2GN.ORG

Yea this switch only has 4,6,8 cyl options. Going to talk to electrician/mechanic at my job and see if he can come up with a answer. If not I will take it to the audio place that said he would put it in for me The relay 86 and 30 should b powered from the battery correct? And I dont have a fuse wire...

Now got code p0352. and driving with the wires switched, the car would buck between 2 and 3k. So switched wires back. And have the switch reading the rpms soul messed up again.dont kno what the prob is. Going to try to run a dif ground wire to the coil and see if that helps

Help me!!

U should b able to use any auto from 00-05. I believe theyre the same

It is u can clearly hear the butterflies opening and closing. glad I finally took the time to get it wired up

Could b a lose wire/bad ground. for the speedo check the speed sensor

Problems solved.. Wired the switch/fuel pump, relay connection better, check engine light hasn't come back on so far, crossing my fingers. And the rpm thing, I noticed that the coil pack electrical harness wires went, starting closest wire to the front of the car, blue/pink, green/orange, black. Fro...

I had a srt on my car for a while. its to the point where you have to yell to talk to ur passenger while cruising on the highway.. I'm on my second magnaflow muffler. I like them. Not too loud, prety deep sound. I only have a single exhaust outlet though. Dont do the srt dude unless u don't mind get...

And I wired the switch (12v supply) to the blue/white wire from the fuel pump relay, which I saw on another persons thread. I think that may be the reason I'm running lean. So I'm going to switch that to a diff 12v source and see what happens. Still dont kno y the switch isn't reading the rpms right...

I used mine from the old one. But I've had the mag im installed for months now, since I did my head swap. So I must have disconnected something. How can I find out if a relay is bad?

Went to advanced auto had it scanned only code that came up was p0171 bank 1 running lean. Not sure as to how this is connected with the secondaries but check engine light want on before I wired the rpm switch. And my ac isn't blowing cold now either wtf!

Ok so... I hooked it all up. Everything worked, I set the rpm window low enough so I could here the butterflies open and close and they work! But my problem now is that the switch is reading the rpms crazy, at idle it will go from 8000 to 3000, them end up staying a around 3000-3500. Y would it be d...

Congrats! Def a lil...... Ok a lot jealous of ur new car!

Ur car do as u pls... fuck peoples opinions they shouldn't matter as long as u like it

Just remember next time to not throw urself under the bus with a topic like this..

Ohh ok. Got it. Thanks for the help. sorry I'm not good with the electrical stuff haha

Just confused bc if blue wire from switch goes to 85, the other side has to b grounded, but in ur text it says power to 86 and 30. Maybe in just not understanding, but I think I have it figured out. Haven't had time to work on it yet bc of crazy work hours

Doesn't the relay have to be grounded??

Awesome thank u. That confirmed my new diagram I made up after reading up more online about relays. Ill have to try it this wkend°c work is crazy busy and have no time to do it

No it does.. I guess im just asking how I tie the relay into the mix

Does the mtv actuator draw more than 3 amps??

Trying to hook up the secondaries on my mag im... I kno theres a bunch of how to s but they r for the harlan and msd. I tried switching stuff around to get out to work but failed. Someone help me out and explain which wires go where our draw up a diagram pls! This is the one I have and a relay http:...

Welcome to the site!

^ this place def doesn't kno what they r talking about!

Yea its most likely "blow by". Oil blown through the pcv valve. Take the manifold off, clean it out replace the pcv and get a catch can.. Hopefully that'll solve it!

Drop looks awesome man! Not too low not too high. Hows the ride??

And u running straight pipe?

Decisions.. decisions..

Welcome!

Would a spiralflow do anything to quiet a srt rear section on a n/a?

Yup

Yes people pls post lots of pics for those of us who couldn't make it out there!!

Can some one make my car px8 black and glossy black wheels with no chrome lip and drop it like 2 inches? That would be awesome! Thanks



[/u]

Thats awesome!