rebuild ideas/help

mr_mopar_neon · Post by **mr_mopar_neon** » Wed Jul 15, 2009 5:11 pm

right guys and girls looking for a little advice after messing my engine up with to much nitrous and now it wont rev over 4000rpm with out banging and popping realy loud am going to rebuild it a lot stronger and faster.

just need to know whats good and whats bad

been looking at this rebuild kit
http://www.modernperformance.com/bottom ... -1607.html
is this any good thinkin of going the hole hog

and been looking at the zex street cam. is this any good for my r/t???
http://www.zex.com/Products/Valvetrain/ ... shafts.asp

i know this is not every think i need like vales and cam gears but just really looking for advice from ppl who have or have used these parts. any help would be great

excon · Post by **excon** » Wed Jul 15, 2009 7:16 pm

Since you're rebuilding it get forged internals. It will be much stronger. Now is the time to go turbo!

Haganracing · Post by **Haganracing** » Wed Jul 15, 2009 7:17 pm

Modern performance is full of wins

Adionik · Post by **Adionik** » Wed Jul 15, 2009 7:48 pm

Forged rods and pistons FTW

Get the 8.8.1 compression if you ever decide to turbo that bish

hybrid-Srt2001 · Post by **hybrid-Srt2001** » Wed Jul 15, 2009 8:16 pm

is the motor shot for sure? sounds like a map sensor problem

Post by **occasional demons** » Wed Jul 15, 2009 11:16 pm

hybrid-Srt2001 wrote:is the motor shot for sure? sounds like a map sensor problem

I would have to agree, (not actually hearing it run). If it seems fine below 4000 rpm, I wouldn't think it was a mechanical problem. If it back fired the IM at all, it may have messed up the MAP sensor.

DroopDaddy408 · Post by **DroopDaddy408** » Thu Jul 16, 2009 12:40 am

I been looking at this rebuild kit too, http://www.modernperformance.com/index.php
What does it actually do? Does it bring it up to factory specs or make it stronger?
Sorry, not trying to hijack. But it has to do with the ? that is asked...

mr_mopar_neon · Post by **mr_mopar_neon** » Thu Jul 16, 2009 3:33 pm

would you go one better on thne cam???
like a 400 but were do you get one from???

if using a 400 cam would there be any valve clearance issues when using 10.5:1 pistons????

neonslg09 · Post by **neonslg09** » Thu Jul 16, 2009 9:55 pm

mr_mopar_neon wrote: if using a 400 cam would there be any valve clearance issues when using 10.5:1 pistons????

i believe not. ZeroChad just did his rebuild and he has the 400 cam and 10.5:1 forged internals. check out his log for more info.

mr_mopar_neon · Post by **mr_mopar_neon** » Fri Jul 17, 2009 3:56 pm

thanks man

mr_mopar_neon · Post by **mr_mopar_neon** » Mon Jul 20, 2009 5:52 am

right after talking to ZeroChad i have just ordered the comp cam 400 and a Fidanza cam gear.

going to wait to open the mottor up before getting the rebuild kit want to way every thing up 1st.

thanks for every ones help any more help would be great

mr_mopar_neon · Post by **mr_mopar_neon** » Thu Jul 23, 2009 3:45 pm

right 1st part came to day some how it only took 3 days from the us

just waiting for the cam now.

what pcm would be best for my set up

nain things pistons, cam, head work, air intake st/st header and exhust????