Part Number Request: SRT4 front fascia swap parts

Post Reply
Arcticus
n00b
Posts: 3
Joined: Thu Mar 11, 2010 7:19 pm

Part Number Request: SRT4 front fascia swap parts

Post by Arcticus » Tue Nov 16, 2010 3:51 pm

Have a quick question here. I decided to do a front fascia swap on my 05' SXT to the SRT4 front grille and bumper. Got all the parts, the washer bottle, (for fog light clearance), the radiator nozzle things , and of course the front fascia piece itself. I hauled all this down to my body shop man along with the car to get the swap done but have hit a snag. The grille mesh pieces (that fit over what would be the intecooler) dont line up to the bumper. I know i have the correct part numbers for these 5303600AB. Is there srt4 piece I am missing that need to have to install the grille pieces to the bumper? Also will I need o change the front bumper absorber to an srt4 onc to make the facsia fit correctly? If so what are the part numbers for these.

Thanks.. if any of you guys have done this your help would be appreciated. I dont like having my car stuck at a friends shop because of this hitch! :thumbup:

blueneo03
2GN Member
Posts: 1116
Joined: Mon Feb 02, 2009 4:46 pm
Location: Little Rock, AR

Post by blueneo03 » Tue Nov 16, 2010 4:47 pm

it could be u got the one from the srt-d?? idk but i believe the crash bar is the same no worries there..but it should fit no problem you could always just mount the bumper and then put the mesh on later.. so you aren't out of commission
Image

2003 neon se crashed
1998 neon highline Sold
2005 neon sxtSold


"Sorry you are so scared of a possible mechanical problem that you will drive an ugly transportation appliance. I'll keep living a colorful life." -some guy about a camry

occasional demons
Junior Admin
Posts: 19039
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Tue Nov 16, 2010 5:17 pm

4) 5303596AC foam front bumper fascia
The foam is different, but how much, IDk.

9)(not shown) 6035625 SCREW, Grille attaching 12 required

Image
Last edited by occasional demons on Tue Nov 16, 2010 9:57 pm, edited 1 time in total.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

Arcticus
n00b
Posts: 3
Joined: Thu Mar 11, 2010 7:19 pm

Post by Arcticus » Tue Nov 16, 2010 9:40 pm

ty so much, I will try to proceed with this information!!!! :banghead: hate getting stuck during a simple project...

occasional demons
Junior Admin
Posts: 19039
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Tue Nov 16, 2010 9:59 pm

:)

Bump for edit to attaching screw PN. There is almost never a zero at the beginning, if you want it to come up as a valid pn. I forgot to take it off.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

unc-newbie
2GN Member
Posts: 111
Joined: Sun Mar 07, 2010 7:47 pm

Post by unc-newbie » Mon Jan 24, 2011 12:18 am

Where did you get that image from?

Post Reply

Return to “PN Exterior”