Part Number Request: inner door fasteners

Post Reply
srtgtr34
2GN Member
Posts: 896
Joined: Tue Jul 01, 2008 8:52 am
Location: Cleveland

Part Number Request: inner door fasteners

Post by srtgtr34 » Wed Jan 07, 2009 2:53 pm

I need the part number for the little white fasteners that hold the inner plastic door peice on.

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Wed Jan 07, 2009 3:16 pm

Not 100% on this:

6503 167 MSRP $2.40

You could prolly find them at AutoZone
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Wed Jan 07, 2009 3:38 pm

Those aren't the correct ones. The ones you need are...

Retainer, Trim Panel, Pin/Grommet w/seal...Part #5023351AA...MSRP $8.25 each

The ones you listed are the older style that AutoZone sells. The newer ones the second gens and newer Dodges use are a different style.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

srtgtr34
2GN Member
Posts: 896
Joined: Tue Jul 01, 2008 8:52 am
Location: Cleveland

Post by srtgtr34 » Wed Jan 07, 2009 8:25 pm

wow, 8.25 each.. dam.
Thanks

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12730
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Wed Jan 07, 2009 9:00 pm

srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks
Yup, try selling them to customers over the counter :lol:

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Wed Jan 07, 2009 10:41 pm

Sorry for getting your hopes up. My pirated '01 parts manual does have it's limitations ya know!
Thus why I didn't give it a 100% approval rating.
If you need a nice tool to remove those fasteners with less chance of damaging them: http://tinyurl.com/8ddekc
I have one, or I would be bidding on this myself!
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Thu Jan 08, 2009 3:12 pm

BlackRoseRacing wrote:
srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks
Yup, try selling them to customers over the counter :lol:
No doubt! Or even the $12 ones. "Sorry Mr. customer, those are $12 bucks each. And since you didn't know what you were doing when you removed the panel, you will need 10 of those" :banghead:
If I could just figure out how to meld the Outback and the Neon into one car...

Image

rich tideswell
2GN Member
Posts: 197
Joined: Sun Apr 30, 2006 5:58 pm
Location: MOTOR CITY

Post by rich tideswell » Thu Jan 08, 2009 7:14 pm

Danteneon wrote:
BlackRoseRacing wrote:
srtgtr34 wrote:wow, 8.25 each.. dam.
Thanks
Yup, try selling them to customers over the counter :lol:
No doubt! Or even the $12 ones. "Sorry Mr. customer, those are $12 bucks each. And since you didn't know what you were doing when you removed the panel, you will need 10 of those" :banghead:
Well Mr. Parts man, I may not know how to properly remove a panel, but even I know when I'm being dry humped over a $0.99 fastener. It's just a Neon, I'll find a another solution] to the problem. :tardbang:



http://www.clipsandfasteners.com/Chrysl ... s_s/66.htm
2005 Dodge Neon SRT-4 ACR
PX8 Black, Vipers w/ pass through harness slots in seats, Sunroof, and Kicker Sound

2005 Dodge Neon SRT-4 Commemorative Edition #142
PW1 Stone White w/ PB5 Electric Blue Fang Stripes, Vipers, Sunroof, and Kicker Sound.

srtgtr34
2GN Member
Posts: 896
Joined: Tue Jul 01, 2008 8:52 am
Location: Cleveland

Post by srtgtr34 » Thu Jan 08, 2009 7:50 pm

They are $18.45 for a pack of 15 which isn't too bad. wow I know where to buy them now, thanks! I broke two when I was installing my speakers, ans that was just the drivers side.

http://www.clipsandfasteners.com/Chrysl ... a19804.htm

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Thu Jan 08, 2009 11:48 pm

They have an ebay store too, but they don't list those on ebay.

:-k I have never had a problem with those on my door panel. I just get it started and pull it loose by hand the rest of the way. I usually start at the lower corner (latch end), and work my way towards the speaker end.
Prolly just cursed myself. :shock:
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12730
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Fri Jan 30, 2009 7:01 pm

Great find Rich :thumbup:

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Part Number Request : Door Panel Pins

Post by nerox » Wed Jul 06, 2011 9:36 am

can someone help me out with the part number for the pins which hold the interior panel to the door?

i've looked on ebay and in parts stores over here but none are the correct type

Thanks!

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Wed Jul 06, 2011 9:55 am

If there are 8 total for the front door, then this might be the right one. They are not specifically shown in the parts.

5023351AA FASTENER TRIM PANEL MSRP $8.75 each.

These look like the 1gn style. they might work.
http://cgi.ebay.com/CHRYSLER-JEEP-DOOR- ... 2c4a10e37d

But if that is for just one, and not a package, then the mopar ones would be the best bet for the $.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Wed Jul 06, 2011 1:15 pm

$8.75 each for a little plastic clip ? thats mad!

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Wed Jul 06, 2011 1:51 pm

Yes it is. :lol:
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

Post Reply

Return to “PN Interior”