A/C Heat controls not working

Questions about AMPs, headunits, speakers, subs, security systems, ect... Anything to do with audio or security, those questions all go here.
Post Reply
User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

A/C Heat controls not working

Post by sullivan » Thu Oct 23, 2008 12:11 pm

ok today my heat stopped working, and ac is also not working. there is power going to the controls, but no air blowing.... where is the blower motor fuses located?

User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

Post by sullivan » Thu Oct 23, 2008 12:33 pm

the blower motor fuse in the car is fine...

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Thu Oct 23, 2008 12:47 pm

If it is just a case of the fan not blowing, check for current to the motor. If it's getting power but not blowing, the motor is bad. If power is going to the blower resistor but not to the motor, the resistor is bad.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

Post by sullivan » Thu Oct 23, 2008 2:28 pm

hmm thanks man... where exactly is the motor located?

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Thu Oct 23, 2008 2:33 pm

Under the dash on the passenger side in the HVAC box.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

Post by sullivan » Thu Oct 23, 2008 2:41 pm

thanks man ill be pulling it apart tommrow...
Image
My AIM Username is sullivan_is_back@hotmail.com (yes @hotmail.com)

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Thu Oct 23, 2008 2:53 pm

Good deal. You can get to the motor without removing anything. IIRC, it hangs straight down from the box. It should have two good sized wires going to it.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

Post by sullivan » Fri Oct 24, 2008 12:21 am

so i dont have to remove any dash parts?
Image
My AIM Username is sullivan_is_back@hotmail.com (yes @hotmail.com)

slow2.0ts13
2GN Member
Posts: 165
Joined: Mon Sep 29, 2008 3:17 pm

Post by slow2.0ts13 » Fri Oct 24, 2008 8:39 am

Didnt you just have an issue with your deck fuse? check your fuse.
Image

occasional demons
Junior Admin
Posts: 20064
Joined: Thu May 03, 2007 12:14 pm
Location: Ashland Ohio

Post by occasional demons » Fri Oct 24, 2008 9:34 am

sullivan wrote:the blower motor fuse in the car is fine...
Bill
Probably shouldn't listen to anything your penis says, that guy's a dick.
Patience, of course, is a very powerful weapon, but sometimes I start to regret that it is not a firearm.
Too much time spent here is a sign of a bad case of Ownaneonvirus.

2000 Neon MTX swap with '02 R/T PCM
1999 neon coupe 2.4 swap

User avatar
Danteneon
Former Moderator
Posts: 9591
Joined: Thu Dec 20, 2007 5:13 pm
Location: Manassas, VA

Post by Danteneon » Fri Oct 24, 2008 9:51 am

sullivan wrote:so i dont have to remove any dash parts?
Not to get to the blower motor.
If I could just figure out how to meld the Outback and the Neon into one car...

Image

slow2.0ts13
2GN Member
Posts: 165
Joined: Mon Sep 29, 2008 3:17 pm

Post by slow2.0ts13 » Fri Oct 24, 2008 12:34 pm

occasional demons wrote:
sullivan wrote:the blower motor fuse in the car is fine...
he said the same thing about his radio fuse, and after 2 days of posting he figured out is was blown...
Image

User avatar
sullivan
2GN Member
Posts: 1103
Joined: Tue Oct 14, 2008 8:41 pm
Location: Sarnia,Ontario. Canada

Post by sullivan » Sat Oct 25, 2008 2:42 pm

hahaha no i didnt..... my deck what? lol

i think your confusing me with someone else.....

Post Reply

Return to “Audio / Security / Electrical”