForums dbags either. EASY THERE DICK. In his defense he said MOST not ALL. But is true SRT f...
by jrumann59
Tue Jul 30, 2013 2:55 pm
Forum: Suspension, Steering & Brakes
Topic: Anyone use brake ducts similar to these?
Replies: 23
Views: 2280

Then for your application it would work. I do not understand how your rotors are getting so hot when DD unless you are panic stopping or you have a dragging caliper. What rotors are you using?
by jrumann59
Tue Jul 30, 2013 2:23 pm
Forum: Suspension, Steering & Brakes
Topic: Anyone use brake ducts similar to these?
Replies: 23
Views: 2280

Why, Neons have always had over engineered brakes. Unless you are doing AutoX or endurance racing I see absolutely no reason to use this. On top of that it will add drag and make your car slower.
by jrumann59
Tue Jul 30, 2013 2:21 pm
Forum: Engine
Topic: Installing a header on a 2000 - *Interesting* bit of info!!
Replies: 19
Views: 2272

Crane 12s have always been mild cams. The joys of owning an ATX you lose so much through the drivetrain. Stock Neon SXT/ES ATX dyno numbers 94 hp to the wheels. Net loss of 38 HP at the wheels
by jrumann59
Mon Jul 29, 2013 10:19 pm
Forum: Engine
Topic: Installing a header on a 2000 - *Interesting* bit of info!!
Replies: 19
Views: 2272

Not to insult the OP, but Neons have always had restrictive exhausts. Not JDM restrictive but restrictive none the less. Understood, and I (mostly) agree. The 1st gen Neons actually were not that bad, 'from the factory' - Compared to other economy cars. No other cars in the Neon's class, had a 2 1/...
by jrumann59
Mon Jul 29, 2013 10:36 am
Forum: Naturally Aspirated
Topic: exhaust manifold
Replies: 4
Views: 1046

An OBX or Megan Racing Header is shorty they are slightly better than stock due to slightly bigger primaries and smoother air flow the downside they use cheap SS that will eventually rust out. TTI makes a nice mid length header you may need to massage the firewall and will need to have O2 wires exte...
by jrumann59
Mon Jul 29, 2013 10:27 am
Forum: Engine
Topic: Installing a header on a 2000 - *Interesting* bit of info!!
Replies: 19
Views: 2272

Not to insult the OP, but Neons have always had restrictive exhausts. Not JDM restrictive but restrictive none the less. Heall with all my bolt ons I made good power but when I added the Fast Fab Header and 2.5" exhaust on my 1st gen I can actually climb a hill in 5th and pick up speed.
by jrumann59
Fri Jul 26, 2013 3:06 pm
Forum: Off-Topic Media
Topic: Dodge Dart news
Replies: 811
Views: 91335

...hostess is back without the unions that bankrupted the company last year. International Baking Co. management, not the unions, bankrupted Hostess. Union workers gave concessions several times but those in management gave themselves raises when the company was virtually insolvent.[/off-topic] No ...
by jrumann59
Fri Jul 26, 2013 12:20 pm
Forum: Suspension, Steering & Brakes
Topic: how much will it cost to lower?
Replies: 14
Views: 1321

nerox wrote:
ThatKevin wrote:3. get an alignment ($80-200)
$80-200 for alignment ?!
$80 for a one time alignment, NTB offers 3 years of alignments for like 180-200. NTB deal is nice if you do a lot of work on your car or need to replace parts.
by jrumann59
Fri Jul 26, 2013 12:07 pm
Forum: Off-Topic Media
Topic: Dodge Dart news
Replies: 811
Views: 91335

The Marchionne has stated he wanted to use Chrysler to get a foothold back in the USA so instead of original designs he is going to use Chrysler as a test bed for Fiat designs that would work in the US ... Chrysler had already failed by 2007 ... Daimler paid Cerberus, the vulture capital company, t...
by jrumann59
Fri Jul 26, 2013 9:42 am
Forum: Off-Topic Media
Topic: Dodge Dart news
Replies: 811
Views: 91335

The Marchionne has stated he wanted to use Chrysler to get a foothold back in the USA so instead of original designs he is going to use Chrysler as a test bed for Fiat designs that would work in the US most consumers are dumb and will see Chrysler as an American car company and any failures FIat bri...
by jrumann59
Thu Jul 25, 2013 10:24 pm
Forum: Off-Topic Media
Topic: Dodge Dart news
Replies: 811
Views: 91335

Gov't should have let it go bankrupt... You are my friend and a gentleman but I have to ask- are you serious? While cars that get us excited are important, in the big picture, letting Chrysler post-Cerberus go bankrupt and the ripple effect that it would have had on this country's economy is a much...
by jrumann59
Thu Jul 25, 2013 4:01 pm
Forum: Suspension, Steering & Brakes
Topic: how much will it cost to lower?
Replies: 14
Views: 1321

Depends on how many times you want to do it. If your mechanically inclined than the cheap and wrong way is to get 1st gen R/T or ACR springs and replace your stock ones. Sometime in the near future you will blow your struts but it is the cheapest in the short term. If you want a true performance sus...
by jrumann59
Thu Jul 25, 2013 3:53 pm
Forum: Cars For SALE
Topic: FT: 99 plymouth dohc coupe 5 speed
Replies: 31
Views: 15619

If you are looking for consistency, put the AZ unit in there. The chiming will drive you insane. About every 10 to 15 minutes. I actually installed a temp gauge in the heater tube to verify it wasn't actually getting that hot. It would never boil, or anything that correlated with the cluster readin...

Go to advanced search