woohoo it came today

onewickedkid05 · Post by **onewickedkid05** » Wed Jun 17, 2009 4:57 pm

So this came in the mail today Now all i need are the belts and the puller i believe and i can install

v95 · Post by **v95** » Wed Jun 17, 2009 5:00 pm

so its still got power steering and ac or you deleting both or just ac

onewickedkid05 · Post by **onewickedkid05** » Wed Jun 17, 2009 5:13 pm

it still has both and i plan on having both

mr_mopar_neon · Post by **mr_mopar_neon** » Wed Jun 17, 2009 5:39 pm

little tip for pulling the old one of use a longs bolt but drill a small hole in the top of the bolt for the pully to sit into works great stops it from walking of the top.

as for the pully great bit of kit well worth putting on

onewickedkid05 · Post by **onewickedkid05** » Wed Jun 17, 2009 6:02 pm

What?

What exactly does the puller do does it remove the pulley all the way or is there something else i have to remove to get the pulley off (beside the belts)

And when i put it on how do i make sure its fully seated.....i dont want to get stuck halfway because im not prepared

alsey_seven · Post by **alsey_seven** » Wed Jun 17, 2009 6:31 pm

onewickedkid05 wrote:What?

What exactly does the puller do does it remove the pulley all the way or is there something else i have to remove to get the pulley off (beside the belts)

And when i put it on how do i make sure its fully seated.....i dont want to get stuck halfway because im not prepared

Here U go all the info you need

onewickedkid05 · Post by **onewickedkid05** » Wed Jun 17, 2009 6:54 pm

where do uy get that tool at

alsey_seven · Post by **alsey_seven** » Wed Jun 17, 2009 6:57 pm

he 3jaw puller? at sears autozone i got mine from harbor frieght 15.99 worked great didn't break strong like a rock

onewickedkid05 · Post by **onewickedkid05** » Wed Jun 17, 2009 9:53 pm

no the one to put it back on lol

onewickedkid05 · Post by **onewickedkid05** » Thu Jun 18, 2009 3:21 pm

whats that tool they are using to put the pulley back on? and whats the parts number of the pulley at autozone does anyone know i only see the one for napa

alsey_seven · Post by **alsey_seven** » Thu Jun 18, 2009 3:25 pm

well i used this methode of installing the pully it worked great for me.

http://chronoscender.freeservers.com/ne ... gbelt.html

right now i'm building a bolt installer at work using heavduty metal to make the tool u see above will have pics soon

onewickedkid05 · Post by **onewickedkid05** » Thu Jun 18, 2009 5:31 pm

so what to get the pulley on all the way heat it up slide it as far as it will go and just put the bolt on and torque it with a wrench causing the pulley to get pushed back?? or what

mr_mopar_neon · Post by **mr_mopar_neon** » Thu Jun 18, 2009 5:46 pm

thats all i did but dint heat it up. just a little of copper slip

INVUJerry · Post by **INVUJerry** » Thu Jun 18, 2009 5:48 pm

I put a little motor oil on the crank snout and banged it on with an impact gun.

onewickedkid05 · Post by **onewickedkid05** » Fri Jun 19, 2009 12:56 am

lol well no IMPAct THIS KIT I GOT HAs like 33 pieces im assuming i dont need all 33 lol

this is the kit

and im assuming this is all i need to install not including my ratchet to take it off and just SLide the new one on and if it doesnt go all the way put the screw in and force it that way?
To use it properly i need to put that black screw all the way threw then back it off, i keep seeing a wrench holding somehting in front of the ratchet what is that?

how do i stop the crank from turning when i remove the bolt?