Part Number Request: inner door fasteners

srtgtr34 · Post by **srtgtr34** » Wed Jan 07, 2009 2:53 pm

I need the part number for the little white fasteners that hold the inner plastic door peice on.

Post by **occasional demons** » Wed Jan 07, 2009 3:16 pm

Not 100% on this:

6503 167 MSRP $2.40

You could prolly find them at AutoZone

Danteneon · Post by **Danteneon** » Wed Jan 07, 2009 3:38 pm

Those aren't the correct ones. The ones you need are...

Retainer, Trim Panel, Pin/Grommet w/seal...Part #5023351AA...MSRP $8.25 each

The ones you listed are the older style that AutoZone sells. The newer ones the second gens and newer Dodges use are a different style.

srtgtr34 · Post by **srtgtr34** » Wed Jan 07, 2009 8:25 pm

wow, 8.25 each.. dam.
Thanks

BlackRoseRacing · Post by **BlackRoseRacing** » Wed Jan 07, 2009 9:00 pm

srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks

Yup, try selling them to customers over the counter

Post by **occasional demons** » Wed Jan 07, 2009 10:41 pm

Sorry for getting your hopes up. My pirated '01 parts manual does have it's limitations ya know!
Thus why I didn't give it a 100% approval rating.
If you need a nice tool to remove those fasteners with less chance of damaging them: http://tinyurl.com/8ddekc
I have one, or I would be bidding on this myself!

Danteneon · Post by **Danteneon** » Thu Jan 08, 2009 3:12 pm

BlackRoseRacing wrote:
srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks
Yup, try selling them to customers over the counter

No doubt! Or even the $12 ones. "Sorry Mr. customer, those are $12 bucks each. And since you didn't know what you were doing when you removed the panel, you will need 10 of those"

rich tideswell · Post by **rich tideswell** » Thu Jan 08, 2009 7:14 pm

Danteneon wrote:
BlackRoseRacing wrote:
srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks
Yup, try selling them to customers over the counter
No doubt! Or even the $12 ones. "Sorry Mr. customer, those are $12 bucks each. And since you didn't know what you were doing when you removed the panel, you will need 10 of those"

Well Mr. Parts man, I may not know how to properly remove a panel, but even I know when I'm being dry humped over a $0.99 fastener. It's just a Neon, I'll find a another solution] to the problem.

http://www.clipsandfasteners.com/Chrysl ... s_s/66.htm

srtgtr34 · Post by **srtgtr34** » Thu Jan 08, 2009 7:50 pm

They are $18.45 for a pack of 15 which isn't too bad. wow I know where to buy them now, thanks! I broke two when I was installing my speakers, ans that was just the drivers side.

http://www.clipsandfasteners.com/Chrysl ... a19804.htm

Post by **occasional demons** » Thu Jan 08, 2009 11:48 pm

They have an ebay store too, but they don't list those on ebay.

I have never had a problem with those on my door panel. I just get it started and pull it loose by hand the rest of the way. I usually start at the lower corner (latch end), and work my way towards the speaker end.
Prolly just cursed myself.

BlackRoseRacing · Post by **BlackRoseRacing** » Fri Jan 30, 2009 7:01 pm

Great find Rich

nerox · Post by **nerox** » Wed Jul 06, 2011 9:36 am

can someone help me out with the part number for the pins which hold the interior panel to the door?

i've looked on ebay and in parts stores over here but none are the correct type

Thanks!

Post by **occasional demons** » Wed Jul 06, 2011 9:55 am

If there are 8 total for the front door, then this might be the right one. They are not specifically shown in the parts.

5023351AA FASTENER TRIM PANEL MSRP $8.75 each.

These look like the 1gn style. they might work.
http://cgi.ebay.com/CHRYSLER-JEEP-DOOR- ... 2c4a10e37d

But if that is for just one, and not a package, then the mopar ones would be the best bet for the $.

nerox · Post by **nerox** » Wed Jul 06, 2011 1:15 pm

$8.75 each for a little plastic clip ? thats mad!

Post by **occasional demons** » Wed Jul 06, 2011 1:51 pm

Yes it is.

2GN.ORG

Part Number Request: inner door fasteners

Part Number Request: inner door fasteners

Part Number Request : Door Panel Pins