SRT Wheels on a SXT?

Anything that has to do with wheels and tires goes here. Will a wheel fit? Ask it here. Will a tire fit your wheel? Ask it here.
DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

SRT Wheels on a SXT?

Post by DuhNeon179 » Sat Jul 12, 2008 10:32 pm

Can you put a SRT 17" wheel on a SXT Neon with drum brakes in the back? If not what do I need to change?

IowaNeon04
2GN Member
Posts: 144
Joined: Tue Jul 08, 2008 9:55 pm
Location: You have 3 guesses...

Post by IowaNeon04 » Sat Jul 12, 2008 11:11 pm

They will bolt right up no problem... just don't leave the stock SRT4 tire on there... they are bigger than what you can fit on an SE/SXT... I would shoot for a 205/40/17 or close size to that or you'll have clearance issues.
Image

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sat Jul 12, 2008 11:23 pm

The guy I was going to buy it from today, said that I might have to change the Strut is that true? If not it would bolt right on no problem? He also said that it will come close in the front but he isnt quite sure about teh back.

IowaNeon04
2GN Member
Posts: 144
Joined: Tue Jul 08, 2008 9:55 pm
Location: You have 3 guesses...

Post by IowaNeon04 » Sat Jul 12, 2008 11:25 pm

Hmm, well I didn't think there was that much of an offset problem with them. I was always under the impression that SRT4 tire size was the issue when you tried putting them on an SXT... not the rim. Somebody else please chime in here if I am wrong.
Image

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Sat Jul 12, 2008 11:33 pm

You do not need to change anything at all, it will bolt up perfectly, as long as you do not use the stock sized tires as was mentioned in the first reply.

The stock SRT tires at 50 series which are too tall. Go with a 40 series and you'll be just fine, no spacers, or any other crap like that.

Buy them without the tires and put on a 40 series, they look good, and you will like them.
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sat Jul 12, 2008 11:37 pm

Excellent. I have to get new tires anyways the other ones all 4 of them look like there going to blow out. At Carlisle today I bough M12 x 1.5 wheel lock hope I did not screw anything up, is that the right size? I looked at all of the Neon's asked around people were not quite sure.

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Sat Jul 12, 2008 11:38 pm

I have no clue what that is...
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

IowaNeon04
2GN Member
Posts: 144
Joined: Tue Jul 08, 2008 9:55 pm
Location: You have 3 guesses...

Post by IowaNeon04 » Sat Jul 12, 2008 11:42 pm

Yes, you bought the right size (M12 x 1.5 is the bolt and thread pattern on the lug).
Last edited by IowaNeon04 on Sat Jul 12, 2008 11:43 pm, edited 1 time in total.
Image

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sat Jul 12, 2008 11:43 pm

Phew, thought it was a waste of money. Thanks guys! :D appericate the help!

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Sat Jul 12, 2008 11:43 pm

Oh a wheel lock, OK... I got confused with misspellings and convoluted sentences, lol!
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sat Jul 12, 2008 11:49 pm

:thumbright: Thank's alot guys :D

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Sat Jul 12, 2008 11:50 pm

It's what we're here for! Now introduce yourself and post pics of your car! :lol:
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

User avatar
b1llyw
2GN Member
Posts: 198
Joined: Wed Apr 11, 2007 3:25 pm
Location: Connecticut
Contact:

Post by b1llyw » Sun Jul 13, 2008 6:31 am

What about the SRT-4 ACR BBS rims? Can you run that stock tire on an SXT? I think it is a 225-45-16 that comes on them.
2005 SXT, MTX

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Sun Jul 13, 2008 12:22 pm

I think so. I'm running a 16" wheel with a 215/50/16, so you *should* be OK, but don't quote me on that one, haha.
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Sun Jul 13, 2008 8:19 pm

i answered on the org, but i'll post here for the 2gn people.

i believe the srt acr perch is the same height as the sxt/rt perch. so that wheel/tire combo should fit no problem. 225/45/16 is only a hair taller than stock too.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sun Jul 13, 2008 9:04 pm

So keep the 17" mags and go with the 40 series tires?

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Sun Jul 13, 2008 9:26 pm

basically, but be advised. technically the 205/40 does not fit on a 6" wide wheel (such as the SRT wheel). but many people have put them on. the minimum rim width for that size tire is 7". personally i wouldn't run 205/40 on a 6" wheel. but thats just me
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

DuhNeon179
2GN Member
Posts: 155
Joined: Sat Jul 12, 2008 9:56 pm

Post by DuhNeon179 » Sun Jul 13, 2008 9:27 pm

Your best suggestion for this?

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Sun Jul 13, 2008 9:30 pm

to either change the struts to srt struts and run the 205/50 tire and deal with the car being slower and the speedo being off.

or

get properly sized wheels

but that is just me. many people have put 205/40 on the srt wheel and haven't had a problem. i just like things to be right.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
srt4evah
2GN Member
Posts: 153
Joined: Mon Oct 09, 2006 1:49 pm
Location: Austin, TX

Post by srt4evah » Thu Jul 17, 2008 11:57 am

racer12306 wrote:basically, but be advised. technically the 205/40 does not fit on a 6" wide wheel (such as the SRT wheel). but many people have put them on. the minimum rim width for that size tire is 7". personally i wouldn't run 205/40 on a 6" wheel. but thats just me
Uhm, why would changing the sidewall height affect whether or not the tire would fit on a 6" wide rim? The tire width of 205mm is the same on both the stock SRT-4 tire and the propose 205/40...
2010 Mitsubishi Evolution X MR (380whp/376wtq)
2005 Dodge SRT-4 (445whp/475wtq)

User avatar
SYRYS04
2GN Member
Posts: 69
Joined: Mon May 05, 2008 5:20 am
Location: WHERE IM AT
Contact:

Post by SYRYS04 » Mon Aug 18, 2008 9:39 am

Maybe he meant don't put a 205 on a 6" wheel. instead use a 195.. I don't know..

All I know is the rim fits on a sxt but get a tire that fits that wheel that's not taller than a 40.

Jus what I think. I'm not a pro or anything.
THE TRUTH HURTS
LOVE IS PAIN
SO REGARDLESS OF WHAT I'M DOIN
I'M BREAKIN YOUR HEART

-SYRYS-

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Mon Aug 18, 2008 11:01 am

The problem with running a 205 section width on a 40 aspect ratio is that the sidewall is too short for the tire to fit "properly". With a taller sidewall the tire is allowed to flex inward more to fit on a 6" wide wheel. A 45 ratio or taller is needed to fit correctly. Thats why the SRT runs a 50.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Tue Aug 19, 2008 3:33 pm

If you look at a tires specs one of the categories is recommended rim width. This will be a range.

and now that I read Dante's post, he hit the nail on the head.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
Lizbeth
2GN Member
Posts: 199
Joined: Wed Jul 16, 2008 9:20 pm
Location: Oklahoma City OK..

Post by Lizbeth » Wed Aug 20, 2008 7:55 pm

TheRandom1 wrote:You do not need to change anything at all, it will bolt up perfectly, as long as you do not use the stock sized tires as was mentioned in the first reply.

The stock SRT tires at 50 series which are too tall. Go with a 40 series and you'll be just fine, no spacers, or any other crap like that.

Buy them without the tires and put on a 40 series, they look good, and you will like them.




you dont need to get the 40 series tires i have mine with 205/50/17 Image
~I don't drive fast I fly low~
Image
official "Im Going To Drive My Neon Till It Dies" Club #97

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Wed Aug 20, 2008 8:18 pm

what kind of struts do you have?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
Lizbeth
2GN Member
Posts: 199
Joined: Wed Jul 16, 2008 9:20 pm
Location: Oklahoma City OK..

Post by Lizbeth » Wed Aug 20, 2008 8:38 pm

STOCK STURTS
~I don't drive fast I fly low~
Image
official "Im Going To Drive My Neon Till It Dies" Club #97

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Wed Aug 20, 2008 8:40 pm

how is it not rubbing?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
Lizbeth
2GN Member
Posts: 199
Joined: Wed Jul 16, 2008 9:20 pm
Location: Oklahoma City OK..

Post by Lizbeth » Wed Aug 20, 2008 8:49 pm

u gotta know how to do it there's a little trick to it
~I don't drive fast I fly low~
Image
official "Im Going To Drive My Neon Till It Dies" Club #97

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Wed Aug 20, 2008 8:51 pm

then you should share it. is it wheel spacers?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
TheRandom1
2GN Veteran
Posts: 9938
Joined: Mon Jan 02, 2006 11:17 pm
Location: Chicagoland

Post by TheRandom1 » Wed Aug 20, 2008 8:52 pm

Or a hammer on the spring perch.
Image
Danteneon wrote:You doing this swap with your tech level is like asking a squirrel to land a 747.

Post Reply

Return to “Wheels / Tires”