2GN.ORG

side mount replaced along with upper/lower torque struts again, vibration still here exactly as described

I'm throwing 2 codes in my 2000 atx plymouth neon that read small/large evap leak. This has been so for awhile and I just over looked it. I did not see anything noticeable under the hood so my question here. Is there a way to check the rear hoses other than leak down smoke test?

yet another neon owner here in Cary, NC!!

ya know I've been suspecting the side mount causing this problem and I've been dreading replacing it. I just did my timing/water pump 8 months ago so that's already done. What's killing me is that I just replaced that dang belt tensioner so I had that bracket off and now i gotta get it off again... ...

Yeah, after all the bolt ons and engine mods I did (cam, port/polish, rebuild bottom end and pistons) the biggest boost to my power was the FastFabs LTH (3" dump) and catless with 2.5" exhaust. It was ridiculous. I will say, that the biggest and best gains that I have gotten in a Neon, come from [p...

I did this before and did not feel comfortable driving like that. Ultimately I bought the bolt drill extract kit from advance auto and it got the job done.

So I recently felt rubbing/vibration effect coming from the front end. At first it was happening when I started to move forward from being stopped, when turning left or right, when starting to moving forward from a stop on a hill and sometimes I feel it as I'm driving at around 18-20mph. I recently ...

Update, problem happen to be #7 fuse in the inside compartment. Seems to control the compressor, rear defroster, and backup lights.

it does not come on as soon as I put it in drive, if it comes on at all. Its acting real some timey. Now even while in drive the AC only gets cold sometimes and then gradually back to warm air.

I know charge levels are fine, gota check that fan

2000 Plymouth Neon ATX, SOHC I just noticed that my AC only gets cold when the car is in drive, when in park neutral or any other gear it stays warm. Anyone have any clue of what the problem could be? I did recently blew a fuse somewhere because my reverse lights don't come on when I put the car in ...

turned out to be a wheel beating, hub assemble replaced

rattle/clanking noise coming from this wheel, on an initial inspection nothing appears to be loose,worn,or broken. The noise is constantly and can be heard as soon as the vehicle reachings 10+ mph. Any suggestion on what to inspect in further? Common problem?

2000 Plymouth Neon 'stock

don't forget to replace the timing belt tensioner; my was flexible by hand and also starting to leak oil

ok for the past few days ive noticed antifreeze spots under my car coming from passenger side where belts are. Ive noticed the spots there even when the car is not running ( id pull into a spot and immediately kill the motor) and still saw the antifreeze spots. I suspect the water pump but decided t...

I found a pair of low mileage fatory struts at the yard but on my 00 neon I seem to have the sway bushing it attached to the strut and on the 05 strut it does not have that bushing their. How would I work around this or have this work?

I cant find any info on the stock r/t springs for a 00+ neon. I just ordered a set of gr 2's and I have a set of r/t springs with low miles. Anyone know how much this is lower the car over stock springs? Any pictures of height?

will the stock 15's take a 205 size tire?

what side skirts are those

To loosen the tension on the ps belt you insert a 17mm wrench on the top of tensioner. At the bottom of that tensioner is a piece that looks like this... http://www.autopartswarehouse.com/images/product_images/thumbs200/WORLDPAC/W01331614699GAT.JPG mine is all broken and spins freely. when I install...

I was just driving home on the highway when I heard a popping sound. I got home and my power steering belt was missing. I installed a new one and it immediately disconnected. On further examing it seems the tensioner at the bottom (part that rotates clockwise is broken) I can't get this replace for ...

Anyone know the size of the couplers that come in the purchase of a new AEM intake system?

what about the drilled hole in the AEM intake, what plugs into that slot?

how can I get that rear bumper, its KA

I watch the Doctors everyday and they've always said any paid in your chest should be looked at as serious and you should consult with a doctor asap!

I just purchased a used AEM cold air intake without the water bypass. My question is, the intake has a drilled hole in it and a nippet style line. What lines plug into the aem intake?

Installed in my 2000 neon for the past 8 months has been the pioneer F500BT. This was hard wired to the pink power wire of the stock radio harness and also powered by a cigarette lighter style DC charge. http://www.pioneerelectronics.com/StaticFiles/Manuals/Navigation/AVIC-F500BT_OperationManual0714...

Danteneon, the new seats are power so they require the lifted bracket.

very interesting intel guys, thx! Steamer any pics of what you fabbed up? Looks like I'm going to go that route.

Somehow I have not ate the steering wheel yet and I only have 1 front bolt in!

I found some Chrysler Sebring 01 seats that fit into a 2nd Gen neon seat location. 1 of the lower front seat bolts line up but the arm is too short for the other to bolt in. For the rear 2 bolts, they dont even reach the factory bolt holes, so it looks like I may have to drill some holes for new bol...

that's the lame part, theirs not one.