Part Number Request: 09 Challenger R/T spare tire hold down

Post Reply
User avatar
jmr
2GN Member
Posts: 227
Joined: Thu Feb 01, 2007 11:04 pm
Location: STL, MO

Part Number Request: 09 Challenger R/T spare tire hold down

Post by jmr » Thu Sep 17, 2009 12:34 pm

I need the following part numbers for the 09 Challenger R/T 18" wheel with a 18" spare.

1) spare tire hold down bolt
2) spare tire hold down nut
3) spare tire hold down washer
Image
05 Inferno Red SXT: SRT-Design,MTX,SRT Rear Disc,Mopar VC,K&N Filter
05 Orange Blast SXT: SRT-Design,ATX,SRT Rear Disc,K&N Filter
09 Challenger R/T Deep Water Blue: 24F Pkg, K&N Filter,Mopar Hood Scoop Ducts

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12730
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Sat Sep 19, 2009 5:21 am

Must have gotten one with the air compressor in the trunk Vs a spare :roll:
I ran across this before at work, you have to get parts from a Magnum to convert your car to use a spare....
I'll work on the list for ya later

User avatar
jmr
2GN Member
Posts: 227
Joined: Thu Feb 01, 2007 11:04 pm
Location: STL, MO

Post by jmr » Sat Sep 19, 2009 4:11 pm

It's a base 09 R/T with the compressor and fix a flat sealant. I got a spare and jack from a Charger but need the hold down bolt, nut and washer. Thanks for your help.
Image
05 Inferno Red SXT: SRT-Design,MTX,SRT Rear Disc,Mopar VC,K&N Filter
05 Orange Blast SXT: SRT-Design,ATX,SRT Rear Disc,K&N Filter
09 Challenger R/T Deep Water Blue: 24F Pkg, K&N Filter,Mopar Hood Scoop Ducts

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12730
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Sun Sep 20, 2009 9:41 am

Retention cup - 52059160AC - $10.70msrp
Hold down bolt - 6508110AA - $$14.45msrp
Scissor jack - 4895015AC - $91.80msrp
Jack mounting nut - 6504599 - $5.60msrp
Lug Wrench - 4782999AC - $43.60
Tool Set - 55352852AA - $57.95
Fire Extinguisher - 55352848AA - $0 NS1

User avatar
jmr
2GN Member
Posts: 227
Joined: Thu Feb 01, 2007 11:04 pm
Location: STL, MO

Post by jmr » Sun Sep 20, 2009 8:18 pm

Thank you :rockon:
Image
05 Inferno Red SXT: SRT-Design,MTX,SRT Rear Disc,Mopar VC,K&N Filter
05 Orange Blast SXT: SRT-Design,ATX,SRT Rear Disc,K&N Filter
09 Challenger R/T Deep Water Blue: 24F Pkg, K&N Filter,Mopar Hood Scoop Ducts

occasional demons
Junior Admin
Posts: 20096
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sun Sep 20, 2009 9:01 pm

BlackRoseRacing wrote:Retention cup - 52059160AC - $10.70msrp
Hold down bolt - 6508110AA - $$14.45msrp
Scissor jack - 4895015AC - $91.80msrp
Jack mounting nut - 6504599 - $5.60msrp
Lug Wrench - 4782999AC - $43.60
Tool Set - 55352852AA - $57.95
Fire Extinguisher - 55352848AA - $0 NS1
But, you left out the Spare Tire itself!

Not that I personally see this being a problem, as I have no need for a Challenger spare tire for some time to come.
jmr wrote:It's a base 09 R/T with the compressor and fix a flat sealant.
I guess if you shred the sidewall you're waiting for a tow. I would be doing the same as you.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Sun Sep 20, 2009 9:05 pm

That is insane. I'd do the same, I like having full size spares. Thus having a full size spare and spending tons of time getting a soft tire cover for a 2GN to have a full size spare.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
jmr
2GN Member
Posts: 227
Joined: Thu Feb 01, 2007 11:04 pm
Location: STL, MO

Post by jmr » Mon Sep 21, 2009 12:20 am

I got a 18" 145/80-18 compact spare, jack and lug wrench from a 06 Charger. I needed the small parts to keep it from bouncing around the spare tire well. Stock the Challenger came with a 12V air compressor and Green fix a flat....it didn't give me great confidence.

None of the LX SRT-8's have a compact spare either because of the large Brembo brakes, a spacer is needed in order for it to work.

For 2010 the Challenger SE's and R/T's come with a 18" compact spare as standard. The Chargers,300s and Magnums had them
standard from the beginning..go figure.
Image
05 Inferno Red SXT: SRT-Design,MTX,SRT Rear Disc,Mopar VC,K&N Filter
05 Orange Blast SXT: SRT-Design,ATX,SRT Rear Disc,K&N Filter
09 Challenger R/T Deep Water Blue: 24F Pkg, K&N Filter,Mopar Hood Scoop Ducts

User avatar
BlackRoseRacing
2009 Platinum Contributor
Posts: 12730
Joined: Sat Dec 25, 2004 8:58 am

Post by BlackRoseRacing » Thu Oct 08, 2009 4:44 am

^^^
Correct, 2010 Challengers come with spare's Vs the compressor but as I mentioned before, these components were already used in the Magnum/Charger.....
4782465AA - $105msrp - 18" steel spare
4782819AB - $N/A - 20" steel spare

Post Reply

Return to “PN Interior”