2GN.ORG

Yeah a muffler is a must have

03blackrt wrote:I find the stock r/t exhaust is nice with my lth. It's relatively quiet when I'm not on the go pedal. IMO

Yeah but its too restrictive for a 2.5 pipe with a nitrous build though.

Threadjack :rofl: Sorry. So I want to start off just with fuel and use the stock PCM to control spark. Worry. Can I use the MS to control rev limit without a MSD right now? Won't go spark until my magnum head and cam are installed. Just want to run and tune before the change so I know if something g...

Okay when I get my LT header installed I preferably want to get a single exit exhaust right out my drivers side rear. I already have a cut out for my current exhaust, it makes sense and with all the crowd going with dual exhausts it is different. Problem. Noise and my local police officers. Folks ar...

BTW are you using Alpha N or Speed Density?

thanks! Just wondering cuz it'll be in primer for a month or so

OMG someone has MSQ stock? :wav: Reason I say that is because I was going to go with a SAFC to tune my all motor setup, Ported and polished magnum everything, 60mm TB, crane #14 and Fast Fab LT v2 header, fuel only. But now I'm thinking of going with the MSQ, just to get rid of the RPM limiter. A ba...

actually the magnum IM is very close to the V-tec, both just allow more air in at a certain RPM at WOT WELL... I gues sif you want to say apples are like oranges because they are both fruit, but vtec REALLY is different in the sense that it has more to do with cam and valve timing and what not as o...

do not do 18's they look like wagon wheels and look like ass. For a show car go 17 or less. In my taste go for 6 spoke or 5 spoke wheels.

36 read the thread and don't bother to poll :banghead: I'm still leaning towards barbed wire though cuz of this. http://memimage.cardomain.net/member_images/1/web/601000-601999/601795_29_full.jpg http://www.forwardmotioninc.com/html/linked_photos/cox_srt4/mopar_side1.jpg http://www.stripeman.com/Mer...

Zex FTL

http://youtube.com/watch?v=VYf5OIQG8XA

just remember to go easy and take your time. It is a bit frusterating to get the lense out but remember to just heat/pry, heat/pry, it'll eventually give.

My car is going to be painted two tone this winter. Gloss on top and stock PG8 Emerald Pearl Green on the bottom. I have a few ideas but would like your opinions on them. First pick is my color scheme that I've had in mind for the last 5 years and have pretty much stuck with it. I already have the R...

usually you can count on the more expensive ones to be the best bang!!

Nice, I didn't even know they had a USB adapter that would work. Stuff gets better all the time. Can't wait til my engine is done

If they are stock headlights they wont come apart right in the oven. If they are depos or other aftermarket headlights then you can turn the over to 200, turn the oven off, put them in for 5 minutes, pry some and repeat the process. This way theres no way to crack/ruin the stock lenses. Stock headl...

what kind of rustoluim... there are several types? i think they make metalic... which would look professional on a car... but what type should i use? hows it holp up on the plastic? i just primered my car... i was just going to drive it like it is... but if i can do this... i'd be set tip: it takes...

http://memimage.cardomain.net/member_images/5/web/725000-725999/725378_46_full.jpg http://memimage.cardomain.net/member_images/5/web/725000-725999/725378_47_full.jpg http://memimage.cardomain.net/member_images/5/web/725000-725999/725378_68_full.jpg http://memimage.cardomain.net/member_images/5/web/...

http://www.autozone.com/R,APP292083/vehicleId,2565201/initialAction,partProductDetail/store,5582/partType,00158/shopping/partProductDetail.htm Just know that the vehicle ID is for a 2000 Neon 2.0. I'm pretty sure they are all the same, but change the vehicle to your specific year to be sure. I didn...

Don't try to open them with the oven. It will kill the headlight. I opened my headlights with a dremel. :ban: I put mine in the oven, I don't remember the temperature, for about 5-10 minutes. Get a butter knife, you'll need it to help you along. Start pulling and using the knife to pry the clear le...

http://www.popularhotrodding.com/hotnews/0608phr_03_z+chip_foose+challenger.jpg Kinda playing around with this for a pin too http://us.st11.yimg.com/us.st.yimg.com/I/vinylgraphics4less_1963_15827699 OR the bottom one that's silver???? http://us.st11.yimg.com/us.st.yimg.com/I/vinylgraphics4less_1963...

Sorry didn't get the pic. So your saying just keep the solid stripe?

Could someone please shop some cuda stripes running the length of the pinstripe in my two tone look. Silver color to match my wheels would be nice. Maybe make the stripe only one inch? http://i10.photobucket.com/albums/a104/skipsneon/calander007.jpg http://memimage.cardomain.net/member_images/5/web/...

actually the magnum IM is very close to the V-tec, both just allow more air in at a certain RPM at WOT

Worked on my large dent but not on my smaller ones. Try it. If it doesn't work then do like I"m going to do and use dry ice.

Just did this last night and it didn't work on the small dents. Went to the big dent and it popped right out!!! Awesome!!!! With the small dents I've been searching the web and found that dry ice is the way to go with the dents that don't come out. WARNING!!! Use gloves or something to protect you f...

That Looks AWESOME! I'm clearing out space in my garage today! Time to paint up the new project/beater and I sure as hell don't want to spend more than $100 or so to so it, this is perfect! Two questions first (and forgive if these have been posted somewhere before but I'm here now and it's on topi...

I know Myztykal has done this job. Mztykal where are you?

Where can you get a can of that airduster/CO2? Will the spray that you use on the keyboard work?