acr srt4 rediator

This is the place to ask questions about your engine components like cams, valves, pistons… just anything that is generally "engine" specific. This also includes questions about exhaust systems such as exhaust manifolds, piping size, mufflers, ect...
Post Reply
nateneon
n00b
Posts: 22
Joined: Tue May 27, 2008 8:32 pm
Location: council bluffs

acr srt4 rediator

Post by nateneon » Sat Sep 27, 2008 9:24 pm

will a radiator from an srt4 swap into a 2002 acr? i was looking at some on ebay, koyo brand to be exact but they were made for an srt4 and didnt know if i could just buy it for my neon acr????thanx!

User avatar
thttxboy
2GN Member
Posts: 979
Joined: Mon Jan 28, 2008 9:27 pm
Location: No. VA

Post by thttxboy » Sat Sep 27, 2008 9:46 pm

yes all 2gns have the same mounting brackets so its a direct fit.

racer12306
Junior Admin
Posts: 16015
Joined: Sun Oct 24, 2004 8:53 pm
Location: Baltimore, MD
Contact:

Post by racer12306 » Sat Sep 27, 2008 10:03 pm

are the outlets at the correct place?
-Frank
Member of Spork Racing
Forum issues: racer12306@2gn.org
Forum Behavior
Support your favorite forum, DONATE!

User avatar
thttxboy
2GN Member
Posts: 979
Joined: Mon Jan 28, 2008 9:27 pm
Location: No. VA

Post by thttxboy » Sat Sep 27, 2008 11:34 pm

Yes I just looked it up and if u order a radiator from KOYO it says Neon/SRT-4 so since the mortor is the same on all 2gns except the srt it should fit the 2002 motors. and people have swapped the srt radiators into basic neons. but only manual trans u have to buy a seperate oil cooler from them for the automatics. Heres an ebay linkhttp://cgi.ebay.com/ebaymotors/KOYO-ALUMINUM-RACING-RADIATOR-DODGE-NEON-SRT-4-01-02-04_W0QQcmdZViewItemQQ_trkparmsZ72Q3a1205Q7c39Q3a1Q7c66Q3a2Q7c65Q3a12Q7c240Q3a1318QQ_trksidZp3286Q2ec0Q2em14QQhashZitem170266280811QQitemZ170266280811

User avatar
Nutmeg
2GN Member
Posts: 1524
Joined: Wed May 16, 2007 7:14 pm
Location: Washington

Post by Nutmeg » Sun Sep 28, 2008 2:01 am

Why would you want to? The SRT has two fans, the Neon one. It may throw the computer off.
Image

OB
Former Moderator
Posts: 9686
Joined: Tue Nov 15, 2005 9:38 pm
Location: Bay Area, CA

Post by OB » Sun Sep 28, 2008 2:15 am

^That can easily be fixed with a manual fan switch for the second fan. What's a little wiring.

Other than the fans, I was under the impression that they were the same internally. If so, no reason to swap for the SRT one. Anyone know more about this?
-Derek

|Donate to 2gn|Feedback || OB's | GozziFab | All Business |


Wenuden
2GN Member
Posts: 2554
Joined: Fri Apr 06, 2007 11:53 pm
Location: Alexandria, Va

Post by Wenuden » Sun Sep 28, 2008 6:01 am

My srt core was thicher than my sxt core. Otherthan that, no difference. There may be 1 extra "row" of tubes, but with the plastic end caps there was no way for me to be sure.
Image

occasional demons
Junior Admin
Posts: 20067
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Sun Sep 28, 2008 11:52 am

There is a post somewhre here either in the project logs or swap section that shows the difference. It is signifigant, but unless you are putting down serious hp, the stock one will work fine. If the PCM was wired it may run the low speed fan. This was a CEL code I had when my Neon was wrecked. Short or open in low speed fan relay circuit. That only applies to SRT-4 as far as Neons(?) Mine is an '01 SE. So the programming is in there, just a matter of being able to utilize it. But IIRC the single fan will mount to the SRT radiator, may take some minor fabbing. One fan weighs less than two.
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

Post Reply

Return to “Engine”