I got Slammed B-othc and FML

v95 · Post by **v95** » Fri Apr 17, 2009 9:31 am

For all those people who told me to get slammed, This One For You

8:30am

now time to begin undoing the bolts holding the struts up.

cant fully break it lets get a hammer. lol to help.

the third hammer finally does the trick then Fuzzy Show up with the jesus bar an 80FtLbs torque wrench and helps break the rest of the bolts off

Now further reading requires a special tool and a vice

Stairs work just as well.
after taking all four struts off and between two jacks a block of wood and cinder blocks, were making progress.

Time to try and get these screws off the top and low and behold the require a special tool to take off these nuts. one to turn and the other part of the wrench to hold the one bolt down. call teamlivid for advice and lean of ghetto way of breaking the bolts. Does not work. people were giving us strange look as we where pounding the crap out of them to break them.
It the bolt right in the center that lock the springs down.

After about an hour and a half of us jumping on this thing it would not budge. so lets take it to a shop. After we get there only pay 100 to swap springs and then go home and have pizza bites.

Yeah pizza bite. after that go back to the garage to get struts with megan lowering springs. takes about thirty minutes to put both front springs on and then we get to the back
back one we can't get to line up now. fuzzy all of a sudden after fifteen minutes of fighting realizes that he used a jack to make everything fit. so we get the hand cranker and the impact drill and go to town and in about another thirty minutes this was the results.

LilSparkPlug · Post by **LilSparkPlug** » Fri Apr 17, 2009 10:15 am

Wow your car has lots of colors going on lol. What color will it be when you're done? The stock color? And there are easier ways to get the shock nut off without power tools, but they suck more than paying a shop to do it that has the right tools lol.

Drop looks good though

lilnicko11 · Post by **lilnicko11** » Fri Apr 17, 2009 10:40 am

drop looks good

Mopar00Neon · Post by **Mopar00Neon** » Fri Apr 17, 2009 11:52 am

Blocks, stock jack, and floor jack? Time for a set of jackstands maybe?

supermike · Post by **supermike** » Fri Apr 17, 2009 12:34 pm

Mmmm... that looks good. Different colored bumpers FTW. It's so much easier to find my car in parking lots!

ZeroChad · Post by **ZeroChad** » Fri Apr 17, 2009 1:19 pm

Those megan springs give a pretty even drop; I like it!

Fuzzyneon · Post by **Fuzzyneon** » Fri Apr 17, 2009 1:28 pm

he is on 15's im on 16's he is lower then me in the front barley but a hair it gives a very even drop <3

LSP yeah we evened up talking to jerry and joe (thanks for the help guys we just sucked to bad to figure it out) figured out how to do it but didnt have a ratchet big enough to get leverage

Tam · Post by **Tam** » Fri Apr 17, 2009 1:41 pm

Wow, I didn't know people found it this hard to lower a car.

Fuzzyneon · Post by **Fuzzyneon** » Fri Apr 17, 2009 1:44 pm

Mat666 wrote:Wow, I didn't know people found it this hard to lower a car.

it wasn't hard it was more lack of a few tools we couldn't find to rent or buy that would of made this easy

MyNeonSaysHi · Post by **MyNeonSaysHi** » Fri Apr 17, 2009 2:11 pm

To get that center bolt off you need a very long pair of giant vice grips and an impact gun. Hold the rod still with vicegrips and pound at it with the gun. But of course you didn't have access to those tools. Tahts good you had a shop do it and save the headache. $100 seems a little overpriced but its all good.

Car looks great lowered.

LilSparkPlug · Post by **LilSparkPlug** » Fri Apr 17, 2009 2:41 pm

No need for big rachets....I have a piece of pipe here that I use as leverage when I can't loosen a bolt with a hand tool. It's friggin amazing. Pipes FTW

You should NEVER put vice grips on a rod of a strut, any imperfection in the surface can cause it to blow.

theTeejmiester · Post by **theTeejmiester** » Fri Apr 17, 2009 2:53 pm

not sure if you tried it but this is a hell of a tool combo to break the top nuts on the struts,mine were on pretty damn tight and it worked fine,

again i dont know if that helps or if you already saw it

PS drop looks good but you are not slammed

Fuzzyneon · Post by **Fuzzyneon** » Fri Apr 17, 2009 6:54 pm

theTeejmiester wrote:not sure if you tried it but this is a hell of a tool combo to break the top nuts on the struts,mine were on pretty damn tight and it worked fine,

again i dont know if that helps or if you already saw it

PS drop looks good but you are not slammed

and i wish i had youre info to call you lol we where doing it so wrong

Sykora · Post by **Sykora** » Fri Apr 17, 2009 9:02 pm

what does "slammed mean?"

FAC3L3SS · Post by **FAC3L3SS** » Fri Apr 17, 2009 9:09 pm

what does b-othc mean...and what does FML have to do with any of it?

Fuzzyneon · Post by **Fuzzyneon** » Fri Apr 17, 2009 9:40 pm

FAC3L3SS wrote:what does b-othc mean...and what does FML have to do with any of it?

fml was the headache it cause us to do it not having proper tools ect

v95 · Post by **v95** » Sat Apr 18, 2009 12:28 am

Fuzzyneon wrote:
FAC3L3SS wrote:what does b-othc mean...and what does FML have to do with any of it?
fml was the headache it cause us to do it not having proper tools ect

and B-otch just seemed to be something interesting to bring back from the grave that my brother buried it in from over use. and plus we got to have some gangsta word cause this was a mad ghetto job. lol

MyNeonSaysHi · Post by **MyNeonSaysHi** » Sat Apr 18, 2009 12:40 am

LilSparkPlug wrote:No need for big rachets....I have a piece of pipe here that I use as leverage when I can't loosen a bolt with a hand tool. It's friggin amazing. Pipes FTW

You should NEVER put vice grips on a rod of a strut, any imperfection in the surface can cause it to blow.

It was on my stock strut. Stock struts were worthless. I was going with Tokico HP blues at the time on my 01 Neon.

blueneo03 · Post by **blueneo03** » Sat Apr 18, 2009 12:55 am

when i was takin my struts off i just used an impact wrench.. like socket on top pressed the trigger and it came off fine... lol no vice grips or anything... worked well..on and off. if you are gonna work on suspension i would recommend an impact wrench... well worth it.. imo

contagious18 · Post by **contagious18** » Sat Apr 18, 2009 12:48 pm

drop looks good