2GN.ORG

You need to get this log off of page one. So on to page two.

Is it just me, or are there actually no pictures of Viper seats?

Adam, scroll down the first page.. youll see them.

I was bored today so i pulled my car into the garage to do a job i have been putting off for a while. Now granted me and my dad are not professinals but we did alright for 2 hours and spray paint. I decided to do this to protect my car from rust and wait until i get enough money to have it done professinally. so here are the pics


the original damage














i have to wait a few more days for the paint to fully cure before i wet sand and buff the line out of the fender.

Not too bad, good job

For an amateur, it looks fine. Good job.

thanks!! im going down now to put the light back in and clean it up..then ill take another shot just for ha ha's

looks good man, defanitely better then it did

here are the pics with the headlights back in.

thats really not that noticeable at all bro

good job!!

yeah but im going to try to make it better probably in 2 days. ill buff it and wet sand it with 1200 or higher grit paper.

and i need a set of eyelids haha

Go with 2000.....no coarser..that's spray paint not cured urethane enamel.

I hate to bust your balls, but those lines are DISTINCT AS HELL.

The blue maybe the same, but there seems to be horrid overspray.


Not good

Of course it's distinct, he hasn't buffed or wetsanded yet. That's where the blend will come from and it shouldn't be TOO noticeable afterwards...

yeah i just got wait till its totaly cured before i go mess with it. but i hope it will be better..its deff better then the rust i had before so im happy and like i said im not a professinal

looks good man

anyone got any good ideas i can do to my car that doesent cost any money.haha im broke lol

Wow, great job on the fender! Almost look like new.

Steven, can you do any better? lol

thanks! im going to work on it a bit more tho

Tam wrote:Wow, great job on the fender! Almost look like new.

Steven, can you do any better? lol

I never said I was a painter. I was just saying that it was a distinct line.

And if your mad for some reason about the lines, then don't post them unfinished I guess, I mean the paint is very close and good there, but you can straight up see the lines dude.

I mean you said it's a work in progress, I understand that to the fullest, just don't get butthurt about it when someone tells you this on an UNFINISHED project. I'm sure it will turn out great.

If you blended that spot with the paint and cleared the whole fender, you wouldn't have a line in it. To be truthfull sanding the spot will make it worse, you'll end up going through the clear on the edge of it and a couple months down the road you'll see the remaining clear slowly and slowly become cloudy and peeling along the spot. The only real way to fix that fender is to have it blended and have the whole fender recleared.

Also, after you primed that spot, did you remove the tape to sand the primer smooth and flush to the rest of the fender? Or did you just paint over the unsanded primer?

I'm not trying to criticize your work but it could've been done better

To the untrained naked eye you wouldn't be able to tell there was even a line theremm but you did do a good job afterall..I'm sure with some buffing and sanding that it should look a little. Better.

srtgtr34 wrote:If you blended that spot with the paint and cleared the whole fender, you wouldn't have a line in it. To be truthfull sanding the spot will make it worse, you'll end up going through the clear on the edge of it and a couple months down the road you'll see the remaining clear slowly and slowly become cloudy and peeling along the spot. The only real way to fix that fender is to have it blended and have the whole fender recleared.

Also, after you primed that spot, did you remove the tape to sand the primer smooth and flush to the rest of the fender? Or did you just paint over the unsanded primer?

I'm not trying to criticize your work but it could've been done better

we sanded down the primer flush and tried to get the edges as smooth as possible..idk if sanding it will make it any better i just wanted to make it better then the rust until i had enough money to have someone repaint the whole fender. and i did it with spray paint so i wasent expecting it to come out perfect

now i gota paint my grill mesh and my hood mesh black so it dont stick out so much

I decided to do this to protect my car from rust and wait until i get enough money to have it done professinally. so here are the pics

Some people don't read.

Great job man, looks 10X better than what it did.
Definately paint that mesh, it does stick out like a sore thumb.

Maybe colormatch the foglight bezels?

yeah i thought about it painting the fog bezels but they kinda match my black and blue theme haha

heres a pic of the rest of the car that i fixed already and why my fender was damaged as you can see it was alot worse the the pic above..i had bent it back and hammered it back to kinda the right shape.

I think you should get CF fog bezel's. Match your hood

yeah i probably will end up getting CF at some pont down the road.

dude you scared the shit out of me with that picture, i was thinking "no, not again"

haha no that was from the crash before lol. i hope it never happens again.