Gauges went plop D:
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
Gauges went plop D:
i got on 01 neon es with K&N CAI and i swapped the steelies for SRT-4 rims. so one day in winter get in start it up. and i get almost outta my neighborhood and i notice my speedo isnt working the temp isnt either and my fuel is all bouncy. 20 mins down the road it comes back on. flashes a code and poof they are out again. so i looked on here and i swapped with a 02-03 cluster (thinking that the cluster was bad) and same exact thing. anyone help! need it back asap!
- RobsProjectSOHC
- 2012 Gold Contributor
- Posts: 415
- Joined: Fri Aug 19, 2011 11:36 am
- Location: NY
What is the code that comes up?
Key dance - off / on / off / on / off / on
sounds like a short some where.
Key dance - off / on / off / on / off / on
sounds like a short some where.
Project 003. Just building a Daily Driver with some upgrades.
For Sale Thread | CarDomain | FeedBack
Official "I'm gonna drive my Neon until it dies Club" Member #119
For Sale Thread | CarDomain | FeedBack
Official "I'm gonna drive my Neon until it dies Club" Member #119
- Public Disturbance
- 2GN Member
- Posts: 877
- Joined: Mon Aug 22, 2011 1:38 pm
- Location: Rapid City, SD
Mine did the same thing once disconect your baby reset the pcm and you should be good
FEEDBACK:viewtopic.php?t=60689
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
I'm thinkin he meant battery.
2004 Dodge Neon SRT4 (New beast)
Owner of B&P Repair https://www.facebook.com/pages/B-and-P- ... 9500229160
Owner of B&P Repair https://www.facebook.com/pages/B-and-P- ... 9500229160
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Remove the cluster, and check the connector.
Possibly this code: P1687 No Cluster BUS Message No J1850 messages received from the Mechanical Instrument Cluster (MIC) module
Check
pin 2: PCI bus.
10 ground.
21 and 15 (+)
viewtopic.php?t=38270
Possibly this code: P1687 No Cluster BUS Message No J1850 messages received from the Mechanical Instrument Cluster (MIC) module
Check
pin 2: PCI bus.
10 ground.
21 and 15 (+)
viewtopic.php?t=38270
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester
- Public Disturbance
- 2GN Member
- Posts: 877
- Joined: Mon Aug 22, 2011 1:38 pm
- Location: Rapid City, SD
DAMN Autocorrect.... batteryPublic Disturbance wrote:Mine did the same thing once disconect your baby reset the pcm and you should be good
FEEDBACK:viewtopic.php?t=60689
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
i tried everything checked all the pins, changed clusters again, checked for loose wires, tried even doing a little dance while i did it and nothing..... i know its getting power because the tach goes from sitting on the stopping needle to j
like 1/8 inch above it and you can see it twitch at start up. and all my lights and signals work just fine. its like there's no signal to any of the gauges to move them. gahhh this is getting so aggrivating
like 1/8 inch above it and you can see it twitch at start up. and all my lights and signals work just fine. its like there's no signal to any of the gauges to move them. gahhh this is getting so aggrivating
-
- 2GN Member
- Posts: 3371
- Joined: Wed Mar 14, 2007 4:50 pm
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
It is prolly in the PCI bus circuit.
Violet/Yellow wire.
All the gauges are run through one wire (PCI Bus) via the PCM. Except the fuel, it is directly connected to the sender. The gauge does communicate via the PCI with the PCM tho.
Like he said, check the PCM connectors, any spots where the wires could be chafed.
Violet/Yellow wire.
All the gauges are run through one wire (PCI Bus) via the PCM. Except the fuel, it is directly connected to the sender. The gauge does communicate via the PCI with the PCM tho.
Like he said, check the PCM connectors, any spots where the wires could be chafed.
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester
-
- 2GN Member
- Posts: 1019
- Joined: Sun Feb 19, 2006 7:29 pm
- Location: Indianapolis, IN
- Contact:
- l3utteredTOAST
- n00b
- Posts: 17
- Joined: Sun Dec 18, 2011 8:32 pm
Yea it was my ecu. I pulled one from an identical neon and it fixed it. But by that time I swapped the cluster for one with a tach and it was well worth it if you don't have one.tursh2010 wrote:Did you figure out your problem? My car is doing the exact same thing except now none of the gauges work. I will check out my yellow and violet wire tomorrow now that I know exactly which wire to look at.
-
- Junior Admin
- Posts: 20306
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Hopefully you don't have SKIM, or the replacement PCM either.(Gray key)
Bill
1999 neon coupe 2.4 swap
2021 Forester
2000 Neon MTX swap with '02 R/T PCMOlha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
1999 neon coupe 2.4 swap
2021 Forester