Part Number Request: Clutch Master / Slave Cylinder

Post Reply
User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Part Number Request: Clutch Master / Slave Cylinder

Post by nerox » Mon Feb 15, 2010 4:01 pm

for a 2001 R/T ?

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Mon Feb 15, 2010 4:17 pm

I assume this is for your car which is RHD, yes? If so...

The master and slave cylinder are now one unit. However, there is a bracket and screws that they say are needed as well. I have no info on what the bracket is or how many screws you need, but I think it is two.

Clutch Master and Slave, part #4668331AC...MSRP $164.00 USD

Bracket, part #4670237AB...MSRP $22.85 USD

Screws, part #6101614...MSRP $1.45 USD each

The prices I listed will vary greatly over there I'm sure.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Sat Feb 20, 2010 2:25 pm

i have contacted chrysler here in the UK and they say they are seperate units? but they do agree that a bracket and a bolt is needed???
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

occasional demons
Junior Admin
Posts: 20304
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sat Feb 20, 2010 2:43 pm

They most likely have the older stock. Either way, it will work. You can bet it would be the same here. If they had old stock sitting on their shelves, it will be sold, before they order the new design to sell.
Bill
Olha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
2021 Forester

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Sat Feb 20, 2010 4:44 pm

anyone got a picture of the seperate units compared to the all-in-one unit so i can see which one is on my car, i really dont know what they would look like otherwise

occasional demons
Junior Admin
Posts: 20304
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sat Feb 20, 2010 5:48 pm

Image


LHD part, but you get the idea.
Image

Hope this helps.
Bill
Olha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
2021 Forester

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Sun Feb 21, 2010 5:53 am

ok, so thats basically the whole thing except the slave cylinder? them drawings make it look so confusing.

chrysler want about $300 per cylinder and every other shop i contacted give me a diifferent part number or size or spec of the cylinder so nobody seems to really know which one it is!

ahhhh so confusing !!!

occasional demons
Junior Admin
Posts: 20304
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sun Feb 21, 2010 12:49 pm

This should be the PN's for the RHD separate pieces.

Item 10 master 4668330AD $170 US

Item 15 slave 4668331AB $153.00 US

It appears the slave is the same for lhd/rhd. Which would make sense, since at that point they would not need to be different.
www.wermopar.com wrote:International privacy

we r mopar is an indiana corporation headquartered in cedar lake, indiana, usa. We may have site visitors and registrants as well as subscribers and buyers of our products from countries around the world in addition to the United States. If you are located outside of the United States, the personal information you provide to us will be transferred to the United States and governed by applicable U.S. laws and regulations and this Privacy Policy. Some of this information may be transferred to, processed and stored temporarily by our service providers in other countries. By submitting your personal information, you consent to its transfer to and storage in the United States and other countries designated by we r mopar, its governance by U.S. laws and regulations, and its use in accordance with the purposes for which it was originally collected and as set forth in this Privacy Policy.

Shipping Policy
All packages are shipped via FedEx. We never charge a handling fee and our rates are lower than Federal Express listed rates. Orders over 20lbs. will be charged a flat rate per pound. Orders over 500lbs will be shipped as freight collect. Oversize orders that have to go fedex freight/ground will be charged actual shipping.
Does this mean they will ship overseas? IDK, but it might be worth looking into.

www.wermopar.com
1-866-453-2250

Edit:
4668631AD is the domestic pn for the Master cyl.
Bill
Olha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
2021 Forester

User avatar
sidepipe87
2009 Silver Contributor
Posts: 9516
Joined: Fri May 30, 2008 5:35 pm
Location: Pittsburgh, PA
Contact:

Post by sidepipe87 » Mon Oct 28, 2013 12:27 pm

Does anyone know if this is the PN for the entire master/slave/reservoir assembly for a LHD car? If not does anyone have it?

Clutch Master and Slave, part #4668331AC...MSRP $164.00 USD

occasional demons
Junior Admin
Posts: 20304
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Oct 28, 2013 7:49 pm

Danteneon wrote: Clutch Master and Slave, part #4668331AC...MSRP $164.00 USD

Should be, in the above pic, Item 5 is the complete assembled prefilled assy.

They used to sell them separate, but now it is all one assembled unit. Probably too many issues with getting it bled, or the Techs were losing their asses time wise, getting it working properly.

MSRP is now: $185.00

I would call and verify before ordering online, just to be safe.

Edit:

Maybe not I thought I read somewhere they were all one unit now. It may just be the Master and tubing, and you need to buy the slave separately.

This is from the '05 parts:

4668631AD ECB DD5 ACTUATOR, Hydraulic Clutch $209.00

4668331AC ECB DD5 CYLINDER, Clutch Slave, With Tube $185

They do not show it as a superseded number for either, so they may not be sold as one assy. $394 is a hell of a lot of cash for all of it. :/

Almost makes me want to do an ATX swap if mine ever fails. Well, at least give the $$$ to ASP for one of their hydro kits.


SRT
5037340AA EDV DDR CYLINDER, Clutch Master $132

5037339AB EDV DDR CYLINDER, Clutch Slave $185

Interesting the SRT Master is cheaper. I really didn't realize they were different. It seems the pedals are the most referred to thing needed for a swap. Makes one wonder if the SRT master can be used in place of the SE master. :-k

Again, I would call and verify before ordering to be sure they are two individual parts, or a complete assy.
Bill
Olha Koba, a psychologist in Kyiv, said that “anger and hate in this situation is a normal reaction and important to validate.” But it is important to channel it into something useful, she said, such as making incendiary bombs out of empty bottles.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
2021 Forester

User avatar
sidepipe87
2009 Silver Contributor
Posts: 9516
Joined: Fri May 30, 2008 5:35 pm
Location: Pittsburgh, PA
Contact:

Post by sidepipe87 » Tue Oct 29, 2013 7:38 am

The SRT one is wayyy cheaper however the slave cylinder is different so it wouldn't be a direct fit unfortunately. For $300 i had to go the Rock Auto route. Got an entire pre bled assembly for $126 shipped. I didn't want to go aftermarket but i can't justify spending that much for the oem. Thanks for your help Bill!
PM me for your 00+ PCM SKIM/VIN flashing needs. Neon PCMs Plus

Post Reply

Return to “PN Chassis”