2GN.ORG

any info on the difference's in the harness's?

what covers a tune up?? it has fresh oil new plugs new wires new filters ?? oh and its a mtx

so to make as painless as possible, would be to use a 01 pt block and ecu and harness all from the same year car as my neon?

it wont touch it , sort of takes a dump at around 140 and slowly and i mean slowly climbs to 160 any idea? i think a compression test is in order and go form there maybe? then look at the cat if that checks out?

so 160 is roughly 100mph give or take a mph , so what would starve a car of its top end?

hi, i cant realyl find an answer for this, what ECU do i use my stock 2001 sohc one or do i get the one from where i get the 2.4 na block? and i know in the first gens you can use stratus 2.4's woudl a computer from them work if the car is a differnet year?? and is the rest of the wirings liek a fir...

hi, not sure if it fits here or not, but what is the average top speed of a 2nd gen non mag???? would or should it break 160kmh ?
thanks

the numbers on my cam and box are CHR226/355-25-10 (158CHR0004 also on box ) , it is a custom grind and it a lil bigger then the 14
thanks for the help

the cam specs can be seen here

it would land somewhere between the 14 and the 007 , it was a custom grind im sure if i remember right, Isnt the 004 the old PN for the 14? I always thought the only cams with single digit PN's were custom grinds. Where does the 004 fit? 95 10 mag 200 12 400 14 007 005 008 14 fits fine in stock head...

hi, i dont have one butthe picutre i seen on here awile ago did have a sticker saying howell on it ,
you could see if it will rev higher then stock to tell , im sure soemone else with one can give you some adivce

hi, no the cam will fit in the head with out boring anything if i remember right, the 004 is basicly the crane 16 wich is a lil more agressive then the 14,,, i plan on upgradeing the springs and vavles

see im debaiting this here 1 either a MS or afx with an s-afc 2 an rt head and up graded springs and such with higher compression 3 a long tube header 4 a new intake not sure what yet and a 60mm tb 5 and my crane 004 i just dont wanna do this and end up with 150whp, i would like to be in the 14's to...

i didnt metion the header or intake cause its pretty much a given, now will an r/t head be fine? and what kinda port job on my stock head ( non mag)am i lookign at?, as far as compression i was uping that anyway if i put a cam in my car

i have a crane 004 cam. i im trying to decide if i wanna install it or sell it. i know i will need MS to run it new vavles and a cam gear , now i am pretty sure i need porting to run this cam? (non mag) and what kinda gaisn am i lookin at with this cam(just deciding if its the way i wanna go) thanks

i know it lugs but when im closing in on 3000 rpm it does liek a bucking that feels a little like a clucth slipping and i look at my boost gauge and it is bouncing from 12- 13 to 10 or 9 once i cross over 3300 rpm the bucking stops and the car takes off as always.. can i lug a turbo car? and when it...

hi, i have a question with my car(2004 srt-4) if i am in 4th doing around 40 or so (about 2000 rmp) when i put the pedel to the floor it bucks as the rmp's climb, is this because of the boost?
any help would be great thanks

i have hydro clutch

great thanks for the help!

i will be putting it in my 01 so it will be swichted over( bell housing i assume) to fit my hydro clutch

thanks, no its not for an upgrade, i put the diff pin out the bottom of mine, and am looking at what is better , i cant find a 3.94 one and i can get a 95 one alot cheaper then anything else i have found

hi, i looked the part number up on this http://www.neons.org/forumdodge/trans.htm

and went by that

whats the difference in proformace from a 1995 sohc trans . and my 2001 sohc trans both are mtx . i have the numbers but im not sure , any help would be great here are the gear ratio's 1995 sohc base 1st gear ratio 3.54 2nd 2.13 3rd 1.36 4th 1.03 5th 0.72 Final Drive 3.55 Reverse Brake NO OTGR Code ...

thats but i found the numbers off it and a chart off here so i know what it is now thanks though

how can i tell for certin if the tranny is a 3.94? i mean the first gens? is there codes or numbers on them? if so where would i check the numbers? and where would i find them on the trans?
thanks for your time

ok just to double check before i buy the 2001 pt tranny, it will bolt right up , i dont need anything else ,no mounts, no axles no hubs , every thing on my car will work?

thanks this is good i cant find a rt tranny and i ruined mine, thanks for the help.

p.s is there anywhere ican find more info on this thanks.

will any year pt trans work? if not what years did they have the 3.94??

will a pt cruiser trans out of an 01 bolt right up to my 01 lx neon? if now what mods would have to be done? thanks

i called nappa 3 different places they said they couldnt get anything for me at all,

i didnt mean i wanted it to feel like stock, i ment that i wanted it to look and act like its supose to(the motor movement i mean) , i really dont wanna leave it if its bad .i was gonna put inserts in it anyway , and my exhust is broke agianin not even 3 months and im pretty sure the motor jumpig is...

alocal junk yard here has the identical car in sliver , he is taking the mounts off for me on monday , he didnt say what he wants for them yet im sure it isnt much if there still good that is. im gonna order soem inserts to put in them , is there a baindaid ican do till i get them like hot glue or s...