Exhaust info needed
-
- n00b
- Posts: 12
- Joined: Mon Nov 10, 2014 1:20 pm
- Location: Clyde, Tx
Exhaust info needed
Anybody know anything about this exhaust?
http://www.protuninglab.com/cbe-dn00-so-20l.html
http://www.protuninglab.com/cbe-dn00-so-20l.html
- gtxtreme19
- 2010 Silver Contributor
- Posts: 2061
- Joined: Tue Jan 26, 2010 3:02 pm
- Location: 43554 NW ohio
-
- n00b
- Posts: 12
- Joined: Mon Nov 10, 2014 1:20 pm
- Location: Clyde, Tx
Does your car come with a factory rear sway bar ??
Some folks have said they've had issues with fitment, on Neons with the rear sway bar -- Depending upon the 'kit' (or brand) that was used.
If you don't have a rear sway bar to interfere with fitment -- Then you don't have to worry about that.
Dynomax used to offer an excellent 2.5 exhaust for the Neons which cleared the rear sway bar, no problems.... But it has been discontinued. I don't know if any of the other kits can claim the same.
- Nick
Some folks have said they've had issues with fitment, on Neons with the rear sway bar -- Depending upon the 'kit' (or brand) that was used.
If you don't have a rear sway bar to interfere with fitment -- Then you don't have to worry about that.
Dynomax used to offer an excellent 2.5 exhaust for the Neons which cleared the rear sway bar, no problems.... But it has been discontinued. I don't know if any of the other kits can claim the same.
- Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
You can find that cheaper on ebay.
So many neons so little time.
https://www.youtube.com/user/invujerry/videos
www.instagram.com/invujerry
-
- n00b
- Posts: 12
- Joined: Mon Nov 10, 2014 1:20 pm
- Location: Clyde, Tx
-
- Fresh Fish
- Posts: 1
- Joined: Wed Jan 14, 2015 2:15 pm
- Location: United States
I bought the same exhaust, I had no fitment issues. The only problem is that the tip is absurdly big so i cut it off and welded a 3" rolled tip to make it look more discreet. it sounds really good compared to most of the exhaust clips you hear on youtube, especially with a short ram intake. At 4k it gets loud, like your car has vtec. no noticeable performance increase though
Good to know.MustardTiger250 wrote:I bought the same exhaust, I had no fitment issues. The only problem is that the tip is absurdly big so i cut it off and welded a 3" rolled tip to make it look more discreet. it sounds really good compared to most of the exhaust clips you hear on youtube, especially with a short ram intake. At 4k it gets loud, like your car has vtec. no noticeable performance increase though
Thanks for the review !!
Question:
Does your car, have the rear sway bar ??
- Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-
- n00b
- Posts: 12
- Joined: Mon Nov 10, 2014 1:20 pm
- Location: Clyde, Tx
I wouldn't be surprised, if you had to modify it.3L3K7R0N1X wrote:Sorry for the late response, no net. Will the stock tip mount up right on the body cutout or will i have to modify it? And im honestly not sure about the sway bar, ill have to look at it
If you install the exhaust yourself.... That could give you a bit of flexibility, with how you mount the muffler to match the cutout.
- Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-
- n00b
- Posts: 12
- Joined: Mon Nov 10, 2014 1:20 pm
- Location: Clyde, Tx