"Nikki" 02 R/T Big Power Boost Build!

OhNoA2.0 · Post by **OhNoA2.0** » Fri Mar 22, 2013 2:30 am

Boosted22sxt wrote:not sure how much power you looking to hold.... but eBay sells ban off clutches Im using there six disk and on 18 psi has not weakened... I have never launched with slicks only sticky street tires.

I just ordered another CM stage 4. It was most likely the wheel hop off the line that killed my old one. That's my fault for being on a stock suspension. The break in period will give me a little time to get a decent pair of struts under the front, maybe even lower it a little.

OhNoA2.0 · Post by **OhNoA2.0** » Thu Apr 11, 2013 12:20 am

After a few mishaps, finally got my new clutch. CM S4! Hopefully throwing it in tomorrow along with a new drivers side axle. Woo!

Neon4Life · Post by **Neon4Life** » Thu Apr 11, 2013 6:21 am

^how much did that cost.

OhNoA2.0 · Post by **OhNoA2.0** » Thu Apr 11, 2013 9:39 am

416 shipped from Modern. Cheapest price out there. I almost bought 2. haha

Neon4Life · Post by **Neon4Life** » Thu Apr 11, 2013 2:39 pm

Dam. That is a good price. Should have bought 2. 1 for backup. Lol.

NGCnoproblem · Post by **NGCnoproblem** » Thu Apr 11, 2013 11:18 pm

Dang thats a great price

Boosted22sxt · Post by **Boosted22sxt** » Fri Apr 12, 2013 9:00 pm

I'd really like to know what pressure plate the Bahnhoff clutches use because the disk is def a clutch masters because mine has the same green sticker on the disk..

Post by **occasional demons** » Fri Apr 12, 2013 9:05 pm

That SFI sticker is used for numerous stuff. It is just a certification sticker. It is not specific to any one manufacturer.

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for specialty/performance automotive and racing equipment.

http://www.sfifoundation.com/

Boosted22sxt · Post by **Boosted22sxt** » Fri Apr 12, 2013 11:58 pm

I see my flex plate on my mustang has that but its a lot larger and holographic looking... with numbers removed like dates on a battery. I can't zoom his pic in is that really an sfi sticker.

OhNoA2.0 · Post by **OhNoA2.0** » Mon Apr 15, 2013 12:51 pm

Boosted22sxt wrote:I see my flex plate on my mustang has that but its a lot larger and holographic looking... with numbers removed like dates on a battery. I can't zoom his pic in is that really an sfi sticker.

Yes, it's an SFI sticker

And time for an update

I picked up a dual exhaust rear section from UriahRR over the past weekend and modified it to fit my existing catback so that my single and dual exits are now interchangeable depending on how loud/ignorant I want to be

I polished it up a bit and it looks great. I'm going to bring the tips another 1/2" higher when I get some more time to cut/weld.

What do you guys think?

Sorry for the crappy cell phone pics. I'll replace them with some nice HD photos when I get a chance

OhNoA2.0 · Post by **OhNoA2.0** » Sun May 12, 2013 10:21 am

Finally got myself a solid lower mount. Massive!

INVUJerry · Post by **INVUJerry** » Sun May 12, 2013 11:34 am

Rear section looks great, what is your other muffler?

OhNoA2.0 · Post by **OhNoA2.0** » Sun May 12, 2013 8:06 pm

Ebay single exit

r/tguy02 · Post by **r/tguy02** » Mon May 13, 2013 7:27 am

yay for the motor mount

OhNoA2.0 · Post by **OhNoA2.0** » Tue Jun 11, 2013 10:10 am

Here's a clip of my first official track run. I was still trying to adjust launching rpm and tire pressure but ran into some "technical difficulties" on my 3rd run. Still not bad, but I've got plenty of room to improve.

Video creds to Jake Probst

Enjoy

http://www.youtube.com/watch?v=h1_HrE3q ... ata_player

ThatKevin · Post by **ThatKevin** » Tue Jun 11, 2013 4:58 pm

12.82.. wow

NGCnoproblem · Post by **NGCnoproblem** » Tue Jun 11, 2013 10:55 pm

Once u get your 60 foot down I bet ull be in the 11s

OhNoA2.0 · Post by **OhNoA2.0** » Wed Jun 12, 2013 9:02 am

If I can get a 1.7 60', I should pull an 11.80ET

OhNoA2.0 · Post by **OhNoA2.0** » Mon Aug 05, 2013 4:14 pm

Just got my AGP Race BFMIC! I'm going to fab up my own crash bar.

Time to cool things down a bit then crank up boost once I get my 4bar MAP sensor.

Everything ripped apart

Painted the surrounding area black to clean up things up a bit

Had to trim a little extra to make it fit but she looks good!

OhNoA2.0 · Post by **OhNoA2.0** » Thu Aug 08, 2013 11:45 am

Crash bar is made and installed! I think it came out pretty well.

r/tguy02 · Post by **r/tguy02** » Fri Aug 09, 2013 8:12 am

crash bar looks good ryan

Neon4Life · Post by **Neon4Life** » Fri Aug 09, 2013 12:36 pm

that BFMIC looks sweet.

OhNoA2.0 · Post by **OhNoA2.0** » Sat Aug 24, 2013 1:32 am

Out with the old, in with the new

The ports on this thing are ridiculous!

7654800neon · Post by **7654800neon** » Sat Aug 24, 2013 9:12 am

On your video of you at the track what tire and size are you running on the front

OhNoA2.0 · Post by **OhNoA2.0** » Sat Aug 24, 2013 10:01 am

22x8x15 Mickey Thompson slicks

OhNoA2.0 · Post by **OhNoA2.0** » Mon Aug 26, 2013 12:03 pm

I took the time yesterday to install the new manifold. It looks so great, I couldn't be happier with it! I also got everything else back together and took her for a spin. My old manifold was deff a bit restricting. I'm spooling around 4200 now, opposed to 4500 and top end deff pulls harder.

GroceryGetter · Post by **GroceryGetter** » Thu Sep 12, 2013 10:35 pm

I hope I could one day build a car like this.

7654800neon · Post by **7654800neon** » Fri Sep 13, 2013 8:50 am

How much that manifold run I have the same one as your old one

OhNoA2.0 · Post by **OhNoA2.0** » Fri Sep 13, 2013 10:04 am

GroceryGetter wrote:I hope I could one day build a car like this.

Thanks man. She's come a long way but she still has a journey ahead of her lol.

7654800neon wrote:How much that manifold run I have the same one as your old one

http://aspturbo.com/store/product_info. ... ucts_id=93

Worth every penny!

GroceryGetter · Post by **GroceryGetter** » Sat Sep 14, 2013 12:57 am

I saw a guy on Facebook who is building a pretty wicked SOHC as well. He has a pretty big turbo on the way and something about a surprise manifold. You seen it? Guy seems like he may know what he is doing.

2GN.ORG

"Nikki" 02 R/T Big Power Boost Build!

What color should i powdercoat my intake manifold? (My valvecover will be metallic gold)