turbo adapter plate needed for neon acr!!!

nateneon · Post by **nateneon** » Thu Jun 05, 2008 9:33 pm

2002 dodge neon acr needs an adapter plate to install srt4 manifold/turbo!!! anyone know where i can get one and how much they are??

Post by **occasional demons** » Thu Jun 05, 2008 9:38 pm

They are no longer made. Dante will show you a pretty pic of his tho!
unless you get extremely lucky, and someone sells theirs, or starts making them again, you will have a hard time obtaining one.

Danteneon · Post by **Danteneon** » Thu Jun 05, 2008 9:42 pm

Of course! Always happy to oblige!

Actually, this is the second time I showed him this, but I couldn't resist

Like I said in your previous post looking for one, they are rarer than hell right now

southga00 · Post by **southga00** » Thu Jun 05, 2008 9:55 pm

since they are no longer made is there anyway someone could post the dimensions holes sizes and spacing? It is made of 1 inch aluminum correct. I am able to make one i just need the spacing of the bolt holes and exhaust holes also bolt sizes, then i could probably make my own. im sure a lot of us would appreciate it.

Danteneon · Post by **Danteneon** » Thu Jun 05, 2008 10:06 pm

I am in the process of getting those dimensions. I will have a post about this once I finish

LionheartedSXT · Post by **LionheartedSXT** » Sat Jun 07, 2008 4:20 pm

contact mattdog, because he told me that he will be making a couple more for the summer and i think its really the end after that, he already has a couple people on the waiting list including myself...

southga00 · Post by **southga00** » Sat Jun 07, 2008 5:15 pm

so how much are the adapter plates going for?

ZeroChad · Post by **ZeroChad** » Sat Jun 07, 2008 5:18 pm

You could always try one of these flanges, then port it slightly to match the magnum exhaust ports.

LINK
I think they're around $80

LionheartedSXT · Post by **LionheartedSXT** » Sat Jun 07, 2008 5:25 pm

southga00 wrote:so how much are the adapter plates going for?

he said $220 shipped

GreeNeons03 · Post by **GreeNeons03** » Wed Jun 11, 2008 9:02 am

LionheartedSXT wrote:contact mattdog, because he told me that he will be making a couple more for the summer and i think its really the end after that, he already has a couple people on the waiting list including myself...

How can I get on said waiting list?

2k1MotorSport · Post by **2k1MotorSport** » Wed Jun 11, 2008 9:31 am

So this would bolt up to my magnum motor? Or are all the adapters the same?

LionheartedSXT · Post by **LionheartedSXT** » Wed Jun 11, 2008 10:23 am

2k1MotorSport wrote:So this would bolt up to my magnum motor? Or are all the adapters the same?

Yes it would bolt up to your motor, and No the adapters are not all the same, he makes two, one for the magnum to srt and the standard sohc to srt...

2k1MotorSport · Post by **2k1MotorSport** » Wed Jun 11, 2008 11:35 am

got ya.. nice to know.

southga00 · Post by **southga00** » Thu Jun 12, 2008 7:36 pm

so has anyone got the dimensions to this adapter plate yet.

Post by **occasional demons** » Thu Jun 12, 2008 11:27 pm

southga00 wrote:so has anyone got the dimensions to this adapter plate yet.

Danteneon wrote:I am in the process of getting those dimensions. I will have a post about this once I finish

Patience Grasshopper!

Danteneon · Post by **Danteneon** » Fri Jun 13, 2008 5:46 pm

I have all the info!

But I have tried twice to post it at work, and both times I lost all the info before I could post it

(different reasons each time)

I will get this posted as soon as I get an hour of down time at the house...

ZeroChad · Post by **ZeroChad** » Fri Jun 13, 2008 6:59 pm

Thats gotta be a close cousin of copyright infringement lol. Hell, I'm all for it though, I'm gunna need one.

Someone should try porting one from that link above though.

Danteneon · Post by **Danteneon** » Sat Jun 14, 2008 12:35 pm

Specs are up!

Here be teh link...

http://forum.2gn.org/viewtopic.php?t=32908&highlight=

BIGSRTURBO · Post by **BIGSRTURBO** » Sat Jun 14, 2008 7:02 pm

awsome...

srtminime · Post by **srtminime** » Mon Jun 16, 2008 6:48 pm

OR you can always "adapt" the PT Cruiser 2.4 into there and not only get boost, but extra Torque to boot. If an SRT4 can do it, so can you...

gilly02le · Post by **gilly02le** » Sat Jun 21, 2008 9:48 am

Always makes me wonder why no-one swaps in pt-gt engines. seems to me i've never even seen one driven hard. Would make a much better swap engine, No?

Post by **racer12306** » Sat Jun 21, 2008 2:43 pm

You would have to get a new intake manifold for it.

srtminime · Post by **srtminime** » Mon Jun 23, 2008 3:43 pm

Yeah, the intake is different, but I see SRT intake manifolds for sale on srtforums for around $75-100 all the time. I bought one with a broken TB flange for $40 so I can get a custom one made up. If you want to boost you might as well make it as efficient as possible...