According to the bag I have in my room, yeppers
SRT boost gauge install, removed from part number topic
- Canada
- Junior Admin
- Posts: 4816
- Joined: Tue Jun 28, 2005 4:05 pm
- Location: Island Grove, Ontario, Canada
SRT boost gauge install, removed from part number topic
*******NOTE continued from a part number request post
******
According to the bag I have in my room, yeppers
According to the bag I have in my room, yeppers
- kc2005ptgt
- Former Moderator
- Posts: 6587
- Joined: Wed Dec 14, 2005 7:39 pm
- Location: Kansas City, MO
- Contact:
You take the upper dash off. Separate the 2 parts. Then you will see the holes for the to screws. Line it up and make the cut to fit.
O and here is Daaboots how-to
http://www.cardomain.com/ride/2092484/4
O and here is Daaboots how-to
http://www.cardomain.com/ride/2092484/4
-
racer12306
- Junior Admin
- Posts: 16015
- Joined: Sun Oct 24, 2004 8:53 pm
- Location: Baltimore, MD
- Contact:
sorry for the resurrection but,
does that part number come with the screws and such or do they have a separate part number or is there a simple way to get the mounting accesories?
does that part number come with the screws and such or do they have a separate part number or is there a simple way to get the mounting accesories?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
- jonnymopar
- Junior Admin
- Posts: 3039
- Joined: Sat Nov 19, 2005 7:49 pm
- Location: Southeastern MA
Not if you have an 00-02 or early 03. Those holes were only there on the Neon while the SRT-4 was in production. I got bit in the ass on that one.SlvrACR wrote:You take the upper dash off. Separate the 2 parts. Then you will see the holes for the to screws. Line it up and make the cut to fit.
Jon J.
2003 Neon SXT - new home, new owner. Thanks for everything, old friend.
1989 Daytona ES - 2.4L/A555 swapped
Official "I'm Going To Drive My Neon Until Jerry Buys It" Club Member #11
-
gilly02le
- 2GN Member
- Posts: 1423
- Joined: Fri Oct 27, 2006 12:13 am
- Location: Kingston, Ontario, Canada
- Contact:
got one in my 02.. it didn't have the spot to mount it (only 03+ do), so i cut the mount portion of the pod off. And Then cut a c shaped hole so that the back edge of the gauge would fit through the dash, and then epoxy'd it in place.. kinda sucks cutting a brand new piece, but you can't even tell what I've done from looking at it, so.
New Sig Time.
-
racer12306
- Junior Admin
- Posts: 16015
- Joined: Sun Oct 24, 2004 8:53 pm
- Location: Baltimore, MD
- Contact:
what hardware are people using on 03+ cars?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
- half_twisted
- 2GN Member
- Posts: 729
- Joined: Thu Jul 21, 2005 11:31 pm
- Location: Anaheim Ca.
- Contact:
what he said..jonnymopar wrote:Not if you have an 00-02 or early 03. Those holes were only there on the Neon while the SRT-4 was in production. I got bit in the ass on that one.
I got one in mine and to my surprize i had to fabricate a mounting plate for it.. its going to be a long project and alot of trips to home depot..



