front wireing for door speakers
front wireing for door speakers
hello all i would like to know if some one could help me run wires to my front speakers ?
i cant use my factory wires thanks
i cant use my factory wires thanks
Re: front wireing for door speakers
I was just thinking the same thing ..... Why can't you run the factory wires ??rud3boi wrote: i cant use my factory wires thanks
-Nick
-1998 2-dr SOHC MTX= 57mm TB; Maddog STS
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
-2000 Ply.LX w/MTX = Maddog STS; CAI; 2.5 exh.; 60mm T/B
-2001 ATX w/Syked PCM + Magnum header
-2001 ACR w/SRT T/B bored out to 55mm
Official "I'm Going to Drive My Neon till it Dies" Club #000009
just rip your door apart to get at the speaker
run th wires from the radio up under the dash somewhere and then run them through the plastic piece between the door jamb .. youll have to be creative with that since its a solid piece that all the wiring plugs into on one side then out the other side..
depending if you have any power options or not the only thing plugged in there might be the door speakers.. which was the case for me since i got no power options.. so i just cut out a big ass hole in the plastic piece to run my power door lock cables through
in the case of speaker wires a nice speedy drill bit would do just fine
run th wires from the radio up under the dash somewhere and then run them through the plastic piece between the door jamb .. youll have to be creative with that since its a solid piece that all the wiring plugs into on one side then out the other side..
depending if you have any power options or not the only thing plugged in there might be the door speakers.. which was the case for me since i got no power options.. so i just cut out a big ass hole in the plastic piece to run my power door lock cables through
in the case of speaker wires a nice speedy drill bit would do just fine
problem is i hard mounting the tv in my dash no access to the wireing behind the screen.
i didnt occur to me to try the wireing harness out imma try again tommeow to see if its just not my amp but it doesnt seem like signal is getting to those speakers i hope that it works so it will save me a bunch of time.
i got some great pioneers 4 ways
they sound assume (so ive heard i gatta get two speaker baffels tommeorow so i my bass doesnt mix with my 6x9 s
Pioneer TS-A1682R - 6-1/2" 4-Way 220 i think 40 rms or 60 i gatta check
Pioneer TS-A6982R - 6x9" 440W 4 way 80 rns
i didnt occur to me to try the wireing harness out imma try again tommeow to see if its just not my amp but it doesnt seem like signal is getting to those speakers i hope that it works so it will save me a bunch of time.
i got some great pioneers 4 ways
they sound assume (so ive heard i gatta get two speaker baffels tommeorow so i my bass doesnt mix with my 6x9 s
Pioneer TS-A1682R - 6-1/2" 4-Way 220 i think 40 rms or 60 i gatta check
Pioneer TS-A6982R - 6x9" 440W 4 way 80 rns
-
onewickedkid05
- 2GN Member
- Posts: 661
- Joined: Tue Jun 19, 2007 10:27 pm
- Location: West Lawn PA
- Contact:
again, where are you running them from? Where is the head unit, or are you using the computer? If the computer, and the output from the comp is in the glove box like the components in your pics, you should be able to run them from the speaker thru the door jamb, and thru the bottom of the dash, behind the computer, and into the glove box from the back.
-
onewickedkid05
- 2GN Member
- Posts: 661
- Joined: Tue Jun 19, 2007 10:27 pm
- Location: West Lawn PA
- Contact:
Just cut a tiny hole in the carpet to feed the wires thru from the amp. under the door sill and through the plastic shit in the door jamb with the rest of the wires to the speaker and.... DA-DA-DA-DAA!! Your connected. i wanan kno how you hooked up a tv in your dash but cant run a couple wires. im not talkin shit just a question.
-J.J. | Official I sold my Neon Member #008
86.5 Nissan Hardbody LB- will be for sale soon...
1989 Yota PU- "Tammy" -Rest In Pieces...
2000 Plym Neon- "Stacy" -Sold 3/25/09 =(
86.5 Nissan Hardbody LB- will be for sale soon...
1989 Yota PU- "Tammy" -Rest In Pieces...
2000 Plym Neon- "Stacy" -Sold 3/25/09 =(
Ntyvirus1 wrote:im debadged so i just drive a gray thing.
[/u]