Part Number Request:Sunvisor light bulbs

Post Reply
User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Part Number Request:Sunvisor light bulbs

Post by nerox » Thu Nov 08, 2012 5:52 pm

Does anyone know what type of bulb is used in the sunvisor vanity lights?

One of mine has blown and I've been to 3 different parts stores and none of them recognise it or can find anything vaguely similar.

The only thing I noticed is that it says on it 14v 0.1a but I thought it unusual for a bulb to be rated in amps instead of watts!

Unless they are actually fuses instead of bulbs?
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

occasional demons
Junior Admin
Posts: 19903
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Tue Nov 13, 2012 8:12 am

I think they are # 74? I may be thinking of the lighted rear view mirror tho. But I believe those are 194.


Got any pics of the bulbs?
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Fri Nov 16, 2012 1:53 am

heres a pic ...

Image
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

occasional demons
Junior Admin
Posts: 19903
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 19, 2012 7:29 am

Definitely not a 74 then.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Mon Nov 19, 2012 7:44 am

Nope.
I'm convinced its actually a fuse because its rated at 0.1a

Chrysler dealer has no idea what it is and apparently isn't in the service manual.
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

NickKo
2009 Gold Contributor
Posts: 2248
Joined: Sun Jun 11, 2006 11:24 am
Location: IL./WI.border

Post by NickKo » Mon Nov 19, 2012 8:09 am

nerox wrote:Nope.
I'm convinced its actually a fuse because its rated at 0.1a

Chrysler dealer has no idea what it is and apparently isn't in the service manual.
That pic sure looks like a fuse to me.....

Have you thought about replacing this with an LED bulb ?
In that case, it would be necessary to find out what LED would fit that application..... :-k


- Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm

Official "I'm Going to Drive My Neon till it Dies" Club #000009

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Mon Nov 19, 2012 8:28 am

I did manage to find a festoon type bulb that fitted in the holder, but it was too thick and would scratch the mirror glass underneath
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

occasional demons
Junior Admin
Posts: 19903
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 19, 2012 12:40 pm

Mopar Parts....

VISOR VANITY: 6501966 Bulb MSRP $2.35


Not sure if it is a dealer thing or not, but unless you can find another source...


VANITY LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Lower visor.
(3) Insert a small flat bladed tool between the
lamp lens and lamp.
(4) Carefully pry lens outward.
(5) Remove bulb from socket.
INSTALLATION
(1) Position bulb in socket and snap into place.
(2) Position lens on lamp and snap into place.
(3) Connect the battery negative cable.

Damn, they even cover their butts on disconnecting the battery for that. :lol:
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
nerox
2011 Silver Contributor
Posts: 939
Joined: Sun Dec 20, 2009 10:51 am
Location: United Kingdom

Post by nerox » Mon Nov 19, 2012 12:50 pm

Oh sweet .... Perhaps my local dealer couldn't be bothered to look it up!

Thanks for that!

Perhaps move to P/N requests to help others?
Official "I'm gonna drive my Neon until it dies" Club Member UK#1

Image

occasional demons
Junior Admin
Posts: 19903
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Mon Nov 19, 2012 10:55 pm

The fuse still has me wondering. It is not shown in the schematics. Other than fuse 13 in the PDC, 15 amp.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

Post Reply

Return to “PN Electrical”