wheel bearing done

alsey_seven · Post by **alsey_seven** » Sun May 16, 2010 7:45 pm

replaced both side yesterday
Total cost 80.00

will post pics later

FAC3L3SS · Post by **FAC3L3SS** » Sun May 16, 2010 7:48 pm

sidepipe87 · Post by **sidepipe87** » Sun May 16, 2010 8:55 pm

what the fuck is a whell?

FAC3L3SS · Post by **FAC3L3SS** » Sun May 16, 2010 8:58 pm

Know what else is good about this thread? Aside from the fact that pictures will likely NOT ensue, it's a freaking whell bearing, which is a FIX, and it's a hidden one at that. Aftermarket wheel bearing to see performance gain? In for the dyno chart.

MyNeonSaysHi · Post by **MyNeonSaysHi** » Sun May 16, 2010 8:58 pm

well

OB · Post by OB » Sun May 16, 2010 11:32 pm

Can't wait to see the guaranteed-amazing pictures of these glamorous whell bearings.

DOSneons · Post by **DOSneons** » Sun May 16, 2010 11:55 pm

IM SO EXCITED

i think i might pee myself

alsey_seven · Post by **alsey_seven** » Mon May 17, 2010 12:18 am

LOL ya very funny guys. I must have forgotten to proff... read the headline anyways here are the pix's

Tools used
Sliding hammer
Wheel bearing R/R kit from harbor frieght
Snap-On cordless 380 pounds impact gun

I really didn't need a shop press

One thing i can say ride feels new again

BlackRT? · Post by **BlackRT?** » Mon May 17, 2010 2:52 am

Neato dude! 10hp mod huh?

alsey_seven · Post by **alsey_seven** » Mon May 17, 2010 3:41 am

lol i think this part raised my cars Hit points from 50 to 80 for massive damage

SlvrACR · Post by **SlvrACR** » Mon May 17, 2010 6:54 am

Hope it lasts longer then my last set. I whole month before they were making noise again

r/tguy02 · Post by **r/tguy02** » Mon May 17, 2010 7:22 am

i hope you greased those bearings, they look dry in that pic

vincer20 · Post by **vincer20** » Mon May 17, 2010 7:25 am

how do you like the impact gun compared to a air gun?

j-king · Post by **j-king** » Mon May 17, 2010 10:35 am

same thing i had to do like 2 months ago

boy was it a bitch for me

did you have any trouble at all?

alsey_seven · Post by **alsey_seven** » Mon May 17, 2010 3:00 pm

with the tools i used it was fast each side only took me 1 hour to complete each side

the snap-on impact gun works so much better then air gun.
i have three month warranty so if anything goes wrong i will switch them out asap if it happens

MyNeonSaysHi · Post by **MyNeonSaysHi** » Mon May 17, 2010 6:26 pm

SlvrACR wrote:Hope it lasts longer then my last set. I whole month before they were making noise again

IF the hub is bad it will wear out the bearings quicker.
OEM Mopar bearings? I replaced my drivers side 2 years ago, still holding up good.
I am getting my knuckle powdercoated when I do it again.
Great work though.

Post by **racer12306** » Mon May 17, 2010 6:39 pm

This thread has delivered.

Post by **occasional demons** » Mon May 17, 2010 8:43 pm

FAC3L3SS wrote:. Aftermarket wheel bearing to see performance gain? In for the dyno chart.

There you have it: Balls Out Performance.