(_SxXxT_) 7/15/13. The car runs
Thanks.... It won't be a competition sounding box but that's fine with me... As long as there is no rattle and it has good quality bass I'll b happy... It's only a 10 so it should b exactly what I was lookin for... This thing is best of both worlds... I have storage, I have little bump and if I need to use the trunk as a trunk I can...
it was list early christmas for me today... thanks to caraudiohalic(mike)

Plate light, x10 white led/s and trunk light

Ported and powdercoated black Srt with less then 100 miles on the sensors TB:
I think im gonna sell it.



wrinkle black radiator cover

got my door inserts so i can wrap them in these covers i made... same leather that i wrapped my b pilliar in and with a double stitch down the center....

plate light installed yay.. good bye 1 single led plate light

painted the trunk frame semi gloss black. to seal it from mostiure and so it doesnt look like poop bak there.

and started to paint the under side of the cover board... its finished now.

next is the trunk led i hooked up.. it came with two so the second one is gonna go under the cover board so i can see when i lift it up...

i also painted the grill inserts i just go but didnt get a pic..
still to do...
fiberglass inside of sub box..
sand sub box.
wrap sub box..
bolt sub box to car frame..
run sub wires...
finish painting wood frame and cover board
wire light to bottom of the cover board..
i also picked up some tires for the 16's that im gonna get put on the car tomorrow.

Plate light, x10 white led/s and trunk light

Ported and powdercoated black Srt with less then 100 miles on the sensors TB:
I think im gonna sell it.



wrinkle black radiator cover

got my door inserts so i can wrap them in these covers i made... same leather that i wrapped my b pilliar in and with a double stitch down the center....

plate light installed yay.. good bye 1 single led plate light

painted the trunk frame semi gloss black. to seal it from mostiure and so it doesnt look like poop bak there.

and started to paint the under side of the cover board... its finished now.

next is the trunk led i hooked up.. it came with two so the second one is gonna go under the cover board so i can see when i lift it up...

i also painted the grill inserts i just go but didnt get a pic..
still to do...
fiberglass inside of sub box..
sand sub box.
wrap sub box..
bolt sub box to car frame..
run sub wires...
finish painting wood frame and cover board
wire light to bottom of the cover board..
i also picked up some tires for the 16's that im gonna get put on the car tomorrow.
-
2low4uneon
- 2GN Member
- Posts: 355
- Joined: Mon Jun 08, 2009 6:22 pm
- Location: Green Bay, WI
Out of curiosity how does the system sound. You lose about 3db going sealed ( I prefer sealed for a daily system ) , another 1-2 DB using fiberglass. Neons inherrently sound best ( loudest ) with a sub fired towards trunk ( it helps with the resonant frequency and distance to cabin and has to do with the "wave" ) not to mention blocking the escape path ( back seat ) will cut it down a bit to.
I know your goal is obviously not SPL but a single 12" needs all the help it can get and although it certainly looks very nice judging from experience people outside are going to hear more than you will in cabin.
For reference for those not keen on audio and think eh whats a few DB. If your car hits say 140db ( very respectable for a everyday system ) a upgrade that nets you 143DB is actually and sounds twice as loud and vice versa 137db would be half as loud.
I know your goal is obviously not SPL but a single 12" needs all the help it can get and although it certainly looks very nice judging from experience people outside are going to hear more than you will in cabin.
For reference for those not keen on audio and think eh whats a few DB. If your car hits say 140db ( very respectable for a everyday system ) a upgrade that nets you 143DB is actually and sounds twice as loud and vice versa 137db would be half as loud.
-
Hudson_Neon
- 2GN Member
- Posts: 3371
- Joined: Wed Mar 14, 2007 4:50 pm
True but a sealed box custom fiberglassed into the back part of spare tire well angled just slightly up should net you good response and about a 6db increase with about a 3/4 wave, place the amp on the sides in the rear and you also get way less trunk rattle and it still looks clean.Hudson_Neon wrote:chew, i think the goal was to have a clean looking system with trunk space while having a little bass at the same time. the problem with sums is that they take up valuable trunk space generally
Just a friendly suggestion to get the most "bang" out of an investment.
- RobsProjectSOHC
- 2012 Gold Contributor
- Posts: 415
- Joined: Fri Aug 19, 2011 11:36 am
- Location: NY
Can i steal your idea with your trunk? I think thats awesome....i need a place to store the toolbox and such.
Project 003. Just building a Daily Driver with some upgrades.
For Sale Thread | CarDomain | FeedBack
Official "I'm gonna drive my Neon until it dies Club" Member #119
For Sale Thread | CarDomain | FeedBack
Official "I'm gonna drive my Neon until it dies Club" Member #119
-
Silver-Shadow
- 2GN Member
- Posts: 156
- Joined: Sun Dec 18, 2011 12:57 am
- Location: Southern California
That strut bar is nice, how did you get the measurements? I don't think there is a "stock" one, did you have to fabricate it?

PS2 SXT - New baby
08 530i e60 M5 Kit - Sold
E39 M5 - BlueMajik (Safely tucked away in the garage)
E39 528i - Sold at 167k miles
Yellow '77 Plymouth Volare (RIP)
skypeme: dtvarnum
Official "I'm Going to Drive My Neon till it Dies" Club #?
-
Hudson_Neon
- 2GN Member
- Posts: 3371
- Joined: Wed Mar 14, 2007 4:50 pm
you can buy them... or fab them. i fabbed mine. but if you're not good with that stuff, go to modern's website.Silver-Shadow wrote:That strut bar is nice, how did you get the measurements? I don't think there is a "stock" one, did you have to fabricate it?
back on topic, i'm loving your car man. this thing is so clean. makes me want to redo my trunk
Thanks everyone..... First off the sub sounds perfect!!!!!!!! No trunk rattle and it sounds exactly like I wanted to...
Picture this... When U watch a movie at ur house u want a really good surround sound. (Home theater) well that's the whole idea for the sub... I want bass when it's needed... I hate when u can hear a car 5 miles away and when it drives by all I here is trunk rattle... I spent bout an hour tunning the new 6x9's Nd subs to balance perfectly... I'm getting new 6.5's soon to complete my surround sound car system lol.
This is a fiberglass sub but with mdf base and several layers of fiberglass. It's sealed except the hole for wires and two small holes just to let it breath. The sub is a 900 watt nd the amp is 2500 watt
This idea is open for tweaking or stealing... This was the best of both worlds... Storage space and little bass...
Picture this... When U watch a movie at ur house u want a really good surround sound. (Home theater) well that's the whole idea for the sub... I want bass when it's needed... I hate when u can hear a car 5 miles away and when it drives by all I here is trunk rattle... I spent bout an hour tunning the new 6x9's Nd subs to balance perfectly... I'm getting new 6.5's soon to complete my surround sound car system lol.
This is a fiberglass sub but with mdf base and several layers of fiberglass. It's sealed except the hole for wires and two small holes just to let it breath. The sub is a 900 watt nd the amp is 2500 watt
This idea is open for tweaking or stealing... This was the best of both worlds... Storage space and little bass...
love the wrapped door pieces. They came out very nice. not quite diggin the sub box wrapped in leather. Think it looked a lot better in the trunk carpet.
- Custom or Nuthin -
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
So it's been too long... Since iv made an update.
First off I ordered an installed my maddogg 80% sts

Next is my mpx chrome shift knob

Side note maddogg = perfection
Next is my solid motor and tranny mounts.

Top motor mount installed

I bought a Udp and odp
And new belts and I'm going to try and install all the mounts and pulleys and belts..
Also what do u peeps think about this

First off I ordered an installed my maddogg 80% sts

Next is my mpx chrome shift knob

Side note maddogg = perfection
Next is my solid motor and tranny mounts.

Top motor mount installed

I bought a Udp and odp
And new belts and I'm going to try and install all the mounts and pulleys and belts..
Also what do u peeps think about this

-
2low4uneon
- 2GN Member
- Posts: 355
- Joined: Mon Jun 08, 2009 6:22 pm
- Location: Green Bay, WI
thanks u 2 lol
got some quick updates and stuff that i need to sell cuz i just bought more crap lol
heres what i started with this morning

(-heres the stuff i need to sell-)
(-obx sts with chrome thread ball (55 shipped whole assembly-)
(-modernperformance short end links unused (20 shipped)
(-shaved top motor mount with painted over modern poly bushings installed... just painted over the bushings does not effect performance ( i would like to sell botht he top and bottum together with inserts for 60 bucks) ill also be willing to get them powdercoated any color. iv got a hook up on powdercoating..
so 100 for top and bottom with inserts and powdercoated almost anycolor..

and the massive brand srt tranny mount

i thought i could use it cuz the holes where so close but just no go so i ordered a new tranny mount and modern tranny mount inscerts
oh and heres a lil side project that im workin on for a member aka 2lowforuneon



plastic welding so its not all fiberglass and bondo heres about a third finished

got some quick updates and stuff that i need to sell cuz i just bought more crap lol
heres what i started with this morning

(-heres the stuff i need to sell-)
(-obx sts with chrome thread ball (55 shipped whole assembly-)
(-modernperformance short end links unused (20 shipped)
(-shaved top motor mount with painted over modern poly bushings installed... just painted over the bushings does not effect performance ( i would like to sell botht he top and bottum together with inserts for 60 bucks) ill also be willing to get them powdercoated any color. iv got a hook up on powdercoating..
so 100 for top and bottom with inserts and powdercoated almost anycolor..

and the massive brand srt tranny mount

i thought i could use it cuz the holes where so close but just no go so i ordered a new tranny mount and modern tranny mount inscerts
oh and heres a lil side project that im workin on for a member aka 2lowforuneon



plastic welding so its not all fiberglass and bondo heres about a third finished

-
2low4uneon
- 2GN Member
- Posts: 355
- Joined: Mon Jun 08, 2009 6:22 pm
- Location: Green Bay, WI
So the pictures don't show a lot of progress but I got two days worth of progress... Some seen and sum unseen.
First off I got the 1st get modern pully installed
2nd got the ODP installed
3rd got the solid bottom mount installed
4th all new belts
5th changed cabin filter
6th fixed 0gauge wire issue
7th removed seatbelt harness bar 4 CARSEAT!
(baby due march 13th)
8th swept interior
9th fixed seat belt issues
10th ordered new amp
11th ordered new transmission mount and modern solid transmission mount inserts and new plugs and wires also from modern 132 mpx bill
----(yay work bonuses)
12th properly mounted mpx shifter ball..
13th filled air up in driver side tires didn't do other side cuz air compressor issues..
When I recieve new tranny mount I'll be installing it cuz my tranny mount is over 10 years old and is GONE!
I'd anyone has questions about any of the stuff I just installed feel free to ask cuz some was a pain in the rump.



First off I got the 1st get modern pully installed
2nd got the ODP installed
3rd got the solid bottom mount installed
4th all new belts
5th changed cabin filter
6th fixed 0gauge wire issue
7th removed seatbelt harness bar 4 CARSEAT!
(baby due march 13th)
8th swept interior
9th fixed seat belt issues
10th ordered new amp
11th ordered new transmission mount and modern solid transmission mount inserts and new plugs and wires also from modern 132 mpx bill
12th properly mounted mpx shifter ball..
13th filled air up in driver side tires didn't do other side cuz air compressor issues..
When I recieve new tranny mount I'll be installing it cuz my tranny mount is over 10 years old and is GONE!
I'd anyone has questions about any of the stuff I just installed feel free to ask cuz some was a pain in the rump.



- Alex Kurdian
- 2GN Member
- Posts: 1023
- Joined: Mon Jul 23, 2007 2:14 am
- Location: Australia
-
Caraudioholic24
- 2GN Member
- Posts: 4135
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
are you looking to sell the srt tranz mount?
- Custom or Nuthin -
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-My SRT4 swap project log-
viewtopic.php?p=923967#923967
-My 2nd gen progress log-
viewtopic.php?t=52665&highlight=
-My 1st gen project log-
http://forums.neons.org/viewtopic.php?f ... 7#p3090897
-
Caraudioholic24
- 2GN Member
- Posts: 4135
- Joined: Sat Mar 22, 2008 1:56 am
- Location: Cumberland R.I.
Congrats!
Justin
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823
[02 R/T sold][00 Highline sold][04 r/t scrapped][95 NYG Sport coupe][01 r/t DD]
http://www.cardomain.com/ride/2931823


















