(_SxXxT_) 7/15/13. The car runs
Today I finished everything up....
And the vertic on everything I did for the front??
Two thumbs up.
Here's a pic of all the crap that was on the car.
If ne wants ne of it I'll pretty much give it away.
Had some extra time to kill while I let my alarm remote charge.
Put back together adjusted Nd on the ground
And I also cleaned between my doors. With no splashguards they get really bad.
Now... Good Friday weekend Im gonna donthe rear... Then time for alot of body work... Yay!!! My specialty...
And the vertic on everything I did for the front??
Two thumbs up.
Here's a pic of all the crap that was on the car.
If ne wants ne of it I'll pretty much give it away.
Had some extra time to kill while I let my alarm remote charge.
Put back together adjusted Nd on the ground
And I also cleaned between my doors. With no splashguards they get really bad.
Now... Good Friday weekend Im gonna donthe rear... Then time for alot of body work... Yay!!! My specialty...
looks good but the breaks look sooo small behind the rims
- Custom or Nuthin -
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-
- 2GN Member
- Posts: 4137
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
-
- 2GN Member
- Posts: 4137
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
had to stop, sun started to go down, and i needed caliper bolts so tomorrow ill finish everything up.. gotta wake up real early.
here we have the modernperformance rear trailing arm...... do not buy it unless yours is rusted or gone bad some how.. its the same.
rubber coated each inner wheel well and under side.
here we have the modernperformance rear trailing arm...... do not buy it unless yours is rusted or gone bad some how.. its the same.
rubber coated each inner wheel well and under side.
-
- 2GN Member
- Posts: 4137
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
-
- 2GN Member
- Posts: 4137
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
like the trunk lid
- Custom or Nuthin -
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-
- 2GN Member
- Posts: 199
- Joined: Mon Mar 28, 2011 12:27 pm
- Location: Columbia, MO
-
- Spam Avenger!
- Posts: 9003
- Joined: Wed Aug 02, 2006 2:49 am
- Location: Kokomo, IN
-
- 2GN Member
- Posts: 1006
- Joined: Mon Oct 13, 2008 8:19 pm
- Location: Akron oh
so i know this has ben asked before but any plans for wider wheels??
i mean if you get a set of wider wheels to sit just flush with your fender flares it would set this car off so bad you have no idea
i mean if you get a set of wider wheels to sit just flush with your fender flares it would set this car off so bad you have no idea
2004 white dodge neon 2.4 DOHC swapped
2004 red dodge neon srt-4 gone
2000 flat black plymouth neon 2.0 DOHC swapped gone
2002 silver dodge neon parts car R.I.P
2000 green dodge neon parts car R.I.P
sweet and these wheels look good its just that since the wheels look too sunk in cause of the fenders.. or get some big adapters to push them out
2004 white dodge neon 2.4 DOHC swapped
2004 red dodge neon srt-4 gone
2000 flat black plymouth neon 2.0 DOHC swapped gone
2002 silver dodge neon parts car R.I.P
2000 green dodge neon parts car R.I.P
So I got the weekend off nd now iv been workin to get my body work finished.... Here's where I'm at.
Iv also been playing around with the flat black and semi gloss look.... Here's what i got
4 parts flat 1 part reducer 1 part gloss harder
This is the semi gloss
The First picture is gonna b one side semi gloss the next picture will b oppisite side will b just flat.
Semi
Flat
Tell me what u think
Iv also been playing around with the flat black and semi gloss look.... Here's what i got
4 parts flat 1 part reducer 1 part gloss harder
This is the semi gloss
The First picture is gonna b one side semi gloss the next picture will b oppisite side will b just flat.
Semi
Flat
Tell me what u think