2GN.ORG

racer12306 wrote:Send him an email and he can make them. No group buy needed.

I've sent him a couple emails and he's yet to reply

Sending money for 2 Frank!

now a response to my question?! :D I am still at a loss. You only quoted the post, but did not ask anything. Oh FML now I see what you're talking about. Ok I basically said I'm running a 01 PT ecu. Also on that thread I'm pretty sure they said you modify the 1gn throttle shaft to fit it in the jeep...

Lol well I didnt try to modify it I'm "Travelling" and on my iPhone now a response to my question?!

Yup buy new seals from a dealer. Also my trunk had a removable plug in the bottom underneath all the carpet to drain the water. It is as if dodge knew that this would be a problem. Goodluck and yes black rtv works too.

Your '02 PCM will not drive the '95 to '00 IAC motor. You will have no idle control, plus a CEL. There is no way the 1gn IAC will work. It is a stepper motor, and the '01 and up is a pulse width modulated solenoid. You will need to remote mount the 2gn IAC valve. Fact of life. Plus the holes in the...

The IAC is not wired, or driven the same. A 1gn IAC will not work on '01 and up. Do you know what year the Jeep TB is? There are a few changes after 1996, IIRC. I know my '99 TPS has the same plug as the neon. If it is '97 and newer, you should be good there. I was reading on 1gn you swap the tip f...

The Jeep TB is mainly a 1gn mod. The IAC will not bolt on, unless it is a 2000. Not 100% sure, but the Jeep TPS might work as is. You will also need to make an adapter plate/flange, just like doing the Mustang TB. The Mustang TB in all, is the easier route for a 2gn. I can sell you a remote mount p...

Hey, thought I'd post a pic of my boost gauge pod install! Thanks for the how-to!

Hey guys, so I picked myself up a Jeep throttle body from DODGETHIS. I am currently gearing up a 60mm throttle body for my swap project. I was reading on 1gn.org that you need to also use the DOHC throttle body so I ordered one of those from DODGETHIS as well. However, on 1gn it talked about sensors...

Is there metal under the holes that can be drilled and tapped, so the proper fasteners could be used? If the head isn't bolted to the engine yet, now would be the time to do it if possible. Much less risk of metal shavings getting where they don't belong. I'll have to take a look tonight when I get...

I have a non NGC cover, but it is a non-turbo cover. Trying to think of any non-NGC turbos that weren't from Mexico :-k Goodluck cause the stratus RT was the only one lol. And ya I have a non-turbo one but my car is not going to be "Non-turbo". :D http://en.m.wikipedia.org/wiki/Chrysler_Neon_engine...

True but out of the 2 holes down the middle one does not line up with a hole. Hrmm know of any pre ngc 2.4 turbo that I could snag a valve cover off of?


Stratus RT is what I can think of but that'd probably be hard to find. Car-part.com here I come

So just wondering if anyone has a suggestion for me. I am using a pre-ngc head but wanted to use the 2.4L Turbo valve cover. After setting it on the head, some of the bolt holes are in the wrong spot. All the ones on the perimeter are fine, its the ones that go down the middle by the spark plug tube...

Feedback For: DODGETHIS You in the transaction(seller or buyer): buyer Feedback Rating: +1 Comments on the transaction: This guy SUCKS! Just kidding! -Dealmaker, great communication, fast shipper, awesome packaging! Item received promptly and in excellent condition! Thanks for the throttle body man!...

jonnymopar wrote:5000+rpm on a daily basis

LMAO, made my night. Balls to the walls!

The pitting would be fine if it's not where the gasket seals. It looks like most of the damage has occured where there is no seal. (Which is why it's pitting in the first place.) The small pit between the two oil returns looks like it might cause the most problems. You'd need to hold the gasket up ...

What did you clean that with?

As for the pitting cannot really tell how deep it is in pictures. IMO it would never hurt to get it planed down. Although most of the pitting seems to be taking place Far enough from the ports. However better safe than sorry get it machined!

This. You would prolly see some increase just installing them straight up, but degreeing them with the use of a dyno will get the full potential for your specific set up. You could play with it yourself, and use the butt dyno. Worst that can happen is you put them back to zero. Edit: Pistons have a...

Great write-up. I sent you a PM with some questions man. Should have posted it on here for everyone else to see. Feel free to post my message I sent you on this thread.

Hey guys, so got it all figured out, stupid me. However, I picked up a set of 2.0 DOHC cams. I am getting a set of adjustable cam gears soon too since I was told and read somewhere that to benefit the use of 2.0 cams was to advance and retard each of the cams. I Now to my question since I could not ...

Yep, and I even made a how-to on here if you are interested. It was my first time working with CF and it came out great. Sorry, don't mean to hijack your thread. Just thought you might be interested. http://img.photobucket.com/albums/v697/sidepipe87/IMG_0621.jpg http://img.photobucket.com/albums/v6...

occasional demons wrote:

Now your car feels like it's been to the doctor: They checked everything else, before they found the problem.

Now just make sure if you put your turbo back on you have a spare ignition

lol its all good man. im now thinking i have two problems.... 1) the said brown wire has to be shorted, broken, or otherwise f****d 2) either the ignition wire or the PCM ground has to be bad as well... ill start more trouble shooting when i get home so i can get a better meter than the one ive got...

Hopefully the fixes it. Keep us posted. And sorry it was late when I replied I mis-read what you wrote. Well not mis-read mis interpreted.

I know eh!

Bump this to the top. Did these get made? These look awesome and would be great to have a bunch to give out at meets and such ( sticker size of course). I wouldn't mind a big one either.

^ lmao that comment made my morning.

Ok we I just wasn't sure as to how long it takes to do the mock ups and it ends march 7th. No worries.

Can someone start a group buy for these... maybe get Jason to. I want one!