So like i said before i just recently picked up a turbo kit from my buddy and he claimed ti was a SOHC mani but it turned out to be DOHC WTF!
It was still a good buy for 200 (turbo, mani, intercooler,all da pipes and lines for it) but i dont think the mani will bolt up....... any suggestions of what i should do? is it a possiblitly to drill new holes in the mani or is that no possible? pleaseee help, this is the only thing left i need and then i can get goin on the install. Ill make sure to take lots of pics and do a write up once i get past this small problem
duel cam wtf
-
racer12306
- Junior Admin
- Posts: 16015
- Joined: Sun Oct 24, 2004 8:53 pm
- Location: Baltimore, MD
- Contact:
keep an eye out for one of the few adapters that are available used. iirc the 2.4 DOHC and the 2.0 DOHC have the same bolt pattern, so any one of the adapters should work.
or
buy a new manifold. you don't want to drill into cast iron, and it won't seal up well.
or
buy a new manifold. you don't want to drill into cast iron, and it won't seal up well.
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!
-
Cbussilver01es
- 2GN Member
- Posts: 837
- Joined: Tue Jan 30, 2007 1:03 am
- Location: New Albany, OH
Or maybe if someone I know Would list all that was involved with swapping over to a DOHC head 
you could try that, 
All that aside, like frank said you could try buying a new manifold.
you could try that, All that aside, like frank said you could try buying a new manifold.
-Sean
01 Dodge Neon MSII 2.0 DOHC turbo, '13 Dodge Dart Mopar Edition 1.4 Multi-Air turbo
Nos is a lot like a hot chick with std's you wanna hit it but are afraid of the consequences.
http://www.cardomain.com/ride/2311033
01 Dodge Neon MSII 2.0 DOHC turbo, '13 Dodge Dart Mopar Edition 1.4 Multi-Air turbo
Nos is a lot like a hot chick with std's you wanna hit it but are afraid of the consequences.
http://www.cardomain.com/ride/2311033
Have someone make a custom tubular manifold for you. Log style. Its fairly cheap to make. Materials should not go for more than 100 bucks with another 50 to 60 for labor to weld it up.
2003 Silver SXT - Totalled
2005 Silver Subaru Legacy 2.5GT Turbo -Daily
1990 White SR powered 240sx - My sliding slut.
I miss my neon at times. She treated me well and taught me a lot about cars in general. I will always have a special place in my heart for these cars. Heres to the 2gn community.
2005 Silver Subaru Legacy 2.5GT Turbo -Daily
1990 White SR powered 240sx - My sliding slut.
I miss my neon at times. She treated me well and taught me a lot about cars in general. I will always have a special place in my heart for these cars. Heres to the 2gn community.
-
LionheartedSXT
- 2GN Member
- Posts: 905
- Joined: Fri Jun 06, 2008 12:34 pm
- Location: Orlando, FL
Fuzzyneon wrote:how do you think sohc came along the one cam wonNutmeg wrote:I didn't know cams dueled.
You two are ridiculous-Chad
- Feedback
- Project LogMoxHair wrote:pay no attention to the man behind the curtain. Its all smoke and mirrors.
- Feedback
-
occasional demons
- Junior Admin
- Posts: 20064
- Joined: Thu May 03, 2007 12:14 pm
- Location: Ashland Ohio
Psh, as long as squealing pigs don't come into the conversation, it's all good.
OOPS! 
Back on topic..... 
OOPS! Back on topic..... Bill
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap
Probably shouldn't listen to anything your penis says, that guy's a dick.
Too much time spent here is a sign of a bad case of Ownaneonvirus.Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap