Noob OBX LTH question
- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
Noob OBX LTH question
I received the obx lth earlier and.....I for the life of me cannot figure out how to mount the smaller pipe with the flange and gasket material doughnut that it comes with.
I dont even know which end goes into the main header. After raggin on me, can someone help me out.
NorCal Homeboy


-
Donkeypuncher
- 2GN Member
- Posts: 2183
- Joined: Wed Mar 12, 2008 6:14 am
- Location: Dallas, Tx
The donut gasket goes between the end of the header and the collector pipe that bolts up to the end of the header. There will be a slight gap when the gasket is in place between them.
Both pieces have a flange on the end with 3 holes where the bolts go through to tighten them together. Should be pretty obvious where they connect.
Both pieces have a flange on the end with 3 holes where the bolts go through to tighten them together. Should be pretty obvious where they connect.
- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
-
Donkeypuncher
- 2GN Member
- Posts: 2183
- Joined: Wed Mar 12, 2008 6:14 am
- Location: Dallas, Tx
- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
Well in my defense(
) there were a few contributing factors.
1st:beer
It was after "Miller Time" when I received my parts and I was checking them out in my room.
2nd: I hadnt started working on my car yet. If I had the main header installed I would have been able to tell the angle of the downpipe.
3rd: The reverse end of the downpipe, when looking at it in my room, fit perfectly in the header.
Ok, enuff bullshit, I'll admit it... I'm a Noob.
1st:beer
It was after "Miller Time" when I received my parts and I was checking them out in my room.
2nd: I hadnt started working on my car yet. If I had the main header installed I would have been able to tell the angle of the downpipe.
3rd: The reverse end of the downpipe, when looking at it in my room, fit perfectly in the header.
Ok, enuff bullshit, I'll admit it... I'm a Noob.
NorCal Homeboy


-
Donkeypuncher
- 2GN Member
- Posts: 2183
- Joined: Wed Mar 12, 2008 6:14 am
- Location: Dallas, Tx
- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
Thanx Homie!! Remember, you owe me a rematch! I raced you( and lost2003se559 wrote:afrter all the header is in sounds fukin sik droop kant wait to smoke you lmao... seems like it made a biggg as diference and da neon is getin der slowly but surely..
NorCal Homeboy


- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
-
heydockyle
- 2011 Silver Contributor
- Posts: 4829
- Joined: Mon Jul 14, 2008 6:09 pm
- Location: Uniontown, Pennsylvania
- DroopDaddy408
- 2GN Member
- Posts: 609
- Joined: Wed Feb 11, 2009 2:53 pm
- Location: Tulare,Ca
