Please help!! installing 15982 Nos switch!
Please help!! installing 15982 Nos switch!
Ive got the magnum intake installed and ready to go.
now it comes down to wiring up the switch!!
ive got the http://www.holley.com/15982NOS.asp
instructions here http://www.holley.com/data/Products/Tec ... 82rev4.pdf
I am only using one relay since the switch is two in one.
Has anyone used this switch before???
i have no idea why im so lost in hooking this up!
PLEASE HELP11
now it comes down to wiring up the switch!!
ive got the http://www.holley.com/15982NOS.asp
instructions here http://www.holley.com/data/Products/Tec ... 82rev4.pdf
I am only using one relay since the switch is two in one.
Has anyone used this switch before???
i have no idea why im so lost in hooking this up!
PLEASE HELP11
Would it be safe to say i wire it similar to this??
http://www.mp3car.com/vbulletin/imageho ... 233622.bmp
(86) Valet switch would be the NOS switch?
(87) would be to Mtv??
http://www.mp3car.com/vbulletin/imageho ... 233622.bmp
(86) Valet switch would be the NOS switch?
(87) would be to Mtv??
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
ya im not all that happy right now considering the seller told me it works and he tested it before i bought it..
i guess i should have tested it before i gave him the cash!!
unless im doing something wrong when i hookup the battery this motor is toast..
ive hit it with som PB blaster to see if it will free up but nothing so far!
EDIT!!!!!!
Motor is not dead is severely seized!!!!!! it did move under 12v power but very very slightly
i have no idea whats going on with this motor, i pulled the plastic cover off and there is no corrosion its nice and clean!
the motor moves a bit more then before!
i guess i should have tested it before i gave him the cash!!
unless im doing something wrong when i hookup the battery this motor is toast..
ive hit it with som PB blaster to see if it will free up but nothing so far!
EDIT!!!!!!
Motor is not dead is severely seized!!!!!! it did move under 12v power but very very slightly
i have no idea whats going on with this motor, i pulled the plastic cover off and there is no corrosion its nice and clean!
the motor moves a bit more then before!
Last edited by Soundwav on Sun Jun 16, 2013 3:21 pm, edited 1 time in total.
-
- 2GN Member
- Posts: 727
- Joined: Thu Nov 17, 2011 11:53 am
- Location: ny
-
- 2GN Member
- Posts: 1019
- Joined: Sun Feb 19, 2006 7:29 pm
- Location: Indianapolis, IN
- Contact:
yes its off the manifold
hooked directly to a small 12v battery
the motor turns about a quater turn then nothing!! and will only turn when its in a certain spot
wont snap back or move any further
does the spring on the end on the motor have enough tension to snap the motor back into closed position?
how far does this motor actually turn??
i can get it to move about a quater turn... im wondering if its turning enough to open the butterflies and the spring will be strong enough to close them
hooked directly to a small 12v battery
the motor turns about a quater turn then nothing!! and will only turn when its in a certain spot
wont snap back or move any further
does the spring on the end on the motor have enough tension to snap the motor back into closed position?
how far does this motor actually turn??
i can get it to move about a quater turn... im wondering if its turning enough to open the butterflies and the spring will be strong enough to close them