Need help.. 2" SXT muffler pipe ID or OD?
-
- n00b
- Posts: 6
- Joined: Mon Aug 19, 2019 7:04 pm
Need help.. 2" SXT muffler pipe ID or OD?
is the pipe diameter ID or OD?
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Re: Need help.. 2" SXT muffler pipe ID or OD?
Pretty sure it is O.D. The actual muffler inlet pipe would be I.D to fit over the tail pipe.
A factory SXT muffler is 1.875 ID on the outlet. At least mine was.
A factory SXT muffler is 1.875 ID on the outlet. At least mine was.
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester
-
- n00b
- Posts: 6
- Joined: Mon Aug 19, 2019 7:04 pm
Re: Need help.. 2" SXT muffler pipe ID or OD?
So if I cut the pipe at the driver side hanger just before the muffler box it should be 1.875 ID?
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Re: Need help.. 2" SXT muffler pipe ID or OD?
I would just remove the muffler and measure it to be sure on the ID. Soak it down with penetrating oil and loosen the bolt. If it is all factory stuff, and the clamp is not rotted to oblivion, the muffler will come loose of the pipe, if you keep pushing up and down on the exit end of the muffler to rotate the inlet side on the over axle pipe. Mine was rusted to the point that the clamp bolt snapped, and there wasn't much left of the clamp. But it separated with a bit of elbow grease. I had it loose in about 5 minutes or less of twisting.
This was with well over 100,000 miles.
That measurement was the outlet pipe, so I really can't say what the ID of the inlet side of the pipe is. I would slip something over the pipe vs sliding something inside of it.
This was with well over 100,000 miles.
That measurement was the outlet pipe, so I really can't say what the ID of the inlet side of the pipe is. I would slip something over the pipe vs sliding something inside of it.
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester
-
- n00b
- Posts: 6
- Joined: Mon Aug 19, 2019 7:04 pm
Re: Need help.. 2" SXT muffler pipe ID or OD?
occasional demons wrote: ↑Wed Aug 21, 2019 9:59 pmI would just remove the muffler and measure it to be sure on the ID. Soak it down with penetrating oil and loosen the bolt. If it is all factory stuff, and the clamp is not rotted to oblivion, the muffler will come loose of the pipe, if you keep pushing up and down on the exit end of the muffler to rotate the inlet side on the over axle pipe. Mine was rusted to the point that the clamp bolt snapped, and there wasn't much left of the clamp. But it separated with a bit of elbow grease. I had it loose in about 5 minutes or less of twisting.
This was with well over 100,000 miles.
That measurement was the outlet pipe, so I really can't say what the ID of the inlet side of the pipe is. I would slip something over the pipe vs sliding something inside of it.
Thanks brotha! It's on there!