How To: Quick Disconnect Battery Cable

Post Reply
Barry McCockener
2GN Member
Posts: 151
Joined: Sun Jul 31, 2011 12:48 pm
Location: Ethiopia, Mongoria

How To: Quick Disconnect Battery Cable

Post by Barry McCockener » Sat Nov 03, 2012 11:19 pm

I got tired of replacing battery terminals because of having to disconnect the battery to change sensors or pretty much anything else electrical, so I got creative and this is what I came up with. Only cost about $15 but it saves a lot of time.

Supplies:
I didn't have any heat wrap so I just used electrical tape. Not pictured is a new brass terminal.

Image

I bought 2 feet of wire which is more than enough but I would've been charged the same amount for 1.5 feet as I did for 2 feet.

I stripped the insulation off a piece of wire about 6" long, doubled over the last 1.5-2" and put it in the fitting that the adapter holds on to and secured it.

Image

I did the same thing with the other piece that screws in except I used the rest of the wire I had.


I screwed all the fitting in, taped over all exposed metal except the QD fitting, and attached the end with the short piece of wire to the battery terminal and spliced the longer portion to the car's negative cable. Had it on for almost 10k miles so far without any issues. I did more taping after I took this pic but you get the idea.
Image

occasional demons
Junior Admin
Posts: 19162
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sun Nov 04, 2012 10:01 am

Eventually, it will give you some headaches. Since there isn't any way to really make a tight connection. Corrosion will set in at the wiring, because it isn't the best of seals.

It is a good concept tho. But unless you have an AGM type battery, and don't live in a humid climate, it will corrode. Both at the wires, and inside the air coupling.

For future reference, all you really need to make disconnect-able, is the wire going to the PDC.

Building wire wouldn't be my choice either. :lol:

But if it works for you, that's what matters.
Bill
dblsg wrote:ya'll a bunch of post whores
epic

2001 Neon ES MTX with '02 R/T PCM
Help support 2GN!

Barry McCockener
2GN Member
Posts: 151
Joined: Sun Jul 31, 2011 12:48 pm
Location: Ethiopia, Mongoria

Post by Barry McCockener » Sun Nov 04, 2012 5:12 pm

Good points. I live in Florida so humidity is always there lol. Eventually I'll use better wire and dielectric grease but that'll be for a lazy day haha

User avatar
dblsg
2GN Veteran
Posts: 10719
Joined: Fri Jun 03, 2005 3:20 am
Location: Aurora, IL
Contact:

Post by dblsg » Mon Nov 05, 2012 10:40 am

Image Sam-I-Am
Image
Official "I'm Going to Drive My Neon till it Dies" Club #000046
Diablo0 wrote: "eh... your opinion doesn't matter... I'm doing what I want..."

freelancer1988
2GN Member
Posts: 103
Joined: Sat Jul 28, 2012 12:20 am
Location: Nashville TN

Post by freelancer1988 » Mon Nov 05, 2012 9:37 pm

I like this better
Image
Image
______________________________________________________________
2002 Dodge Neon SE

racer12306
Junior Admin
Posts: 16012
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Thu Nov 08, 2012 9:19 pm

That looks incredibly unsafe.

There are off the shelf options that cost about the same.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
jmoddes
2GN Member
Posts: 65
Joined: Mon Jun 04, 2012 11:07 am
Location: United States

Post by jmoddes » Fri Nov 09, 2012 4:59 pm

freelancer1988 wrote:I like this better
Image
:withstupid: :thefinger: :tardbang: :tardbang: :rockon: :rockon: :rockon: :rockon: :rockon: :rockon:
-jmoddes (@gmail)
00 Neon
65 Classic

Car\Facebook\My Lights

Hudson_Neon
2GN Member
Posts: 3371
Joined: Wed Mar 14, 2007 4:50 pm

Post by Hudson_Neon » Sat Nov 10, 2012 9:33 am


Post Reply

Return to “HT Electrical”