Part Number Request: Clutch pedal bushing ?

Post Reply
User avatar
ltr450r
2GN Member
Posts: 141
Joined: Sat Jan 16, 2010 9:37 pm
Location: Eastern NC

Part Number Request: Clutch pedal bushing ?

Post by ltr450r » Tue Nov 09, 2010 2:36 pm

This is for a 2005 SXT with manual 5 speed. I need the part number for the two axle seals.

And I need the part number for the bushing piece that connects the clutch pedal to the clutch master cylinder rod.. Its number 5 in the pic below I believe.. Thanks
Image[/img]
Last edited by ltr450r on Sun Nov 21, 2010 2:01 pm, edited 1 time in total.
-Adrian
Image
2003 SXT, MTX

occasional demons
Junior Admin
Posts: 19312
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Tue Nov 09, 2010 6:33 pm

4670265 BUSHING, Hydraulic Clutch Actuator $9.75

4761107 SEAL, Axle Drive Shaft
Part number 4761107 was superceded by part number CS04797334.
No Part Found
$0.00
:tardbang:

So, from the '01 parts listing:


4797334 SEAL AXLE DRIVE SHAFT $9.60

Pretty sure they are the same seal. Just verify with the parts guy. AFAIK, the t350, or axles haven't changed.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

User avatar
ltr450r
2GN Member
Posts: 141
Joined: Sat Jan 16, 2010 9:37 pm
Location: Eastern NC

Post by ltr450r » Tue Nov 09, 2010 6:37 pm

ok yeah for the axle seals he said there were two transmissions showing, a SR5 and a SRS or something like that. He needed my vin but i swapped to the 5 speed so I have no vin..

But Thanks i'll see if he can tell me if the seals are the same
-Adrian
Image
2003 SXT, MTX

User avatar
ltr450r
2GN Member
Posts: 141
Joined: Sat Jan 16, 2010 9:37 pm
Location: Eastern NC

PN Request: Clutch pedal bushin piece

Post by ltr450r » Sun Nov 21, 2010 2:00 pm

Image

I ordered number 5 in the picture but it was only the bushing. I need the piece (marked by green arrow ^^) that the bushing goes into. The screw #4 holds this piece on. Can you buy just this piece or do you have to buy the whole actuator?

THanks
-Adrian
Image
2003 SXT, MTX

Themaggots
2GN Member
Posts: 393
Joined: Fri Jan 11, 2008 3:12 pm
Location: Quebec, Canada

Post by Themaggots » Sun Nov 21, 2010 5:48 pm

They come with the clutch master cylinder. RageTek sells a billet aluminium one but AFAIK, they're not in stock and won't be for a while. Ask on Realtune's website for approximate dates.
Jimmy

occasional demons
Junior Admin
Posts: 19312
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sun Nov 21, 2010 9:40 pm

Vendor on SRT forums: LCR but they may still be sold out also.

Image
For questions or inquires feel free to email us at:

Sales@lepolesconceptsracing.com

Shop Phone: 330-221-4857

If you are sending us your parts or returning a core please ship to:

Lepoles Concepts Racing

2757 Shadley St.

Streetsboro, OH 4424
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Mon Nov 22, 2010 11:03 am

Gotta be careful with those. Juan bent two clutch master cylinder shafts using them, as have a lot of people on SRT forums. It is a known problem, but I don't know if they have a fix yet.

Which is sad cause I want it :(

*Edit* The above applies if it's the same part that MPx sells.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

occasional demons
Junior Admin
Posts: 19312
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 22, 2010 1:45 pm

I believe LCR makes their own.

MPX doesn't carry them anymore.

This is what MPX used to sell:

Image

viewtopic.php?t=43234

I can see where you may bend the master cylinder if you adjust it too far, and bottom the slave, before the master, or if the pressure plate has a heavy return force. I can't tell from the MPX pic if the centerline for the shaft is offset from the hole centerline like the stock part. I would like one too, as with the Spec, the plastic pivot flexes pretty good.
Last edited by occasional demons on Mon Nov 22, 2010 8:10 pm, edited 1 time in total.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

User avatar
ltr450r
2GN Member
Posts: 141
Joined: Sat Jan 16, 2010 9:37 pm
Location: Eastern NC

Post by ltr450r » Mon Nov 22, 2010 3:45 pm

well the only other option is what? buy a new factory master cylinder? And Ragetek's is on back order until next year just so yall know. I haven't been able to get up with LCR to see if they have any.

edit: LCR is sold out for a while as well.. Looks like i'll be going back with the factory plastic
-Adrian
Image
2003 SXT, MTX

occasional demons
Junior Admin
Posts: 19312
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 22, 2010 8:09 pm

Yep, you have to either source one from a JY, or buy a new master cylinder. :(
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

SlvrACR
2GN Member
Posts: 4220
Joined: Thu Jun 16, 2005 5:13 pm
Location: Roseville MI

Post by SlvrACR » Mon Nov 22, 2010 10:34 pm

Most people that broke them had AM clutchs and adjusted then wrong. Ive had my MPx one and no problems.
2gn Member Feedback
My Project Log
01 Dodge ACR - SOLD
01 Dodge RT - 279whp 329wtq

Image

occasional demons
Junior Admin
Posts: 19312
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 22, 2010 10:58 pm

Yeah, if it is going to bend the steel rod, it would have snapped the plastic end off anyways. Either way, you are buying a new MC.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

User avatar
ltr450r
2GN Member
Posts: 141
Joined: Sat Jan 16, 2010 9:37 pm
Location: Eastern NC

Post by ltr450r » Mon Nov 22, 2010 11:22 pm

well crap.. i'll hunt around for one in the JY first... Otherwise I'll fork up 120 bucks for a new MC
-Adrian
Image
2003 SXT, MTX

User avatar
Johny
2GN Member
Posts: 1238
Joined: Sat Jun 12, 2010 3:10 pm
Location: Toronto
Contact:

Post by Johny » Sat Jul 20, 2013 10:53 am

Bump.. Anyone know the pn for the little clip that sits inside of that part #5 for the srt?
Image
www.JohnyR.net - Web development

Post Reply

Return to “PN Drivetrain”