Page 1 of 1
Srt4 rear and stock front
Posted: Thu Jan 13, 2011 9:57 am
by NHARINTON88
Searched and can't find the answer. Is it ok if I throw a stock srt4 rear sway bar on my SE? Not sure if it needs to match with the stock front.....
btw, I have tokico blues with Megan springs.
Posted: Thu Jan 13, 2011 10:35 am
by Dylan-00Blue
Yep, it's fine giver 90. But the car is going to rotate very differently so watch out for that the first few day until you are used to it.
Posted: Thu Jan 13, 2011 11:05 am
by NHARINTON88
Dylan-00Blue wrote:Yep, it's fine giver 90..
eh?
Posted: Thu Jan 13, 2011 1:22 pm
by Dylan-00Blue
its a Canadian thing it means go for it
Posted: Thu Jan 13, 2011 1:51 pm
by NHARINTON88
ah gotcha. I was conuzzled
Posted: Thu Jan 13, 2011 2:45 pm
by occasional demons
Nuzzling? No one invited me!
ATM, I am running the exact set up. SRT in the rear, and the SE 20mm in the front. I have very little issues with it. But I am also dropped 1.5" and have 205 50 16 tires. Your results may vary, depending on ride height, and tire size. Each thing changes everything a little bit.
Posted: Thu Jan 13, 2011 8:56 pm
by NHARINTON88
i found a new word! I ment confuzzled, but i like that one better!
I am down 2'', snow tires on right now so tire size is stock
Posted: Thu Jan 13, 2011 10:06 pm
by sidepipe87
I'm planning on doing this but with SXT stock front bar since I don't want to chance breaking the bolts just to put the SRT front bar on. I believe the '03+ front bar is bigger than earlier years due to no rear bar.
Posted: Thu Jan 13, 2011 10:52 pm
by occasional demons
It depends on the trim level. The smaller (original '00/'01) front sway is listed for all years. It could be used with the rear equipped cars tho.
Or those just plain sucked for cornering.
occasional demons wrote:5272327 [SBD] is listed for all years. Base models
4656856AA [SDC] [SDE] [SDF] [SDK] is 2002 and up
4656670AA is 2001 export models. IDK what diameter it is.
SRT is not included there.
Posted: Fri Jan 14, 2011 9:49 pm
by OB
My car came with a 22mm front bar from the factory, which is only 2mm smaller than an SRT. Not sure exactly which ones came with the larger bar, could be 03+ or maybe even less specific. Need more data, everyone go mic your front bars!
Posted: Sat Jan 15, 2011 1:29 am
by NHARINTON88
realized my OP was wrong too.... its on a SXT.
best I can do is a crappy picture so I'm no help
Posted: Sat Jan 15, 2011 5:26 pm
by occasional demons
If you have a set of metric wrenches, you can slide the open ends over the bar to find the diameter.
Does your SXT currently have a rear swaybar?
Posted: Mon Feb 07, 2011 3:04 pm
by NHARINTON88
no rear sway bar. I'll check the size tonight. great idea!
Posted: Mon Feb 07, 2011 3:23 pm
by occasional demons
You will want to check it in the middle where it is straight, as the bends may throw it off a little. Prolly not enough to matter tho.
Posted: Mon Feb 07, 2011 5:19 pm
by OB
As long as you have struts with tabs to accept a rear bar, which all Tokico's do, you can use ANY rear bar designed for ANY 00-05 Neon or SRT-4. You will need the hardware from any model as well. Most people with lowered cars use shorter endlinks, to help make up for the change in geometry. This isn't required but it is a good idea from a performance aspect. Personally, I just shortened my Prothane endlink spacers and used new bolts. Cost me $5 and I was able to customize them to my needs.