2GN.ORG

check the cables see if thier loose and theres no corrotion.. if not your alternator is prolly dead and needs to be tested... if you have a voltmeter test the voltage at the battery when the car is on and post your findings the problem is if your alt is dead or its not producing enough voltage your ...

since im able to make boxes with wood or fiberglass is there a strong enough market in these forums to put up a 2gn box store sort of

keep in mind they should cost less than $200 nowadays, when i baught my set 4 years ago they were at about 255 a sub,... 4 years later they still hit like if they were new, and they still look new too... these babies will take some punishment as long as you dont overpower them and put them in a reco...

well i was asked to do this so here we go what youll need depends on what your going to use to let you know.. in this writeup im going to use an LED the fist thing you have to do is to figure out where you want your LED, usually inside the cluster is good or arround its trim. its pretty simple reall...

ok ill start one now... in the writeup section. ill do it with an LED

ok here you go:
http://forum.2gn.org/viewtopic.php?t=33269

actually the secondaries thing isnt my intentions but that would be cool, but you can do that with your existing cluster... if you want me to write a writup with the stock cluster i will

dude the ohms dont make the sub itself different, it enables you to extract more power out of your amp... you should deside how many subs you want and which amp first before you pick a sub for example if you pick a 2ohm sub and get a mono amp your never gonna get all you can out of that amp so you b...

yea t took a while to find the builder

where did you get your materials because i was thinking about doing some glasswork myself and what dose it go for also i looked at that spec sheen and i couldnt find the recomended enclosure specs, all i found was the displacements. but the specs you posted sounds like a sealed enclosure spec, did t...

lol

have you thaught about fiberglass.. it really isnt all that difficult, the hardest part really is getting the materials

that actually sounds interesting dante thanks

get the spec sheet for the sub, it dosent matter which way the sub is facing because the required volume will stay the same... with the exception of when its inside the box you have to make it a little bigger because of the subs displacement.... but at the same time your not saving that much space i...

get the alt from the 6-05+ neons, upgrade your ground lines then try it... you can always add a 2nd battery with a silonoid later (its required if you want to do it right)

the problem is that addnig another battery is also adding more stress to an alternator because now it has to charge 2 batteries.

$200 US, i can get it to you for 150 at the store which im sure will end up being more because of shipping versus if you buy it online

guys.... if you look at the lotus.... the whole guage is red and the letters are black... im looking for an overlay that will let red though what is currently white

it was a difference of 3db needs half as much wattage to produce the same SPL (IF every other spec matched between the subs in question) there are other factors that make a good sub sensitivity isnt the end all be all. but usually a sub with a high sensitivity is made for high Q but not really SPL. ...

careful with thier subs they are all DVC's and thier very picky, look for a sub that has a high sensitivity... youll get more out of it

¡

YES!!!!! you got it lol

its not unless you have your toggle switch on all the time, or your using the zex WOT switch along with

yes thats what im saying.. the harlan window only has 2 setable points the lowest being 100rpm, so if you set it at 100 and the off at 3200 then what about when you reash 4900? its not going to open again unless you have an rpm switch along with the harlan window. thats why im telling you to rig it ...

right the harlan is active at 3200-4900... which means the secondaries are open betweet 3200-4900.... which is the opposite of the actual R/T timing the reason why youll need the window and the rpm is the window will have to be set at 100-3200rpm... well then what about the 4900 point see what im sa...

no RCA's, theres an Accessory line along with a +12v and a ground. the inputs are taken from a harness at the back of the radio or are taken from the speaker lines somewhere. NO factory radio comes with RCA's in the neons... and the only one ive seen that dose is the Scion upgraded pioneer radio tha...

under the electrical porting i have a project posted...

im posting here because has anyone done or know where i can get a cluster face that lets red light shine though like this lotus

http://www.lotuscars.com/type72d.html

this is the car that inspired me, the guage im changing to the same style which is very easy
http://www.lotuscars.com/type72d.html

correct

im thinking of doing some minor fiberglass work heres my idea im gonna move the key cylender to the center console next to the driver like the saabs and i was going to put a push button starter to the left of the center console bezel, all of this will be fiberglass molded in that way it looks factor...

to make the default close on the secondaries your gonna need the harlan window switch and an rpm switch the problem is the window switchs have one defined on point and one off point.... well the butterflies open twice. because of that if i remember thats where having the msd is and advantage because...

correct, you might want to cover the prong. the advantage to wiring it this way is that if the window switch faults the default is to always have the butterflies open.


basically instead of using the MSD to open the butterflies your using it to close them