Has anyone installed a Greddy E Manage on 2nd Gen Neon?

chasneonsxt · Post by **chasneonsxt** » Thu Apr 12, 2007 11:15 pm

Pleasae help has anyone installed Greddy E Manage on there 2nd gen neon? If so or know some one who has please point me in the right direction.

I need to know Wiring. Whats needed.

Thank you.

Kevin_GP · Post by **Kevin_GP** » Fri Apr 13, 2007 3:43 pm

I know people have used it, but it would help if what exactly you needed to wire. Like what sensors does it need to be taped into, things like that, then I'm sure we can point you in the right direction.

chasneonsxt · Post by **chasneonsxt** » Sat Apr 14, 2007 12:33 am

I need to know the brown wire from the E Manage says to hook up to a RPM wire. what wire would be the RPM on the neon color code?

Also need to know if you run the injector harness and how to hook it up. One comes with a built in fuel injector from greddy.

How do I hook up the yellow 3 wire harness from e manage Boost to the Srt 4 map sensor?

If anyone knows the factory wires to hook up to please help.

thank you

kc2005ptgt · Post by **kc2005ptgt** » Sat Apr 14, 2007 12:52 am

Isn't there an RPM wire on the coil pack???

Did it come with instructions at all??? Sounds like you need a FSM or a good wiring diagram.

chasneonsxt · Post by **chasneonsxt** » Sun Apr 15, 2007 12:31 pm

I bought it on Ebay the guy said it was new it did not come in the original box and there were no instructions.

heyitsstock · Post by **heyitsstock** » Mon Apr 16, 2007 8:48 pm

^^ bad idea

magnus · Post by **magnus** » Wed Apr 18, 2007 10:48 am

http://www.greddy.com/tech/

I am not sure if you have already checked the tech section over at Greddy. They have the Emanage installation manual up for download.

Also, you need to tap into the center wire comming off the coil pack. I can't remember the color of it, may be orange and green.

chasneonsxt · Post by **chasneonsxt** » Wed Apr 25, 2007 11:05 pm

Ok I have researched for a month both on the Srtforums and neons.org no help with installing this Greddy E Manage. I find a few people who say a few things but thats about it. So If any one can help that would be great.

rannox · Post by **rannox** » Wed Apr 25, 2007 11:43 pm

id say your best bet is downloading that manual.

chasneonsxt · Post by **chasneonsxt** » Wed Jun 06, 2007 12:02 am

I got the e manage installed and working good. Also have the support tool now and a laptop to control the emanage but having problems setting up the Graphs any one have ideas?

I also have the Sohc to Dohc 2.0 srt 4 turbo set up. With the e manage set up. With the e manage support tool. Need help getting started on the graphs.

1.On Parameter settings what is your a/f sensor set at in the 2 boxes? And Injector change what is your cc size before and size after.

2.Air Flow Ajustment map
3.Boost limiter cut setting
4.Anti engine stall seting
5.Additional injector map
6.Acceleration map
7. Ignition timing adjustment map

Every thing is at zeros. New to this program support tool. Car is running with black smoke. This would be very helpful for others to down the road and every one could under stand it better. Please help thank you

lambostealth · Post by **lambostealth** » Tue Jul 10, 2007 2:35 am

1. Should be 14.7 in the first box, and 13.0 in the second, injectors should stay the same unless you changed them.

2. You don't need it.
3. Depends on your motor, if its built, I would say 18psi, if not 10psi.
4. leave it.
5. unless you added extra injectors, you don't need this.
6. I belive that needs a base map from greddy
7. should be pulling 12* by redline gradually.

You can go to SRTforums, PM turbotrix2004, he has had experience with the Emanage......or contact Jay, at N2MB racing in the vendor section of SRTforums.

Good luck

daaboots · Post by **daaboots** » Mon Aug 27, 2007 1:04 pm

This should help http://forums.neons.org/viewtopic.php?t=282379