Have some questions about how to achive better handling and stopping power using different springs, upgrading to coilovers, questions on swaybars, bushings, different rotors, pads, ect... Having any steering problems or questions about steering racks, tie rods, tie rod ends, ect... ask these questions here.
-
drftz31
- 2GN Member
- Posts: 73
- Joined: Fri Nov 16, 2007 1:47 pm
Post
by drftz31 » Thu Jul 23, 2009 7:44 pm
I just changed the brakes and rotor on the car and when the car is at 15mph plus. The car begains to shack..It sounds like the whole interior is shacking everything sounds like its going to fall out..when its not. I thought it was the motor mount but i changed it and still the same..i have no other clue and looking for help..thanks
-
neonslg09
- 2GN Veteran
- Posts: 5590
- Joined: Wed May 06, 2009 7:17 pm
- Location: Fredericksburg, Virginia
Post
by neonslg09 » Thu Jul 23, 2009 7:45 pm
are you wheels tight???
-
drftz31
- 2GN Member
- Posts: 73
- Joined: Fri Nov 16, 2007 1:47 pm
Post
by drftz31 » Thu Jul 23, 2009 7:51 pm
yup that was the first thing i thought but it wasnt that
-
neonslg09
- 2GN Veteran
- Posts: 5590
- Joined: Wed May 06, 2009 7:17 pm
- Location: Fredericksburg, Virginia
Post
by neonslg09 » Thu Jul 23, 2009 7:54 pm
i think you should check to make sure every bolt is tightened down. then make sure you installed everything in the correct orientation. other than that, i have no idea what is the issue.
-
drftz31
- 2GN Member
- Posts: 73
- Joined: Fri Nov 16, 2007 1:47 pm
Post
by drftz31 » Thu Jul 23, 2009 7:59 pm
yeah everything is tight and the way it should be.. i have no idea either..thats why im seeing if anyone has had this before
-
darthroush
- 2GN Member
- Posts: 1637
- Joined: Tue Jul 14, 2009 2:14 am
- Location: People's Republic of Kalifornia
Post
by darthroush » Thu Jul 23, 2009 8:07 pm
Sounds like warped rotors, but they are new?
-
drftz31
- 2GN Member
- Posts: 73
- Joined: Fri Nov 16, 2007 1:47 pm
Post
by drftz31 » Thu Jul 23, 2009 8:26 pm
yeah it a brand new one.. my friend told me that it could be the lower motor mount so i will screw with it when my daughter goes to sleep for the night.
-
Donkeypuncher
- 2GN Member
- Posts: 2183
- Joined: Wed Mar 12, 2008 6:14 am
- Location: Dallas, Tx
Post
by Donkeypuncher » Thu Jul 23, 2009 9:10 pm
Is the rotor seated all the way on the hub? Maybe some rust or debris is holding it slightly offset.
-
mattern248
- 2GN Member
- Posts: 514
- Joined: Tue Jun 24, 2008 7:43 pm
- Location: prescott valley, az
Post
by mattern248 » Thu Jul 23, 2009 11:55 pm
check you u joint or ball joint thing whatever it's called mines blown so it rattle more then two bees going at it. plus it should pull a little to one side then the other

93 talon tsi awd 430 awhp at 24 psi--sold
04 se to 2.0l srt daily whip
95 yzf 600 bored to a 750 weekend fun toy
97 camaro v6 supercharged teh wifeys
03 tiby---mommy mobile
-
Donkeypuncher
- 2GN Member
- Posts: 2183
- Joined: Wed Mar 12, 2008 6:14 am
- Location: Dallas, Tx
Post
by Donkeypuncher » Fri Jul 24, 2009 7:37 am
Nice english and proper grammar.
Since it started immediately after a brake job, I'm guessing it's something related to that.