Part Number Request: Magnum intake manifold parts

TwistedTunerz · Post by **TwistedTunerz** » Wed Apr 22, 2009 12:19 pm

As the title said, bought an R/T kid thought it would get better performance by taking the butterfly plates out of the manifold, need to know if you can get the butterfly plates and screws and if so part numbers, still has everything else just no plates or screws. Thanks in advance

Post by **occasional demons** » Wed Apr 22, 2009 12:39 pm

Part Number: 4884065AE List Price $388.00 Fuel system - Fuel induction - Intake - Intake manifold Intake manifold, neon, sohc, all 2002

Part Number: 5018787AC List Price $266.00 Fuel system - Fuel induction - Intake - Intake manifold Intake manifold, neon, sohc, all, 2.0l, w/high output 2003 - 2005

Part Number: 4884094AB List Price $166.00 MOTOR MANIFOLD TUNIN

Part Number: 4884067AB List Price $12.10 GASKET INTAKE PLENUM

Part Number: 4648623AB List Price $4.65 Fuel system - Fuel induction - Intake - Manifold gasket Manifold gasket, neon, sohc, w/rt 2001 - 2005

Part Number: 6102041AA List Price $0.35 SCREW

Part Number: 6506575AA List Price $2.00 SCREW

IDK if the plates/screws are available seperately. Someone on here made their own. There is a post with pics/info, so with the right key words, a search might turn it up.
PM BRR or Dante, they may be able to get that info. And post that in here for future reference if you do obtain some info.

BlackRoseRacing · Post by **BlackRoseRacing** » Sat May 02, 2009 5:31 am

butterfly plates and shaft are serviced with the lower manifold only

ragek23 · Post by **ragek23** » Tue Aug 18, 2009 12:20 am

whats the PN for the actuator motor?

ZeroChad · Post by **ZeroChad** » Tue Aug 18, 2009 1:26 am

I think the first page of my project log has pics of the ones I made. There is also a post talking about the correct screw size floating around somewhere.

Post by **occasional demons** » Tue Aug 18, 2009 9:48 am

ragek23 wrote:whats the PN for the actuator motor?

In the post above

Part Number: 4884094AB List Price $166.00 MOTOR MANIFOLD TUNIN

Maddog · Post by **Maddog** » Tue Aug 18, 2009 11:00 am

If someone with access can pull a screw from their Magnum IM, and measure the threads (I believe they are M6x1.00), the thread length, and the hex, you could probably take that info to a hardware store and get the screws for half or less than half that price. I'd do it now, but all my Mag IMs are at home

Also, FelPro sells the gasket set (plenum to runners, and runners to head) for around $6 - not sure if that is any better than OEM - I'm using it, and so far, it works fine.
If you go to a dealer, and tell them what you need, most are kind enough to write the P/Ns down for you. Just make sure you tell them that it is for the "F" code motor

Post by **occasional demons** » Tue Aug 18, 2009 11:54 am

I think ZeroChad was talking about the screws that hold the butterfly plates on. IIRC it was 3mm. I must not be entering the proper search terms, because I know the thread was/is out there.

Maddog · Post by **Maddog** » Tue Aug 18, 2009 4:11 pm

occasional demons wrote:I think ZeroChad was talking about the screws that hold the butterfly plates on. IIRC it was 3mm. I must not be entering the proper search terms, because I know the thread was/is out there.

Oh!

I can get that info, too.

ragek23 · Post by **ragek23** » Tue Aug 18, 2009 7:41 pm

damn thats soo expensive! I better just take the butterflies out for now.

Post by **occasional demons** » Wed Aug 19, 2009 8:12 am

Why? Just move them to the open position, and put some duct seal (putty) on the lever. It won't move, and it is easier to revert to normal operation when you can find a motor used/cheaper. You could remove the link spring from the motor and bolt it back on to keep things clean.

ragek23 · Post by **ragek23** » Wed Aug 19, 2009 5:08 pm

good idea^

Danteneon · Post by **Danteneon** » Thu Aug 20, 2009 1:28 pm

Just for reference, the part # for the screws that attach the MTV motor is 6101221...MSRP $1.00 each.

No size specs on them though

As it turns out, that same screw is used in other Chrysler products. It is used to hold the lower outer timing belt cover to the block on 01 and 02 2.4 Caravans, as well as attaching the front ABS sensors on Dakota and Durangos.

Post by **occasional demons** » Fri Aug 21, 2009 4:59 pm

Plenum to runner screws: M6 x 1.00 x 25mm

MTV motor attaching screws: M6 x 1.00 x 12mm

NickKo · Post by **NickKo** » Sun Aug 23, 2009 12:21 am

occasional demons wrote:Plenum to runner screws: M6 x 1.00 x 25mm

MTV motor attaching screws: M6 x 1.00 x 12mm

Cool, Thanks !!

- Nick

INVUJerry · Post by **INVUJerry** » Sun Jun 03, 2012 5:50 pm

Might have a line on a magnum intake, but the MTV solenoid is missing. I'd like to use it correctly so is it possible to get one of these seperately??

Post by **occasional demons** » Sun Jun 03, 2012 10:29 pm

Yeah, but IIRC, the last of the oem stock is about gone.

4884094AB $174.00

viewtopic.php?t=41287

INVUJerry · Post by **INVUJerry** » Mon Jun 04, 2012 3:56 pm

Jesus, $174. I just pooped.

Adam G · Post by **Adam G** » Mon Jun 04, 2012 6:34 pm

ill sell you one for 150 its still on my mag manifold

INVUJerry · Post by **INVUJerry** » Tue Jun 05, 2012 3:35 pm

We'll see what happens Adam, might just do the trade deal then sell this slightly broken one and buy yours.

2GN.ORG

Part Number Request: Magnum intake manifold parts

Part Number Request: Magnum intake manifold parts

MTV actuator motor?