i get really anxious having the part, and having to wait to get it installed.... this sucks!
Zzap UDP
Zzap UDP
i bought one from Gary, this was through ebay, so shipping was very fast... but i didn't get the instructions or recomended belt sizes. i pm'd gary, but no response.... anybody know what belts i need?
i get really anxious having the part, and having to wait to get it installed.... this sucks!
i get really anxious having the part, and having to wait to get it installed.... this sucks!
Sam-I-Am
Official "I'm Going to Drive My Neon till it Dies" Club #000046
Diablo0 wrote: "eh... your opinion doesn't matter... I'm doing what I want..."
-
p8ntballah413
- 2GN Member
- Posts: 253
- Joined: Fri Jul 22, 2005 2:46 am
- Location: Western MASS
- Contact:
-
DJ CptnCrnch
- 2GN Member
- Posts: 702
- Joined: Fri Jul 08, 2005 12:56 pm
- Location: Lakewood, OH
- Contact:
how much did u pay for it
-Matt-
04 Black SXT
AEM intake, MPx underdrive pulley, MPx throttle body, Prothane Motor Mounts , Mopar short throw shifter Eibach lowing springs, Mag Intake Manifold, Mopar 3D Taillights, Mag head, Comp 400 cam, FF LTH. All this work and I'm still slow...time to find another car
BB PIN: 317CEE50
04 Black SXT
AEM intake, MPx underdrive pulley, MPx throttle body, Prothane Motor Mounts , Mopar short throw shifter Eibach lowing springs, Mag Intake Manifold, Mopar 3D Taillights, Mag head, Comp 400 cam, FF LTH. All this work and I'm still slow...time to find another car
BB PIN: 317CEE50
ya not sure if ill order from howell again... i ordered the street prothane inserts and got the race ones... receipt said street, too! Emailed and PMed, never got anything back. ended up selling them.
NoDestiny: 2004 SXT Silver MTx: CAI, Mag Intake, Mag header, Custom made mufflers, Grounding kit, Mopar STS, boogers, Eibach springs, Rear SRT4 struts, 29mm + 24mm hotchkis sways, MPx UPD, Street Prothane MM, P-werks rear strut tower bar, Lots of fun goodies inside, see WWW
-
SilverSRT05
- 2GN Member
- Posts: 339
- Joined: Tue Aug 23, 2005 12:28 am
- Location: Sugar Land, Texas
-
DJ CptnCrnch
- 2GN Member
- Posts: 702
- Joined: Fri Jul 08, 2005 12:56 pm
- Location: Lakewood, OH
- Contact:
hmm i got mine from MP, so they came with belts...i think i payed like $100 with shiping...and i got the belts too...i never ordered from howell...i get all my stuff from Mondernperformance, there always super fast on shipping and they have everything i need
-Matt-
04 Black SXT
AEM intake, MPx underdrive pulley, MPx throttle body, Prothane Motor Mounts , Mopar short throw shifter Eibach lowing springs, Mag Intake Manifold, Mopar 3D Taillights, Mag head, Comp 400 cam, FF LTH. All this work and I'm still slow...time to find another car
BB PIN: 317CEE50
04 Black SXT
AEM intake, MPx underdrive pulley, MPx throttle body, Prothane Motor Mounts , Mopar short throw shifter Eibach lowing springs, Mag Intake Manifold, Mopar 3D Taillights, Mag head, Comp 400 cam, FF LTH. All this work and I'm still slow...time to find another car
BB PIN: 317CEE50
-
tamadrumr88
- 2GN Member
- Posts: 2318
- Joined: Thu Nov 18, 2004 10:50 pm
- Location: lehigh valley pa
-
SilverSRT05
- 2GN Member
- Posts: 339
- Joined: Tue Aug 23, 2005 12:28 am
- Location: Sugar Land, Texas
about 2 hours if you have never done an UDP before. It will go a little quicker if you put the UDP in the oven before you start because the the time at which the instructions say to levae it in is no where near long enough.
Im on AIM if you need any help.
Post up when you finish.
Im on AIM if you need any help.
Post up when you finish.
Suspension and Steering Technician at Allen Samuels Dodge in Katy, Texas
