Questions about boost, no issues currently.
Questions about boost, no issues currently.
What is the stock boost spike (the highest psi) that a stock '05 will hit, cause I'm only getting 5psi
SHould I go through and tighten up all the connections and bolts?
sorry I'm a
SHould I go through and tighten up all the connections and bolts?
sorry I'm a
Last edited by catalyst on Sun Aug 26, 2018 12:32 pm, edited 5 times in total.
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
In your SXT without a turbo kit? You shouldn't hit any PSI.
So many neons so little time.
https://www.youtube.com/user/invujerry/videos
www.instagram.com/invujerry
Oh damn. Hmm. You can buy a boost leak kit, makes smoke come from where the leaks are. You could also check the common places, at the throttle body, where it connects to the intercooler (both sides), and where the boost pipe connects to the turbo. Remember SRTforums can help too!
So many neons so little time.
https://www.youtube.com/user/invujerry/videos
www.instagram.com/invujerry
I just went through quickly with no tools and found a connection was completely off the hose that runs from air box to the turbo, I reconnected it and I'm gonna go buy some zip ties and other fun things.
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
Ok, boost is still not proper. Just talked to guy at dodge I still have warranty, but they would have to do a $90 diagnostic to see if it is covered buy waranty and that if the boost leak was caused by a loose connection and not from any part malfunction, it would not be covered. Tomorrow I'll have to get in there and look around at all the connections. I was wondering does any one have a link to a diagram of what I'll be looking at/for?
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
there is no boost from the air box to the turbo. that clamp should never come off, since it's not pressurized. take the intake back off, and look at the turbo inlet fins, check for cracks, chips, gunk and shaft play (put your finger on the little shaft in the middle and try to gently move it side to side. there shouldn't be much, if any, play. this should have been done before purchase) since you were probably pulling unfiltered air. the car probably had an aftermarket intake (among other things, since mods are like lays, you can never have just one) before the owner took it back to stock to sell.
go to www.srtforums.com and check the how-to section for a home made boost leak check tool. should be able to make one for less than $20 from parts found at your local home depot (go tony stewart!), lowes (fuck a jimmy johnson, hope he gets hit in the head with a 2x4 from home depot [quoted from my bro-in-law from the daytona 500 in '06 lol]), or almost any hardware store. that being said, on to the list:
the connections you need to check are:
turbo outlet to intercooler hot-side pipe (hard to get to, i believe)
hot-side pipe to intercooler (under the car, left side of the intercooler when looking at the car from the front)
intercooler to cold side pipe (right side of intercooler when looking at the car from the front, easy to get to with stock air-box out of car, also accessable from underneath)
cold side pipe to throttle body (also easy to access with stock air-box out of the car)
those 4 spots are going to have 2 crappy worm-gear clamps to check for each connection. i'd suggest replacing them with t-bolt clamps, they don't loosen up as easily. also check all of the rubber hoses (hot side coupler and cold side "pipe", turbo outlet coupler) for rips, tears and holes. i'd be willing to bet one of those has either a huge rip or the band clamp is not even snug, since 10psi is a freakin huge boost leak from a vac line.
there are also various vacuum lines that need to be checked. the vac solinoid is on top of the stock air box and has 6 or more plastic lines coming off of it. zip tie all of those lines. trace them to where they go and zip tie there too.
you should also take a look at the waste gate actuater (mounted to the turbo housing with a metal actuater arm going under a heat shield to the exhaust manifold) to be sure it's not a stage 2 (adjustable for boost control) or an aftermarket (also adjustable), and if it is, make sure it's not adjusted too tight, keeping the waste gate open and dumping boost (i think that's right, tight, might be loose that limits boost. either way, if the car was sold to you as "stock", it should not be adjustable).
i'm sure there are some vac lines i'm forgetting, someone else will chime in, i'm sure, if i did. definitely don't take it to the dealer until you've checked all of these areas, as they won't be covered by warranty unless one of the rubber hoses/couplers is torn in a manner that makes it obvious it was from boost blowing it out, and not just being cut by a tool or something.
now, with all of this having been said (and hopefully done by you soon), put a catch can on that bitch! lol.
Congrats on the pocket rocket, enjoy, dude. oh yeah, can ya edit yer sig with what color you got, and lets see some pics!!!!!
go to www.srtforums.com and check the how-to section for a home made boost leak check tool. should be able to make one for less than $20 from parts found at your local home depot (go tony stewart!), lowes (fuck a jimmy johnson, hope he gets hit in the head with a 2x4 from home depot [quoted from my bro-in-law from the daytona 500 in '06 lol]), or almost any hardware store. that being said, on to the list:
the connections you need to check are:
turbo outlet to intercooler hot-side pipe (hard to get to, i believe)
hot-side pipe to intercooler (under the car, left side of the intercooler when looking at the car from the front)
intercooler to cold side pipe (right side of intercooler when looking at the car from the front, easy to get to with stock air-box out of car, also accessable from underneath)
cold side pipe to throttle body (also easy to access with stock air-box out of the car)
those 4 spots are going to have 2 crappy worm-gear clamps to check for each connection. i'd suggest replacing them with t-bolt clamps, they don't loosen up as easily. also check all of the rubber hoses (hot side coupler and cold side "pipe", turbo outlet coupler) for rips, tears and holes. i'd be willing to bet one of those has either a huge rip or the band clamp is not even snug, since 10psi is a freakin huge boost leak from a vac line.
there are also various vacuum lines that need to be checked. the vac solinoid is on top of the stock air box and has 6 or more plastic lines coming off of it. zip tie all of those lines. trace them to where they go and zip tie there too.
you should also take a look at the waste gate actuater (mounted to the turbo housing with a metal actuater arm going under a heat shield to the exhaust manifold) to be sure it's not a stage 2 (adjustable for boost control) or an aftermarket (also adjustable), and if it is, make sure it's not adjusted too tight, keeping the waste gate open and dumping boost (i think that's right, tight, might be loose that limits boost. either way, if the car was sold to you as "stock", it should not be adjustable).
i'm sure there are some vac lines i'm forgetting, someone else will chime in, i'm sure, if i did. definitely don't take it to the dealer until you've checked all of these areas, as they won't be covered by warranty unless one of the rubber hoses/couplers is torn in a manner that makes it obvious it was from boost blowing it out, and not just being cut by a tool or something.
now, with all of this having been said (and hopefully done by you soon), put a catch can on that bitch! lol.
Congrats on the pocket rocket, enjoy, dude. oh yeah, can ya edit yer sig with what color you got, and lets see some pics!!!!!
to be honest, i don't know if you should or not. i personally would not drive mine in that condition because i don't know if the motor would pull fuel during WOT based on the map reading, or if it just dumps fuel that won't have enough air to mix with into the motor. i would assume it would pull the fuel, but not being certian, i'd be parking mine till i figured it out.
i'm willing to bet you'll be back on here tomorrow saying you found a pipe going to or coming off of the intercooler that was torn or the band clamp wasn't tight at all. those 2 areas are notorious for failing on these cars. i've had my hot side coupler come off of the intercooler completely during a WOT run, and that was after having tightened all connections maybe 4 days prior.
if all of the connections are the stock worm gear clamps, i'd suggest changing to t-bolt clamps, or at least checking the stockers once a week if you get into higher boost alot or every two weeks if you drive normal with a few WOT runs every once in a while. they really suck ass. i've never had to not tighten at least a couple when i check them every other weekend.
Edit: Catch can and a check valve are great "mods", even if you want to keep the car stock for a while. take off the PCV valve and blow thru it both ways.... you'll see why. i don't think blowing 12-14 PSI into your valve cover is a good thing.
i'm willing to bet you'll be back on here tomorrow saying you found a pipe going to or coming off of the intercooler that was torn or the band clamp wasn't tight at all. those 2 areas are notorious for failing on these cars. i've had my hot side coupler come off of the intercooler completely during a WOT run, and that was after having tightened all connections maybe 4 days prior.
if all of the connections are the stock worm gear clamps, i'd suggest changing to t-bolt clamps, or at least checking the stockers once a week if you get into higher boost alot or every two weeks if you drive normal with a few WOT runs every once in a while. they really suck ass. i've never had to not tighten at least a couple when i check them every other weekend.
Edit: Catch can and a check valve are great "mods", even if you want to keep the car stock for a while. take off the PCV valve and blow thru it both ways.... you'll see why. i don't think blowing 12-14 PSI into your valve cover is a good thing.
- MyNeonSaysHi
- 2GN Veteran
- Posts: 12091
- Joined: Mon May 23, 2005 8:46 pm
- Location: Kansas
Very nicely said Wenuden.
I personally rarely check my clamps. I checked em last week and they were all nice and tight.
T-bolts are a great thing to have. But I don't think it would be a good idea to put them on the intercooler side because its an oval. And worm clamps like circles not ovals so I been told on SRTforums. But they probably would be fine. Just get your worm clamps nice and tight you should be fine. Look for any holes/tears in your plumbing too. Make sure the hoses are completely all the way on. Example's:
Intercoolers sides, hotside pipe, bottom of turbo, throttle body.
Stock PSI according to Dodge stock is 11-14 PSI. I spike 14-13 and it bleeds down to 11-12. Because I know I have a leak coming from my AGP BOV.
It doesn't hurt a car to drive it with a boost leak I do believe. As long as you stay in vac. and don't go into boost.
Like Wenuden said. a catch can and a checkvalve would be a great thing to get. Keeps the boost going one way. Also keeps oil out of the damn intake manifold and your cold side part of the intercooler.
The stock throttle bodies are known to leak. If you think about it, when you do a boost leak test you are shoving air through the system when the car is off... So the throttle body stays shut. So the air just hits the damn throttle body plate and shoves it out wherever it can go. (Sticky on the ModernPerformance vendor thread on SRTforums about boost leak testing, check it out on)
Good luck with everything and ask away.
I personally rarely check my clamps. I checked em last week and they were all nice and tight.
T-bolts are a great thing to have. But I don't think it would be a good idea to put them on the intercooler side because its an oval. And worm clamps like circles not ovals so I been told on SRTforums. But they probably would be fine. Just get your worm clamps nice and tight you should be fine. Look for any holes/tears in your plumbing too. Make sure the hoses are completely all the way on. Example's:
Intercoolers sides, hotside pipe, bottom of turbo, throttle body.
Stock PSI according to Dodge stock is 11-14 PSI. I spike 14-13 and it bleeds down to 11-12. Because I know I have a leak coming from my AGP BOV.
It doesn't hurt a car to drive it with a boost leak I do believe. As long as you stay in vac. and don't go into boost.
Like Wenuden said. a catch can and a checkvalve would be a great thing to get. Keeps the boost going one way. Also keeps oil out of the damn intake manifold and your cold side part of the intercooler.
The stock throttle bodies are known to leak. If you think about it, when you do a boost leak test you are shoving air through the system when the car is off... So the throttle body stays shut. So the air just hits the damn throttle body plate and shoves it out wherever it can go. (Sticky on the ModernPerformance vendor thread on SRTforums about boost leak testing, check it out on)
Good luck with everything and ask away.
08 Acura TL-S
23 Hyundai Elantra N
Ok so underneath everything is fine except the cold side pipe(from IC to TB) has a bunch of oil on the bottom around the clamp.
Here are the shots I could get of the vac lines and the turbo area
Here are the shots I could get of the vac lines and the turbo area
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
the one right after the air box, the one right bofore the turbo, right after the turbo, hot side before the IC, cold side right after the IC and the one right before the TB, all of 'em? I also zip tied all the vac lines.
Man is it fun to drive now though.
Man is it fun to drive now though.
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
- MyNeonSaysHi
- 2GN Veteran
- Posts: 12091
- Joined: Mon May 23, 2005 8:46 pm
- Location: Kansas
Glad you got it man. Your turbo/heatshield/WGA look clean as hell too. I wish I could beadblast my turbo.
All that oil down there is normal. To get rid of it, get a catch can. Very simple easy install.
See that electrical connector? I had that thing pop off before under WOT, watch out for that.
No riceplate. Good. Don't buy one either.
All that oil down there is normal. To get rid of it, get a catch can. Very simple easy install.
See that electrical connector? I had that thing pop off before under WOT, watch out for that.
No riceplate. Good. Don't buy one either.
08 Acura TL-S
23 Hyundai Elantra N
Ok so now sometimes at idle, at a stop light or something, the vacum will be all over the place between 22 and 10, and the engine will chug a bit. Also on the way to the store tonight 1st gear through 3rd, I was speeding up(stop to 40mph) and the power getting to the wheels was lacking for about 2k rpm after the shift and then the whole car would buck and it would have power like normal. It did that for each shift until 3rd to 4th, all the while the boost gauge needle was jumping around in the vacum range. (should I ask about this in tranny?) On the way back from the store it was normal. Spark Plugs fouled?
2005 Red SRT4
Stage 2, Maddog 72-4
Still needs a paint job
Official "I'm Going to Drive My Neon till it Dies" Club #87
- MoxHair
- 2GN Member
- Posts: 3801
- Joined: Mon Feb 27, 2006 5:41 pm
- Location: Atwater, CA; Orlando, FL
- Contact:
I change my Plugs every 6,000miles and my wires every 12,000 miles
You'll be able to tell when it's time to change them when you get a miss or stutter near the top of the rev band.
I use NGK 4306s gapped at .032
You'll be able to tell when it's time to change them when you get a miss or stutter near the top of the rev band.
I use NGK 4306s gapped at .032
2017 Subaru WRX STI
Road Racing > Autocross > Spirited Driving > Sitting in Traffic > Mowing Lawns > Drag Racing
Road Racing > Autocross > Spirited Driving > Sitting in Traffic > Mowing Lawns > Drag Racing