2gn atx guys

95srtswap · Post by **95srtswap** » Mon Sep 16, 2013 12:17 am

Who's all rocking a atx 2gn? Thinking about making a performance calibration

gtxtreme19 · Post by **gtxtreme19** » Mon Sep 16, 2013 11:08 am

I'm sure lots have them but probably not many modding them. Most are mtx swapping before starting heavy modification, usually the first words out of any mouths here are "mtx swap it." I doubt it would be worth your time

Post by **occasional demons** » Mon Sep 16, 2013 12:02 pm

There are a few die hard ATX folks out there. Plus the ones that can't swap, due to Significant Others/spouses, or disabilities.

I wouldn't go so far as to say it isn't worth delving into, there just may not be a huge volume is all.

On the flip side, ATX's need all the help they can get. Would this be for both 31th, and 40/41te? Tho 31th would be much closer to the MTX setups.

C1DoG · Post by **C1DoG** » Mon Sep 16, 2013 4:12 pm

How much more performance are you thinking you can get?

NickKo · Post by **NickKo** » Fri Sep 20, 2013 4:05 pm

95srtswap wrote:Who's all rocking a atx 2gn? Thinking about making a performance calibration

Hi, Kevin !!

Are you talking about the 2000-2001 3-spd ATX ??
Or the 2002-up 4-spd. ATX ??

- Nick

95srtswap · Post by **95srtswap** » Fri Sep 20, 2013 6:57 pm

NickKo wrote:
95srtswap wrote:Who's all rocking a atx 2gn? Thinking about making a performance calibration
Hi, Kevin !!

Are you talking about the 2000-2001 3-spd ATX ??
Or the 2002-up 4-spd. ATX ??

- Nick

Both

NickKo · Post by **NickKo** » Fri Sep 20, 2013 7:26 pm

95srtswap wrote:
NickKo wrote:
95srtswap wrote:Who's all rocking a atx 2gn? Thinking about making a performance calibration
Hi, Kevin !!

Are you talking about the 2000-2001 3-spd ATX ??
Or the 2002-up 4-spd. ATX ??

- Nick

Both

Excellent !!

For the ATX haters out there -
A modded ATX, will almost never be as quick as an MTX - 'all things being equal'.
HOWEVER - This does not mean, that the performance of an an ATX Neon, can't be improved !!

I once tried running a MoPar Performance PCM, on my old 1995 ATX SOHC Neon.
I will say that I was pleased with the results.

It was still not as quick as my MTX Neon, but throttle response was noticeably improved, and the engine was much more responsive.... In other words, the 'fun to drive' quotient was much better.

Just don't expect your ATX Neon, to become a flaming fast hot rod.

But a PCM on an ATX, will definitely help it 'perk up' quite a bit.

- Nick

Post by **occasional demons** » Fri Sep 20, 2013 7:49 pm

Just the mildly ported head on our '96 helps out once you get some RPM going. It certainly pulls better than the un ported head did. All else is stock, even the cam.

Altho it is a 10.3:1 C.R., it is all stock factory parts.

titansxt · Post by **titansxt** » Sat Sep 21, 2013 2:36 am

Reading > Me.

I just sent a PM. Haven't done a swap yet as I need a clutch and a few misc parts to install it but I'd LOVE a smooth ATX in my 03 in the mean time!

Ramroid · Post by **Ramroid** » Sat Sep 21, 2013 3:18 am

I'm a die hard atx man. Mainly because my left leg can't handle the back and forth motion of the clutch. Thanks to a combination of a reconstructed ACL and and old lady who decided to side swipe me over a 20' cliff, my left leg sucks.

I remember reading somewhere(don't remember) that mopar made a shift tune for some atx's. Can't remember where I read it tho.

aceborn · Post by **aceborn** » Sat Sep 21, 2013 3:22 am

Do you think you'll have this cal done for 00-01 31th by the time you start your group buy?

Any idea of the hp gains?

Either way I want one so bad

NickKo · Post by **NickKo** » Sun Sep 22, 2013 1:58 pm

Ramroid wrote:I'm a die hard atx man. Mainly because my left leg can't handle the back and forth motion of the clutch. Thanks to a combination of a reconstructed ACL and and old lady who decided to side swipe me over a 20' cliff, my left leg sucks.

I remember reading somewhere(don't remember) that mopar made a shift tune for some atx's. Can't remember where I read it tho.

You must be referring to the 'Performance Automatic' valvebody for the 3-spd. ATX:
http://www.allpar.com/forums/topic/6918 ... alve-body/
I don't recall, if these were offered through the MoPar Performance Catalog, or not.

Unfortunately, I believe these have been discontinued.

However - It is actually fairly simple, to 'build' your own shift kit, thanks to the information posted on-line by those sick Turbododge fiends, and 'Mookie' and his D.I.Y.-shift kit link.

- Nick

95srtswap · Post by **95srtswap** » Fri Sep 27, 2013 2:36 am

I got an 01 ATX cal modeled from my Dyno tested MTX cal.

Post by **occasional demons** » Fri Sep 27, 2013 8:54 am

There is a stage 1 shift recalibrate, or something to that effect for the GT Cruisers with the 41te. I ran across it once searching for something else on the web.

NickKo · Post by **NickKo** » Sat Sep 28, 2013 9:32 pm

occasional demons wrote:There is a stage 1 shift recalibrate, or something to that effect for the GT Cruisers with the 41te. I ran across it once searching for something else on the web.

Interesting !!
I wonder how difficult it would be, to install it... ahem.

- Nick

2GN.ORG

2gn atx guys

2gn atx guys

Re: 2gn atx guys

Re: 2gn atx guys

Re: 2gn atx guys

01 ATX cal Done