2GN.ORG

Legal ride height in ca is the 23" from the floor to the center of the headlight. That's the lowest it can be. Are you going to powdercoat them.

yep im lower. and yes i will coat them; either gloss white, or gold.

thinking about wrapping my hood in this vinyl; if i can get a large enough piece.

Hideous...

nobody asked you fat man

TheRandom1 wrote:Hideous...

we can't all appreciate the female form, would you prefer urban camo penis's?

i think it's baller.

I like the female form, but it's the cammo I think is hideous. Especially on a hood...

It wouldn't be as bad if you wrapped your headliner and door inserts in that, but why on the hood? I don't get it.

i plan on doing that too. i honestly don't care what you guys think anyway, its my car and my own personal style. thanks for the comments though.

went to the junk yard today. I picked up a 95 sohc wiring harness, a ton of connectors and a single fan radiator shroud.

i'm getting excited as the swap list gets closer to being complete.

proud new owner of these!



obviously i will not put them on looking this shitty. a few coats of powdercoat is in store for them.

damn... I've actually been thinking about picking a set of those up and doing them some bright ass color but I haven't seen any locally for cheap. I pass this sunfire by my apt sometimes with some on it and it look pretty good. GTZ wheels ftw. PS they look really good polished!

thanks ryan? i am still unsure of a color. they may just go white again. i don't want to draw too much attention to the car with flashy colors that scream "pull me over"

Yeah I hear ya. The white will actually look really nice I think.

might try some new powder. we shall see. something like this....


http://www.powderbuythepoundwest.com/ca ... ts_id=1097

and this clear
http://www.powderbuythepoundwest.com/ca ... cts_id=159

I love the wheels, i cant wait to see them on. i kinda want a set of Fiero gt mesh wheels for my coupe...

thanks for the support mang. i think it looks tight, but in small doses.

can anyone shop the pugeot's camo onto my hood and paint the roof black?

http://www.tirerack.com/tires/tires.jsp ... mpare1=yes

hmmmm

bump so i can find this.

put in a new radiator and thermostat today. hopefully it clears up my overheating issue.

going to have some big updates in the next couple of weeks.

hybrid-Srt2001 wrote:bump so i can find this.

ahahahaha


I can haz big updates too?

what have we here?


oh almost tucking rim

had to do some work to get this to happen. no tearing up brand new tires for me







also rolled the fender


this is with an 8mm spacer.

this post will only matter once they are officially mounted on the car. GO

waiting on tires and powdercoat to get here =(

Im going to be tubbing my front end like you have done there also so i can be dirty low and tucking my 24.5/8.5 slicks

Gonna need more spacerz Seanzie. Flushness awaits...

max i can do with these wheel studs is 13mm. they are from a 98 ford taurus and are 10mm longer than stock. only 30 bux for 10 vs the 60 for arp.

I'm sure you've posted, and they aren't factory, but what strut body are you using? I've got some Mopar S3 coils that I want to stiffen up, and those QA1 springs are legit and well-priced. I'm thinking of grabbing maybe 400f / 350r. Are yours 2.5" or 2.25"? I know 2.25" is too small, but I've also ready that 2.5" can be a little big.

these are factory struts that have been modified. I cut them down to keep them from bottoming internally and blowing. They have handled the springs suprisingly well; it is just a very bouncy ride because of the lack of dampening. These springs really need a set of konis, but i don't like the idea of spending $500 and cutting them up. The springs are standard 2.5" id iirc. It's the standard coil over sleeve size.

Alright cool. I'll check mine over when they get in this week, but I wanted to be sure. I didn't realize how cheap new springs were