HID bulb (((NOW))) in my halo Projectors !!

warriorr · Post by **warriorr** » Mon Oct 06, 2008 1:08 pm

Tryed last night to add on my HID H1 6000k. I both the halo projector & the bulb is to long for the projector !!

What are my options ?
Can I change only the bulb ? Or will have to buy the complet kit again ? How many H1 bulbs is there !?
Need assistance A.S.A.P !!!

Fuzzyneon · Post by **Fuzzyneon** » Mon Oct 06, 2008 3:07 pm

No you need to take a drill and mod the whole in the projector youll see a little like metal edge in there you need to drill out a little to fit the hole. just had to do the same thing to get mine to fit.

Will the HID's fit into the projectors?
It depends on where you buy yours from. Some people have had no problems. I was actually scraping the sides of the insert when I tried to put my HID bulbs in, so I took a 3/8 drill bit to open them up a bit, and it works great, they are completely snug and and fit fine.

warriorr · Post by **warriorr** » Mon Oct 06, 2008 5:21 pm

3/8 drill bit to open them up a bit !!! Yes I saw that Thks !! But the bulb is touching inside once I'm in 3/4 of the way

It's it possible that I got a typicale H1 bulb ?

Here's a pic. and tell me if this is right !!

It's 1 inch 3/4 long ! Is that what you have ?

Here's the kit !!

Anyway hope you could help me on this one !!

Fuzzyneon · Post by **Fuzzyneon** » Mon Oct 06, 2008 6:27 pm

warriorr wrote:3/8 drill bit to open them up a bit !!! Yes I saw that Thks !! But the bulb is touching inside once I'm in 3/4 of the way

It's it possible that I got a typicale H1 bulb ?

Here's a pic. and tell me if this is right !!

It's 1 inch 3/4 long ! Is that what you have ?

Here's the kit !!

Anyway hope you could help me on this one !!

pics dont work but mine fit about half to 3/4 in and stopped it i drilled and it fit snug in there!

warriorr · Post by **warriorr** » Mon Oct 06, 2008 8:17 pm

Do you have a bulb that long that's my next question ?
If so I'm not that crazy after all !!

Still looking here & there for info !

stang892k5 · Post by **stang892k5** » Mon Oct 06, 2008 8:22 pm

i just purchased the projector lights from modern and the hid kit that i own is a xetronic kit. they sell a bulb that is specifically for that problem its call the (H1p) bulb, the "p" meaning "projector" bulb . im not sure if it will work for your hid kit but you should look into it [url]www.xtralights.com

warriorr · Post by **warriorr** » Mon Oct 06, 2008 8:52 pm

Thks !! But they are not in there I've check for H1p bulbs & the web and no results so far. Will keep looking !!

Fuzzyneon · Post by **Fuzzyneon** » Mon Oct 06, 2008 9:22 pm

never measured mine but i know there a little longer then the stock ones in the projectors they look about the same size a drill and 5 minutes and they will go right in!

ZeroChad · Post by **ZeroChad** » Mon Oct 06, 2008 10:16 pm

Double check that the base or the shaft of the bulb is not contacting around the hole. *thats what she said* Those projectors should have more than 2in depth to them. Just watch out for the shavings when you're drilling. I did my upside down and still managed to get some shavings in the headlight housing.

warriorr · Post by **warriorr** » Tue Oct 07, 2008 9:59 am

OK will look at it closely to see if it's the bulb or me !!! I have tryed it 3,4 times & could not belive it !!!:omgshocked:

If you know any one that did this with the projectors let me know !!
BTW it as to be the 03 and up for the projectors cause I don't know if it is the same projectors.
I saw & compare the HID bulb with the stock H1 and there is not much of a difference.........

kornholio788 · Post by **kornholio788** » Tue Oct 07, 2008 10:10 am

Are you sure your bulb is touching the projector? I doubt it. I am pretty sure mine were that long too. BUT I did see something here.

See the two little tabs on the base by the bulbs? I had to trim those off. Mine were just plastic so I very carefully took a very sharp razor and took them off. I also had to shave down the bulb hole a little to get the HID to fit. Just took a file and held the headlight upside down so no file shavings fell in the projector. Then it fit nice and snug. I would look into that.

Caraudioholic24 · Post by **Caraudioholic24** » Tue Oct 07, 2008 12:25 pm

I didnt have to drill at all. I cut the plastic nubs on the hid bulb and the metal on the bulb will slide right into the gap in the projector. I wish I took pics but will have some over the winter since Im going to buy a new set.

warriorr · Post by **warriorr** » Tue Oct 07, 2008 12:54 pm

Thks for the input will keep you guy's posted.
Will try to make them fit some how !!

orangeblast05 · Post by **orangeblast05** » Tue Oct 07, 2008 1:33 pm

i didnt have any problems installing mine..

warriorr · Post by **warriorr** » Tue Oct 07, 2008 8:23 pm

I would like to say thks to Fuzzyneon, ZeroChad, kornholio788, Caraudioholic24 for the big support that I have received.
I was in pieces wen I first tryed it and did not work.
Now I'm just glad it working.....

I know you can't see much but it's pretty bright .

Big THKS !!! Guy's I don't no what would I do without you !!!!

kornholio788 · Post by **kornholio788** » Tue Oct 07, 2008 10:03 pm

warriorr wrote: Big THKS !!! Guy's I don't no what would I do without you !!!!

Masturbate alone?

ZeroChad · Post by **ZeroChad** » Tue Oct 07, 2008 10:49 pm

Nice! Glad you got em working.

Just a heads up, if you make the opening that the wires go through in that big rubber seal larger, that smaller rubber grommet can be used as a seal, letting less water in.

Fuzzyneon · Post by **Fuzzyneon** » Wed Oct 08, 2008 10:54 am

Very nice always glad to help

And korn its always better to bring a friend lol

kornholio788 · Post by **kornholio788** » Wed Oct 08, 2008 11:28 am

Fuzzyneon wrote:Very nice always glad to help

And korn its always better to bring a friend lol

Circle jerks?

Fuzzyneon · Post by **Fuzzyneon** » Wed Oct 08, 2008 8:37 pm

kornholio788 wrote:
Fuzzyneon wrote:Very nice always glad to help

And korn its always better to bring a friend lol
Circle jerks?

you're sterile from the mountain dew overage ! Lol

2GN.ORG

HID bulb (((NOW))) in my halo Projectors !!

HID bulb (((NOW))) in my halo Projectors !!

metal edge !!!

Re: metal edge !!!