Looking at a few things to buy

Have a question that your not sure what category it fits into or isn't really a specific question about a specific part? Ask it here...
Post Reply
Steaks
2GN Member
Posts: 592
Joined: Tue Oct 12, 2004 4:23 pm
Location: Minnetonka, MN

Looking at a few things to buy

Post by Steaks » Mon Dec 06, 2004 4:46 pm

I am looking at buying a lot of stuff so here is a list please help me by saying a good manufactuerer for the parts:

Intake Manifold
Cold Air Intake
Exhaust Manifold
Throttle Body 60mm (I think or 55mm you can help me decide)
Ignition Wires
Ignition Coil

I think that is about it. Please tell me what is a good one to buy.

Please try not to bicker at each other I just need what you guys know do the job well. I have about I think $1200 to spend and I know I might not get EVERYTHING on the list but I will try to get as much as I can. I need Ignition wires and Coil cause I think it might help me with my little miss fire cause I tried replacing the spark plugs and so will try something new.

Thnx.
Last edited by Steaks on Mon Dec 06, 2004 6:08 pm, edited 1 time in total.
Image
Image
Top
Steaks
2GN Member
Posts: 592
Joined: Tue Oct 12, 2004 4:23 pm
Location: Minnetonka, MN

Post by Steaks » Mon Dec 06, 2004 6:07 pm

LOL, I am asking questions about a 1G Neon in a 2g Neon site this is funny.
Image
Image
Top
User avatar
DjTransifi
2GN Member
Posts: 507
Joined: Mon Aug 09, 2004 4:08 pm
Location: ABQ

Post by DjTransifi » Mon Dec 06, 2004 6:49 pm

Speaking of which... Did you get that R/T you were looking for? If so, you should change your banner..
Image
Top
Steaks
2GN Member
Posts: 592
Joined: Tue Oct 12, 2004 4:23 pm
Location: Minnetonka, MN

Post by Steaks » Mon Dec 06, 2004 8:57 pm

I DID! I just don't have a digital camera
Image
Image
Top
User avatar
Louie
Former Jr. Admin
Posts: 1177
Joined: Wed May 12, 2004 12:29 am
Location: Miami, FL
Contact:
Contact Louie

Re: Looking at a few things to buy

Post by Louie » Tue Dec 07, 2004 12:24 pm

Steaks wrote:I am looking at buying a lot of stuff so here is a list please help me by saying a good manufactuerer for the parts:

Intake ManifoldR/T ernie. .theres a group buy on .org
Cold Air Intakeiceman
Exhaust Manifoldr/ternie also can make long tubes, or search .org for a merge fast fab, or a blackdog
Throttle Body 60mm (I think or 55mm you can help me decide)60.. all the dyno's of 60mm tb's show no losses what so ever, only gains. .even on stock cars
Ignition Wirespersonal preference on these. .i run msd and like them
Ignition Coilstock one is fine. .i have an msd, but only because i got a good price on it. .car idles smoother with it

I think that is about it. Please tell me what is a good one to buy.

Please try not to bicker at each other I just need what you guys know do the job well. I have about I think $1200 to spend and I know I might not get EVERYTHING on the list but I will try to get as much as I can. I need Ignition wires and Coil cause I think it might help me with my little miss fire cause I tried replacing the spark plugs and so will try something new.

Thnx.
Image
Top
User avatar
TomZ
2GN Member
Posts: 398
Joined: Sat Jul 03, 2004 7:03 am
Location: Columbus (Blacklick), OH

Re: Looking at a few things to buy

Post by TomZ » Tue Dec 07, 2004 1:33 pm

Steaks wrote: I need Ignition wires and Coil cause I think it might help me with my little miss fire cause I tried replacing the spark plugs and so will try something new.
I've seen posts about the wires on the connector going into the coil being damaged, usually right where the wires bend at the connector base.
Image

'02 Dodge ES, Stone White, MTX, '01 Magnum swap, ACR sways, Tokiko blues, Mopar
2GN lowering springs, Comp 200 cam, PT Cruiser clutch, bolt-ons.
'02 Plymouth ES, Stone White, ATX, free project.
'00 Chrysler LE. ATX (Fiancee's) stock. '02 engine from above car. Mopar springs, Tokiko Blues.
Top
Post Reply

Return to “General 2nd Gen Discussion”